IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This way, we should be in a slightly better situation if a container is
booted up with only a shell as PID 1. In that case
/run/systemd/container will not be populated, and a check for it hence
be ineffective.
Checking /proc/1/environ doesn't fully fix the problem though, as the
file is only accessible with privileges. This means if PID 1 is not
systemd, and if privileges have been dropped the container detection
will continue to fail.
The error was introduced in v215-343-g60731f32f1 'systemctl: do not
bother to mutate state on error', by causing strv_free to attempt to
free a static string. Simplify the whole thing by always keeping the
array in valid state.
loop_write() didn't follow the usual systemd rules and returned status
partially in errno and required extensive checks from callers. Some of
the callers dealt with this properly, but many did not, treating
partial writes as successful. Simplify things by conforming to usual rules.
Suppose that while iterating we have already looked into a journal file
and got a candidate for the next entry. And we are considering to look
into another journal file because it may contain an entry that is nearer
to the current location than the candidate.
We should skip the whole journal file if we can tell by looking at its
header that none of its entries can precede the candidate.
Before:
$ time ./journalctl --since=2014-06-01 --until=2014-07-01 > /dev/null
real 0m20.518s
user 0m19.989s
sys 0m0.328s
After:
$ time ./journalctl --since=2014-06-01 --until=2014-07-01 > /dev/null
real 0m9.445s
user 0m9.228s
sys 0m0.213s
Interleaving of entries from many journal files is expensive. But there
is room for optimization.
We can skip looking into journal files whose entries all lie before the
current iterating location. We can tell if that's the case from looking
at the journal file header. This saves a huge amount of work if one has
many of mostly not interleaved journal files.
On my workstation with 90 journal files in /var/log/journal/ID/
totalling 3.4 GB I get these results:
Before:
$ time ./journalctl --since=2014-06-01 --until=2014-07-01 > /dev/null
real 5m54.258s
user 2m4.263s
sys 3m48.965s
After:
$ time ./journalctl --since=2014-06-01 --until=2014-07-01 > /dev/null
real 0m20.518s
user 0m19.989s
sys 0m0.328s
The high "sys" time in the original was caused by putting more stress on
the mmap-cache than it could handle. With the patch the working set
now consists of fewer mmap windows and mmap-cache is not thrashing.
If a unit is set property by "systemctl set-property", a new dropin
file is generated. But the unit's dropin_paths and dropin_mtime are
not updated. So the unit is shown as need daemon reload.
Update unit dropin_paths and dropin_mtime also when dropin file is
written.
When dbus client connects to systemd-bus-proxyd through
Unix domain socket proxy takes client's smack label and sets for itself.
It is done before and independent of dropping privileges.
The reason of such soluton is fact that tests of access rights
performed by lsm may take place inside kernel, not only
in userspace of recipient of message.
The bus-proxyd needs CAP_MAC_ADMIN to manipulate its label.
In case of systemd running in system mode, CAP_MAC_ADMIN
should be added to CapabilityBoundingSet in service file of bus-proxyd.
In case of systemd running in user mode ('systemd --user')
it can be achieved by addition
Capabilities=cap_mac_admin=i and SecureBits=keep-caps
to user@.service file
and setting cap_mac_admin+ei on bus-proxyd binary.
Support timer options --on-active=, --on-boot=, --on-startup=,
--on-unit-active=, --on-unit-inactive=, --on-calendar=. Each options
corresponding with OnActiveSec=, OnBootSec=, OnStartupSec=,
OnUnitActiveSec=, OnUnitInactiveSec=, OnCalendar= of timer
respectively. And OnCalendar= and WakeSystem= supported by
--timer-property= option like --property= of systemd-run.
And if --unit= option and timer options are specified the command can
be omitted. In this case, systemd-run assumes the target service is
already loaded. And just try to generate transient timer unit only.
kdbus-git gained two new features:
* memfd offsets: This allows to specify a 'start' offset in kdbus_memfd
so you can send partial memfd hunks instead of always
the full memfd
* KDBUS_HELLO_UNPRIVILEGED: If passed during HELLO, the client will be
treated as unprivileged.
In the case where no entries have been added to the journal after the specified
cursor, set need_seek before the main loop to prevent display of the entry at
said cursor.
If a cgroup fails to be destroyed (most likely because there are still
processes running as part of a service after the main pid exits), don't
free and remove the cgroup unit from the manager. This fixes a
regression introduced by the cgroup rework in v205 where systemd would
forget about processes still running after the unit becomes inactive.
(This can happen when the main pid exits and KillMode=process or none).
There is no need to require mount.usrflags. The original implementation
assumed that a btrfs subvolume would always be needed but that is not
applicable to systems that do not use btrfs for /usr.
Similar to using rootflags= for the default of mount.usrflags=, append
the classic 'ro' and 'rw' flags to the mount options.
