IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This commit adds a new platform-data boolean property that enables use
of a flash-based bad block table. This can also be enabled by setting
the 'nand-on-flash-bbt' devicetree property.
If the flash BBT is not enabled, the driver falls back to use OOB
bad block markers only, as before. If the flash BBT is enabled the
kernel will keep track of bad blocks using a BBT, in addition to
the OOB markers.
As explained by Brian Norris the reasons for using a BBT are:
""
The primary reason would be that NAND datasheets specify it these days.
A better argument is that nobody guarantees that you can write a
bad block marker to a worn out block; you may just get program failures.
This has been acknowledged by several developers over the last several
years.
Additionally, you get a boot-time performance improvement if you only
have to read a few pages, instead of a page or two from every block on
the flash.
""
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For NAND read & write wait pin monitoring must be kept disabled as the
wait pin is only used to indicate NAND device ready status and not to
extend each read/write cycle.
So don't print a warning if wait pin is specified while read/write
monitoring is not in the device tree.
Sanity check wait pin number irrespective if read/write monitoring is
set or not.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:
Add basic subarchitecture support for the DRA72x and DRA74x. These
are OMAP2+ derivative SoCs. This should be low-risk to existing OMAP
platforms.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/
* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending:
ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
Signed-off-by: Olof Johansson <olof@lixom.net>
To deal with IPs which are specific to dra74x and dra72x, maintain seperate
ocp interface lists, while keeping the common list for all common IPs.
Move USB OTG SS4 to dra74x only list since its unavailable in
dra72x and is giving an abort during boot. The dra72x only list
is empty for now and a placeholder for future hwmod additions which
are specific to dra72x.
Fixes: d904b38df0 ("ARM: DRA7: hwmod: Add SYSCONFIG for usb_otg_ss")
Reported-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
[paul@pwsan.com: fixed comment style to conform with CodingStyle]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Looks like MUSB cable removal can cause wake-up interrupts to
stop working for device tree based booting at least for UART3
even as nothing is dynamically remuxed. This can be fixed by
calling reconfigure_io_chain() for device tree based booting
in hwmod code. Note that we already do that for legacy booting
if the legacy mux is configured.
My guess is that this is related to UART3 and MUSB ULPI
hsusb0_data0 and hsusb0_data1 support for Carkit mode that
somehow affect the configured IO chain for UART3 and require
rearming the wake-up interrupts.
In general, for device tree based booting, pinctrl-single
calls the rearm hook that in turn calls reconfigure_io_chain
so calling reconfigure_io_chain should not be needed from the
hwmod code for other events.
So let's limit the hwmod rearming of iochain only to
HWMOD_FORCE_MSTANDBY where MUSB is currently the only user
of it. If we see other devices needing similar changes we can
add more checks for it.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: stable@vger.kernel.org # v3.16
Signed-off-by: Tony Lindgren <tony@atomide.com>
When an alias for a clock already exists the warning is printed. For
every module with a main_clk defined, a clk alias for fck is added.
There are some components that have the same main_clk defined, so this
is a really normal situation.
For example the am33xx edma device has 4 components using the same main
clock. So there are three warnings in the boot log for this already
existing clock alias:
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
platform 49000000.edma: alias fck already exists
As this is only interesting for developers, this patch changes the
message to a debug message.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.14 and prior, 1-bit Hamming code ECC via software was the
default choice for some boards e.g. 3430sdp.
Commit ac65caf514 in v3.15 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.14
and prior to be unusable in v3.15 and later. So don't mark "sw" scheme
as deperecated and support it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For v3.12 and prior, 1-bit Hamming code ECC via software was the
default choice. Commit c66d039197 in v3.13 changed the behaviour
to use 1-bit Hamming code via Hardware using a different ECC layout
i.e. (ROM code layout) than what is used by software ECC.
This ECC layout change causes NAND filesystems created in v3.12
and prior to be unusable in v3.13 and later. So revert back to
using software ECC by default if an ECC scheme is not explicitely
specified.
This defect can be observed on the following boards during legacy boot
-omap3beagle
-omap3touchbook
-overo
-am3517crane
-devkit8000
-ldp
-3430sdp
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "few omap fixes for v3.17 merge window" from Tony Lindgren:
Few fixes for the v3.17 merge window:
- Fix for DPLL rate rounding
- Fix for omap3 ES3.1.2 suspend
- Few coding style fixes
* tag 'omap-for-v3.17/soc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix coding style problems in arch/arm/mach-omap2/control.c
ARM: OMAP3: Fix choice of omap3_restore_es function in OMAP34XX rev3.1.2 case.
ARM: OMAP2+: clock: allow omap2_dpll_round_rate() to round to next-lowest rate
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Merging in the few fixes we had also received, no need to keep those in
a separate branch.
* next/fixes-non-critical:
drivers: CCI: Correct use of ! and &
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
Pull iommu updates from Joerg Roedel:
"This time with:
- support for the generic PCI device alias code in x86 IOMMU drivers
- a new sysfs interface for IOMMUs
- preparations for hotplug support in the Intel IOMMU driver
- change the AMD IOMMUv2 driver to not hold references to core data
structures like mm_struct or task_struct. Rely on mmu_notifers
instead.
- removal of the OMAP IOVMM interface, all users of it are converted
to DMA-API now
- make the struct iommu_ops const everywhere
- initial PCI support for the ARM SMMU driver
- there is now a generic device tree binding documented for ARM
IOMMUs
- various fixes and cleanups all over the place
Also included are some changes to the OMAP code, which are acked by
the maintainer"
* tag 'iommu-updates-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (67 commits)
devicetree: Add generic IOMMU device tree bindings
iommu/vt-d: Fix race setting IRQ CPU affinity while freeing IRQ
iommu/amd: Fix 2 typos in comments
iommu/amd: Fix device_state reference counting
iommu/amd: Remove change_pte mmu_notifier call-back
iommu/amd: Don't set pasid_state->mm to NULL in unbind_pasid
iommu/exynos: Select ARM_DMA_USE_IOMMU
iommu/vt-d: Exclude devices using RMRRs from IOMMU API domains
iommu/omap: Remove platform data da_start and da_end fields
ARM: omap: Don't set iommu pdata da_start and da_end fields
iommu/omap: Remove virtual memory manager
iommu/vt-d: Fix issue in computing domain's iommu_snooping flag
iommu/vt-d: Introduce helper function iova_size() to improve code readability
iommu/vt-d: Introduce helper domain_pfn_within_range() to simplify code
iommu/vt-d: Simplify intel_unmap_sg() and kill duplicated code
iommu/vt-d: Change iommu_enable/disable_translation to return void
iommu/vt-d: Simplify include/linux/dmar.h
iommu/vt-d: Avoid freeing virtual machine domain in free_dmar_iommu()
iommu/vt-d: Fix possible invalid memory access caused by free_dmar_iommu()
iommu/vt-d: Allocate dynamic domain id for virtual domains only
...
Pull ARM updates from Russell King:
"Included in this update:
- perf updates from Will Deacon:
The main changes are callchain stability fixes from Jean Pihet and
event mapping and PMU name rework from Mark Rutland
The latter is preparatory work for enabling some code re-use with
arm64 in the future.
- updates for nommu from Uwe Kleine-König:
Two different fixes for the same problem making some ARM nommu
configurations not boot since 3.6-rc1. The problem is that
user_addr_max returned the biggest available RAM address which
makes some copy_from_user variants fail to read from XIP memory.
- deprecate legacy OMAP DMA API, in preparation for it's removal.
The popular drivers have been converted over, leaving a very small
number of rarely used drivers, which hopefully can be converted
during the next cycle with a bit more visibility (and hopefully
people popping out of the woodwork to help test)
- more tweaks for BE systems, particularly with the kernel image
format. In connection with this, I've cleaned up the way we
generate the linker script for the decompressor.
- removal of hard-coded assumptions of the kernel stack size, making
everywhere depend on the value of THREAD_SIZE_ORDER.
- MCPM updates from Nicolas Pitre.
- Make it easier for proper CPU part number checks (which should
always include the vendor field).
- Assembly code optimisation - use the "bx" instruction when
returning from a function on ARMv6+ rather than "mov pc, reg".
- Save the last kernel misaligned fault location and report it via
the procfs alignment file.
- Clean up the way we create the initial stack frame, which is a
repeated pattern in several different locations.
- Support for 8-byte get_user(), needed for some DRM implementations.
- mcs locking from Will Deacon.
- Save and restore a few more Cortex-A9 registers (for errata
workarounds)
- Fix various aspects of the SWP emulation, and the ELF hwcap for the
SWP instruction.
- Update LPAE logic for pte_write and pmd_write to make it more
correct.
- Support for Broadcom Brahma15 CPU cores.
- ARM assembly crypto updates from Ard Biesheuvel"
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (53 commits)
ARM: add comments to the early page table remap code
ARM: 8122/1: smp_scu: enable SCU standby support
ARM: 8121/1: smp_scu: use macro for SCU enable bit
ARM: 8120/1: crypto: sha512: add ARM NEON implementation
ARM: 8119/1: crypto: sha1: add ARM NEON implementation
ARM: 8118/1: crypto: sha1/make use of common SHA-1 structures
ARM: 8113/1: remove remaining definitions of PLAT_PHYS_OFFSET from <mach/memory.h>
ARM: 8111/1: Enable erratum 798181 for Broadcom Brahma-B15
ARM: 8110/1: do CPU-specific init for Broadcom Brahma15 cores
ARM: 8109/1: mm: Modify pte_write and pmd_write logic for LPAE
ARM: 8108/1: mm: Introduce {pte,pmd}_isset and {pte,pmd}_isclear
ARM: hwcap: disable HWCAP_SWP if the CPU advertises it has exclusives
ARM: SWP emulation: only initialise on ARMv7 CPUs
ARM: SWP emulation: always enable when SMP is enabled
ARM: 8103/1: save/restore Cortex-A9 CP15 registers on suspend/resume
ARM: 8098/1: mcs lock: implement wfe-based polling for MCS locking
ARM: 8091/2: add get_user() support for 8 byte types
ARM: 8097/1: unistd.h: relocate comments back to place
ARM: 8096/1: Describe required sort order for textofs-y (TEXT_OFFSET)
ARM: 8090/1: add revision info for PL310 errata 588369 and 727915
...
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
According to the comment “restore_es3: applies to 34xx >= ES3.0" in
"arch/arm/mach-omap2/sleep34xx.S”, omap3_restore_es3 should be used
if the revision of an OMAP34xx is ES3.1.2.
Signed-off-by: Jeremy Vial <jvial@adeneo-embedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modify OMAP PLL rate rounding function to round to the exact rate requested
or the next one below it. This is intended to resolve some DSS problems.
Basic build, boot, and PM test results are available here:
http://www.pwsan.com/omap/testlogs/clock-b-v3.17/20140725061121/
This resolves a nontrivial conflict against a bug fix
in another branch.
Conflicts:
arch/arm/mach-exynos/pm.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge non-urgent omap fixes from Tony Lindgren:
Fixes for omaps that were not considered urgent enough for the
rc series. Mostly a fix for GPMC allocation and omap5 ABB
(Adaptive Body Bias).
* tag 'omap-for-v3.17/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()
omap16xx: Removes fixme no longer needed in ocpi_enable()
ARM: dts: OMAP5: Add device nodes for ABB
ARM: omap2+: usb-tusb6010.c: Cleaning up variable is set more than once
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "SoC related changes for omaps for v3.17 merge window"
from Tony Lindgren:
- Add device tree and hwmod data for various devices
for new SoCs
- Remove legacy mailbox hwmod data that's no longer
needed for SoCs that are DT only. Note that this may
cause a minor merge conflict in mach-omap2/devices.c
with omap_init_mbox() and omap_init_hdmi_audio(), both
are legacy code that is getting removed
* tag 'omap-for-v3.17/soc-new' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Add data for RTC
arm: dra7xx: Add hwmod data for MDIO and CPSW
arm: dra7xx: Add hwmod data for pcie1 and pcie2 subsystems
arm: dra7xx: Add hwmod data for pcie1 phy and pcie2 phy
ARM: DRA7: hwmod: Add OCP2SCP3 module
ARM: DRA7: hwmod: remove interrupts for DMA
ARM: OMAP2+: DMA: remove requirement of irq for platform-dma driver
ARM: AM33xx: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP4: hwmod_data: Remove legacy mailbox addrs
ARM: OMAP2: hwmod_data: Remove legacy mailbox data and addrs
ARM: OMAP2+: Avoid mailbox legacy device creation for DT-boot
ARM: DRA7: hwmod_data: Add mailbox hwmod data
ARM: dts: DRA7: Add mailbox nodes
ARM: dts: AM4372: Correct mailbox node data
ARM: dts: AM33xx: Add mailbox node
ARM: dts: OMAP4: Add mailbox node
ARM: dts: OMAP2+: Add mailbox fifo and user information
ARM: AM43xx: hwmod: add DSS hwmod data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Change the behavior of omap2_dpll_round_rate() to round to either the
exact rate requested, or the next lowest rate that the clock is able to
provide.
This is not an ideal fix, but is intended to provide a relatively safe
way for drivers to set PLL rates, until a better solution can be
implemented.
For the time being, omap3_noncore_dpll_set_rate() is still allowed to
set its rate to something other than what the caller requested; but will
warn when this occurs.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds bch8 ecc software fallback which is mostly used by
omap3s because they lack hardware elm support.
Fixes: 0611c41934 (ARM: OMAP2+: gpmc:
update gpmc_hwecc_bch_capable() for new platforms and ECC schemes)
Cc: <stable@vger.kernel.org> # 3.15.x+
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the OPP layer is a kernel library which has been converted to be
directly selectable by its callers rather than user selectable and
requiring architectures to enable it explicitly the ARCH_HAS_OPP symbol
has become redundant and can be removed. Do so.
Signed-off-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add hwmod data for RTC
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Added hwmod data for pcie1 and pcie2 phy present in DRA7xx SOC.
Also added the missing CLKCTRL OFFSET macro and CONTEXT OFFSET macro
for pcie1 phy and pcie2 phy.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This module is needed for the SATA and PCIe PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DMA interrupts are now available in of, and the definitions are
duplicates in hwmod. This prevents us from dynamically allocating
interrupt resources for dma from devicetree.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we have currently 2 DMA drivers that try to co-exist.
drivers/dma/omap-dma.c which registers it's own IRQ and is device tree
aware and uses arch/arm/plat-omap/dma.c instance created by
arch/arm/mach-omap2/dma.c to maintain channel usage (omap_request_dma).
Currently both try to register interrupts and mach-omap2/plat-omap dma.c
attempts to use the IRQ number registered by hwmod to register it's own
interrupt handler.
Now, there is no reasonable way of static allocating DMA irq in GIC
SPI when we use crossbar. However, since the dma_chan structure is
freed as a result of IRQ not being present due to devm allocation,
maintaining information of channel by platform code fails at a later
point in time when that region of memory is reused.
So, if hwmod does not indicate an IRQ number, then, assume that
dma-engine will take care of the interrupt handling.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "omap soc clean-up for v3.17 merge window" from Tony Lindgren:
SoC specific omap clean-up for v3.17 merge window:
- Changes to PRM and clock related code to help move
things to drivers
- Removal of unused ctrl module defines that no longer
are needed with things moving to .dts files and
drivers
* tag 'omap-for-v3.17/soc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: OMAP2+: clock/interface: remove some headers from clkt_iclk.c file
ARM: OMAP2+: clock/dpll: remove unused header includes from dpll3xxx.c
ARM: OMAP2+: clock/dpll: remove unused header includes from clkt_dpll.c
ARM: OMAP2+: clock/interface: add a clk_features definition for idlest value
ARM: OMAP2+: clock/dpll: add jitter correction behind clk_features
ARM: OMAP2+: clock/dpll: convert bypass check to use clk_features
ARM: OMAP2+: clock/dpll: add private API for checking if DPLL is in bypass
ARM: OMAP2+: clock: add fint values to the ti_clk_features struct
ARM: OMAP2+: clock: introduce ti_clk_features flags
ARM: OMAP4+: dpll44xx: remove cm-regbits-44xx.h and clock44xx.h includes
ARM: OMAP4+: dpll: remove cpu_is_omap44xx checks
ARM: OMAP4+: clock: remove DEFINE_CLK_OMAP_HSDIVIDER macro
ARM: OMAP4: Ctrl module register define diet
ARM: OMAP3: control: isolate control module init to its own function
ARM: OMAP3: PRM: move modem reset and iva2 idle to PRM driver
ARM: OMAP3: control: add API for setting up the modem pads
ARM: OMAP3: PRM: move PRM init code from PM core to the driver
ARM: OMAP24xx: PRM: add API for clearing wakeup status bits
ARM: OMAP3: PRM: add API for saving PRM scratchpad contents
ARM: OMAP3: PRM: add API for checking and clearing cold reset status
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv6 and greater introduced a new instruction ("bx") which can be used
to return from function calls. Recent CPUs perform better when the
"bx lr" instruction is used rather than the "mov pc, lr" instruction,
and this sequence is strongly recommended to be used by the ARM
architecture manual (section A.4.1.1).
We provide a new macro "ret" with all its variants for the condition
code which will resolve to the appropriate instruction.
Rather than doing this piecemeal, and miss some instances, change all
the "mov pc" instances to use the new macro, with the exception of
the "movs" instruction and the kprobes code. This allows us to detect
the "mov pc, lr" case and fix it up - and also gives us the possibility
of deploying this for other registers depending on the CPU selection.
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Stephen Warren <swarren@nvidia.com> # Tegra Jetson TK1
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> # mioa701_bootresume.S
Tested-by: Andrew Lunn <andrew@lunn.ch> # Kirkwood
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Tony Lindgren <tony@atomide.com> # OMAPs
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com> # Armada XP, 375, 385
Acked-by: Sekhar Nori <nsekhar@ti.com> # DaVinci
Acked-by: Christoffer Dall <christoffer.dall@linaro.org> # kvm/hyp
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com> # PXA3xx
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> # Xen
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # ARMv7M
Tested-by: Simon Horman <horms+renesas@verge.net.au> # Shmobile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead, copy the used constants from the header file to the source file.
This allows the code to be migrated under drivers folder where we don't
have access to the OMAP specific header files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some of the machine specific header includes are no longer used, so remove
these from the source file. This allows migration of the file under clock
driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
