IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The bitbbanging bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new driver API calls.
The SH Ethernet driver places wrappers around these functions. In
order to not break boards which might be using C45, add similar
wrappers for C45 operations.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that mdiobus_c45_addr() is only used within the MDIO code during
fallback, move the function next to its only users. This function
should not be used any more in drivers, the c45 helpers should be used
in its place, so hiding it away will prevent any new users from being
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a C22 operation, check that the bus driver actually
provides the methods, and return -EOPNOTSUPP if not. C45 only busses
do exist, and in future their C22 methods will be NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that C45 uses its own read/write methods, the validation performed
when a bus is registers needs updating. All combinations of C22 and
C45 are supported, but both read and write methods must be provided,
read only busses are not supported etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert the PCS-XPCS driver to make use of the C45 MDIO bus API for
modify_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently C22 and C45 transactions are mixed over a combined API calls
which make use of a special bit in the reg address to indicate if a
C45 transaction should be performed. This makes it impossible to know
if the bus driver actually supports C45. Additionally, many C22 only
drivers don't return -EOPNOTSUPP when asked to perform a C45
transaction, they mistaking perform a C22 transaction.
This is the first step to cleanly separate C22 from C45. To maintain
backwards compatibility until all drivers which are capable of
performing C45 are converted to this new API, the helper functions
will fall back to the older API if the new API is not
supported. Eventually this fallback will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Michael Walle says:
====================
net: phy: mxl-gpy: broken interrupt fixes
The GPY215 has a broken interrupt pin. This patch series tries to
workaround that and because in general that is not possible, disables the
interrupts by default and falls back to polling mode. There is an opt-in
via the devicetree.
====================
Link: https://lore.kernel.org/r/20230109123013.3094144-1-michael@walle.cc
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The interrupts on the GPY215B and GPY215C are broken and the only viable
fix is to disable them altogether. There is still the possibilty to
opt-in via the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Until now, it is not possible for a PHY driver to disable interrupts
during runtime. If a driver offers the .config_intr() as well as the
.handle_interrupt() ops, it is eligible for interrupt handling.
Introduce a new flag for the dev_flags property of struct phy_device, which
can be set by PHY driver to skip interrupt setup and fall back to polling
mode.
At the moment, this is used for the MaxLinear PHY which has broken
interrupt handling and there is a need to disable interrupts in some
cases.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the device tree bindings for the MaxLinear GPY2xx PHYs, which
essentially adds just one flag: maxlinear,use-broken-interrupts.
One might argue, that if interrupts are broken, just don't use
the interrupt property in the first place. But it needs to be more
nuanced. First, this interrupt line is also used to wake up systems by
WoL, which has nothing to do with the (broken) PHY interrupt handling.
Second and more importantly, there are devicetrees which have this
property set. Thus, within the driver we have to switch off interrupt
handling by default as a workaround. But OTOH, a systems designer who
knows the hardware and knows there are no shared interrupts for example,
can use this new property as a hint to the driver that it can enable the
interrupt nonetheless.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
MaxLinear is a manufacturer of integrated circuits.
https://www.maxlinear.com
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This implementation for the Marvell mv88e6xxx chip series is based on
handling ATU miss violations occurring when packets ingress on a port
that is locked with learning on. This will trigger a
SWITCHDEV_FDB_ADD_TO_BRIDGE event, which will result in the bridge module
adding a locked FDB entry. This bridge FDB entry will not age out as
it has the extern_learn flag set.
Userspace daemons can listen to these events and either accept or deny
access for the host, by either replacing the locked FDB entry with a
simple entry or leave the locked entry.
If the host MAC address is already present on another port, a ATU
member violation will occur, but to no real effect, and the packet will
be dropped in hardware. Statistics on these violations can be shown with
the command and example output of interest:
ethtool -S ethX
NIC statistics:
...
atu_member_violation: 5
atu_miss_violation: 23
...
Where ethX is the interface of the MAB enabled port.
Furthermore, as added vlan interfaces where the vid is not added to the
VTU will cause ATU miss violations reporting the FID as
MV88E6XXX_FID_STANDALONE, we need to check and skip the miss violations
handling in this case.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As only the hardware access functions up til and including
mv88e6xxx_g1_atu_mac_read() called under the interrupt handler
need to take the chip lock, we release the chip lock after this call.
The follow up code that handles the violations can run without the
chip lock held.
In further patches, the violation handler function will even be
incompatible with having the chip lock held. This due to an AB/BA
ordering inversion with rtnl_lock().
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f0063 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff75 ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the necessary changes to support 10 Mbps speed for BaseT and SFP
port modes. This is supported in MAC ver >= 30H.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://lore.kernel.org/r/20230109101819.747572-1-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This enables link partner advertised support to show link modes and
pause frame use.
Signed-off-by: Jamie Gloudon <jamie.gloudon@gmx.fr>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230103230653.1102544-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit ce098da1497c ("skbuff: Introduce slab_build_skb()")
drivers trying to build skb around slab-backed buffers should
go via slab_build_skb() rather than passing frag_size = 0 to
the main build_skb().
Remove the copy'n'pasted comments about 0 meaning slab.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork says:
====================
r8152: allow firmwares with NCM support
Some device and firmware combinations with NCM support will
end up using the cdc_ncm driver by default. This is sub-
optimal for the same reasons we've previously accepted the
blacklist hack in cdc_ether.
The recent support for subclassing the generic USB device
driver allows us to create a very slim driver with the same
functionality. This patch set uses that to implement a
device specific configuration default which is independent
of any USB interface drivers. This means that it works
equally whether the device initially ends up in NCM or ECM
mode, without depending on any code in the respective class
drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 driver does not need this anymore.
Dropping blacklist entries adds optional support for these
devices in ECM mode.
The 8153 devices are handled by the r8153_ecm driver when
in ECM mode, and must still be blacklisted here.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subclassing the generic USB device driver to override the
default configuration selection regardless of matching interface
drivers.
The r815x family devices expose a vendor specific function which
the r8152 interface driver wants to handle. This is the preferred
device mode. Additionally one or more USB class functions are
usually supported for hosts lacking a vendor specific driver. The
choice is USB configuration based, with one alternate function per
configuration.
Example device with both NCM and ECM alternate cfgs:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 3
P: Vendor=0bda ProdID=8156 Rev=31.00
S: Manufacturer=Realtek
S: Product=USB 10/100/1G/2.5G LAN
S: SerialNumber=001000001
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=256mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=128ms
C: #Ifs= 2 Cfg#= 2 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
C: #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
A problem with this is that Linux will prefer class functions over
vendor specific functions. Using the above example, Linux defaults
to cfg #2, running the device in a sub-optimal NCM mode.
Previously we've attempted to work around the problem by
blacklisting the devices in the ECM class driver "cdc_ether", and
matching on the ECM class function in the vendor specific interface
driver. The latter has been used to switch back to the vendor
specific configuration when the driver is probed for a class
function.
This workaround has several issues;
- class driver blacklists is additional maintanence cruft in an
unrelated driver
- class driver blacklists prevents users from optionally running
the devices in class mode
- each device needs double match entries in the vendor driver
- the initial probing as a class function slows down device
discovery
Now these issues have become even worse with the introduction of
firmware supporting both NCM and ECM, where NCM ends up as the
default mode in Linux. To use the same workaround, we now have
to blacklist the devices in to two different class drivers and
add yet another match entry to the vendor specific driver.
This patch implements an alternative workaround strategy -
independent of the interface drivers. It avoids adding a
blacklist to the cdc_ncm driver and will let us remove the
existing blacklist from the cdc_ether driver.
As an additional bonus, removing the blacklists allow users to
select one of the other device modes if wanted.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
mptcp: Protocol in-use tracking and code cleanup
Here's a collection of commits from the MPTCP tree:
Patches 1-4 and 6 contain miscellaneous code cleanup for more consistent
use of helper functions, existing local variables, and better naming.
Patches 5, 7, and 9 add sock_prot_inuse tracking for MPTCP and an
associated self test.
Patch 8 modifies the mptcp_connect self test tool to exit on SIGUSR1
when in "slow mode".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the function chk_msk_inuse() to diag.sh, which is used to check the
statistics of mptcp socket in use. As mptcp socket in listen state will
be closed randomly after 'accept', we need to get the count of listening
mptcp socket through 'ss' command.
All tests pass.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For now, mptcp_connect won't exit after receiving the 'SIGUSR1' signal
if '-r' is set. Fix this by skipping poll and sleep in copyfd_io_poll()
if 'quit' is set.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the statistics of mptcp socket in use with sock_prot_inuse_add().
Therefore, we can get the count of used mptcp socket from
/proc/net/protocols:
& cat /proc/net/protocols
protocol size sockets memory press maxhdr slab module cl co di ac io in de sh ss gs se re sp bi br ha uh gp em
MPTCPv6 2048 0 0 no 0 yes kernel y n y y y y y y y y y y n n n y y y n
MPTCP 1896 1 0 no 0 yes kernel y n y y y y y y y y y y n n n y y y n
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ssk' should be more appropriate to be the name of the first argument
in mptcp_token_new_connect().
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'sk_prot' field in token KUNIT self-tests will be dereferenced in
mptcp_token_new_connect(). Therefore, init it with tcp_prot.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'sock->sk' is used frequently in mptcp_listen(). Therefore, we can
introduce the 'sk' and replace 'sock->sk' with it.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The local variable 'ssk' has been defined at the beginning of the function
mptcp_write_options(), use it instead of getting 'ssk' again.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the local variable 'net' instead of sock_net() in the functions where
the variable 'struct net *net' has been defined.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper msk_owned_by_me() is defined in protocol.h, so use it instead
of sock_owned_by_me().
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current source pushes skb into dev-done queue by calling
skb_dequeue_tail() and then pop it by skb_dequeue() to branch to
rx_cleanup state for freeing urb/skb in usbnet_bh(). It takes extra CPU
load, 2.21% (skb_queue_tail) as follows,
- 11.58% 0.26% swapper [k] usbnet_bh
- 11.32% usbnet_bh
- 6.43% skb_dequeue
6.34% _raw_spin_unlock_irqrestore
- 2.21% skb_queue_tail
2.19% _raw_spin_unlock_irqrestore
- 1.68% consume_skb
- 0.97% kfree_skbmem
0.80% kmem_cache_free
0.53% skb_release_data
To reduce the extra CPU load use return values to call helper function
usb_free_skb() to free the resources instead of calling skb_queue_tail()
and skb_dequeue() for push and pop respectively.
- 7.87% 0.25% swapper [k] usbnet_bh
- 7.62% usbnet_bh
- 4.81% skb_dequeue
4.74% _raw_spin_unlock_irqrestore
- 1.75% consume_skb
- 0.98% kfree_skbmem
0.78% kmem_cache_free
0.58% skb_release_data
0.53% smsc95xx_rx_fixup
Signed-off-by: Leesoo Ahn <lsahn@ooseel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divya Koppera says:
====================
Fixed warnings
Fixed warnings related to PTR_ERR and initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the NULL pointer case
Fixes New smatch warnings:
drivers/net/phy/micrel.c:2613 lan8814_ptp_probe_once() warn: passing zero to 'PTR_ERR'
vim +/PTR_ERR +2613 drivers/net/phy/micrel.c
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialized return variable
Fixes Old smatch warnings:
drivers/net/phy/micrel.c:1750 ksz886x_cable_test_get_status() error:
uninitialized symbol 'ret'.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiawen Wu says:
====================
net: wangxun: Adjust code structure
Remove useless structs 'txgbe_hw' and 'ngbe_hw' make the codes clear.
And move the same codes which sets MAC address between txgbe and ngbe
to libwx. Further more, rename struct 'wx_hw' to 'wx' and move total
adapter members to wx.
====================
Link: https://lore.kernel.org/r/20230106033853.2806007-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to move the total members in struct adapter to struct wx_hw
to keep the code clean, it's a bad name of 'wx_hw' only for hardware.
Rename 'wx_hw' to 'wx', and rename the pointers at use.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For setting MAC address, both txgbe and ngbe drivers have the same handling
flow with different parameters. Move the same codes to libwx.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove useless structure ngbe_hw to make the codes clear.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove useless structure txgbe_hw to make the codes clear.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The lan8814 represents a package of 4 PHYs. All of them are sharing the
same interrupt line. So when a link was going down/up or a frame was
timestamped, then the interrupt handler of all the PHYs was called.
Which is all fine and expected but the problem is the way the handler
interrupt works.
Basically if one of the PHYs timestamp a frame, then all the other 3
PHYs were polling the status of the interrupt until that PHY actually
cleared the interrupt by reading the timestamp.
The reason of polling was in case another PHY was also timestamping a
frame at the same time, it could miss this interrupt. But this is not
the right approach, because it is the interrupt controller who needs to
call the interrupt handlers again if the interrupt line is still
active.
Therefore change this such when the interrupt handler is called check
only if the interrupt is for itself, otherwise just exit. In this way
save CPU usage.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20230104194218.3785229-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zero-length arrays are deprecated[1]. Replace struct ethtool_rxnfc's
"rule_locs" 0-length array with a flexible array. Detected with GCC 13,
using -fstrict-flex-arrays=3:
net/ethtool/common.c: In function 'ethtool_get_max_rxnfc_channel':
net/ethtool/common.c:558:55: warning: array subscript i is outside array bounds of '__u32[0]' {aka 'unsigned int[]'} [-Warray-bounds=]
558 | .fs.location = info->rule_locs[i],
| ~~~~~~~~~~~~~~~^~~
In file included from include/linux/ethtool.h:19,
from include/uapi/linux/ethtool_netlink.h:12,
from include/linux/ethtool_netlink.h:6,
from net/ethtool/common.c:3:
include/uapi/linux/ethtool.h:1186:41: note: while referencing
'rule_locs'
1186 | __u32 rule_locs[0];
| ^~~~~~~~~
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: kernel test robot <lkp@intel.com>
Cc: Oleksij Rempel <linux@rempel-privat.de>
Cc: Sean Anderson <sean.anderson@seco.com>
Cc: Alexandru Tachici <alexandru.tachici@analog.com>
Cc: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230106042844.give.885-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zero-length arrays are deprecated[1]. Replace struct ipv6_rpl_sr_hdr's
"segments" union of 0-length arrays with flexible arrays. Detected with
GCC 13, using -fstrict-flex-arrays=3:
In function 'rpl_validate_srh',
inlined from 'rpl_build_state' at ../net/ipv6/rpl_iptunnel.c:96:7:
../net/ipv6/rpl_iptunnel.c:60:28: warning: array subscript <unknown> is outside array bounds of 'struct in6_addr[0]' [-Warray-bounds=]
60 | if (ipv6_addr_type(&srh->rpl_segaddr[srh->segments_left - 1]) &
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from ../include/net/rpl.h:12,
from ../net/ipv6/rpl_iptunnel.c:13:
../include/uapi/linux/rpl.h: In function 'rpl_build_state':
../include/uapi/linux/rpl.h:40:33: note: while referencing 'addr'
40 | struct in6_addr addr[0];
| ^~~~
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230105221533.never.711-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
devlink: remove the wait-for-references on unregister
Move the registration and unregistration of the devlink instances
under their instance locks. Don't perform the netdev-style wait
for all references when unregistering the instance.
Instead the devlink instance refcount will only ensure that
the memory of the instance is not freed. All places which acquire
access to devlink instances via a reference must check that the
instance is still registered under the instance lock.
This fixes the problem of the netdev code accessing devlink
instances before they are registered.
RFC: https://lore.kernel.org/all/20221217011953.152487-1-kuba@kernel.org/
- rewrite the cover letter
- rewrite the commit message for patch 1
- un-export and rename devl_is_alive
- squash the netdevsim patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent races with netdev code accessing free devlink instances
move the registration under the devlink instance lock.
Core now waits for the instance to be registered before accessing it.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
