IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This avoids having to distinguish between IPv4 and IPv6, allowing us
to keep their internal orderings. The consumers now has to turn the
strings into addresses.
networkd will expose both statically configured DNS servers and servers
receieved over DHCP in sd_network_get_dns(), so no need to keep
the distinction in resolved.
All routes added by networkd are currently set RTPROT_BOOT, which according
to the kernel means "Route installed during boot" (rtnetlink.h). But this
is not always the case as networkd changes routing after boot too. Since
the kernel gives more detailed protocols, use them.
With this patch, user-configured static routes now use RTPROT_STATIC (which
they are) and DHCP routes use RTPROT_DHCP. There is no define for IPv4LL
yet, so those are installed as RTPROT_STATIC (though perhaps RTPROT_RA is
better?).
[tomegun: fixup
src/network/networkd-link.c:972:33: error: too few arguments to function 'route_new_dynamic']
Also, fix fopen_temporary_label to set proper context. By chance,
all users so far used the same context, so the error didn't matter.
Also, check return value from label_init().
https://bugzilla.redhat.com/show_bug.cgi?id=1121806
Lennart said:
> We have these nice USEC_PER_MSEC-style macro definitions which make it a
> little bit clearer what we are converting here from what into
> what... please use that instead of writing "1000"...
>
> (we stole those from gstreamer btw)
The following bond options are supported by this patch.
MIIMonitorSec:
Specifies the frequency in milli-seconds that MII link
monitoring will occur.
UpDelaySec:
Specifies the delay time in milli-seconds to enable a link
after a link up status has been detected.
DownDelaySec:
Specifies the delay time in milli-seconds to disable a link
after a link failure has been detected.
changes:
1. Added gconf variables.
2. man page
conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
LacpduTransmitRate=fast
MIIMonitorSec=1s
UpDelaySec=2s
DownDelaySec=8s
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 1000
Up Delay (ms): 2000
Down Delay (ms): 8000
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: rephrased manpage, dropped bond_ prefix from variables]
LacpduTransmitRate
option specifies the rate in which link partner to transmit
LACPDU packets in 802.3ad mode. Possible values
slow : Request partner to transmit LACPDUs every 30 seconds
fast : Request partner to transmit LACPDUs every 1 second
The default is slow.
chages:
1. Added enum bond_lacp_rate_table
2. gperf LacpduTransmitRate
Test:
conf file:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
LacpduTransmitRate=fast
test:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: fast
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: renamed from LacpduTransmitRate to LACPTransmitRate, manpage fixes and
dropped bond_ prefix from variables]
This patch adds support the transmit hash policy to use
for slave selection in balance-xor, 802.3ad, and tlb modes
layer2, layer3+4, layer2+3, encap3+4, encap3+4
Added:
1. BondXmitHashPolicy
2. conf param TransmitHashPolicy
Test conf:
[NetDev]
Name=bond1
Kind=bond
[Bond]
Mode=802.3ad
TransmitHashPolicy=layer2+3
test output:
cat /proc/net/bonding/bond1
Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
Bonding Mode: IEEE 802.3ad Dynamic link aggregation
Transmit Hash Policy: layer2+3 (2)
MII Status: up
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
802.3ad info
LACP rate: slow
Min links: 0
Aggregator selection policy (ad_select): stable
bond bond1 has no active aggregator
[tomegun: dropped bond_ prefix from new Bond variable, drop repeated man-page section]
This tool will warn about misspelt directives, unknown sections, and
non-executable commands. It will also catch the common mistake of
using Accept=yes with a non-template unit and vice versa.
https://bugs.freedesktop.org/show_bug.cgi?id=56607
Commit 637f421e5c ("cgroups: always propagate controller membership
to siblings") changed the mask propagation logic, but the test wasn't
updated.
Move to normal tests from manual tests, it should not touch the system
anymore.
It seems that unit_get_siblings_mask returns the controllers
filtered by what is available, but get_members_mask and
get_cgroup_mask do not. This just fixes the test following the
symptoms.
Also add a bit of debugging output to help diagnose problems,
add missing units, and simplify cppflags.
Move test-engine to normal tests from manual tests, it should now
work without destroying the system.
If poll() returns, one of both revents must be set, thus "buf" is set by
either clause. This is non-obvious for code-checkers so add an "else
continue;" clause to suppress "uninitialized variable" warnings.
Our version has evolved independently of the original table
in systemd-config-keyboard, so it cannot be ever regenerated from
original upstream. Remove script to avoid confusion.
