IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
nv50_display_create() is declared in another header, along with
a couple of declarations that are now outdated:
drivers/gpu/drm/nouveau/dispnv50/disp.c:2517:1: error: no previous prototype for 'nv50_display_create'
Fixes: ba801ef068c1 ("drm/nouveau/kms: display destroy/init/fini hooks can be static")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230417210329.2469722-1-arnd@kernel.org
Implement support for DSI clock and data lane DN/DP polarity swap by
means of decoding 'lane-polarities' DT property. The controller does
support DN/DP swap of clock lane and all data lanes, the controller
does not support polarity swap of individual data lane bundles, add
a check which verifies all data lanes have the same polarity.
This has been validated on an imx8mm board that actually has the MIPI DSI
clock lanes inverted.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-2-festevam@gmail.com
The Samsung DSIM IP block allows the inversion of the clock and
data lanes.
Add an optional property called 'lane-polarities' that describes the
polarities of the MIPI DSI clock and data lanes.
This property is useful for properly describing the hardware when the
board designer decided to switch the polarities of the MIPI DSI
clock and/or data lanes.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-1-festevam@gmail.com
Initial driver for S6D7AA0-controlled panels. Currently, the following
panels are supported:
- S6D7AA0-LSL080AL02 (Samsung Galaxy Tab 3 8.0)
- S6D7AA0-LSL080AL03 (Samsung Galaxy Tab A 8.0 2015)
- S6D7AA0-LTL101AT01 (Samsung Galaxy Tab A 9.7 2015)
It should be possible to extend this driver to work with other panels
using this IC.
Tested-by: Nikita Travkin <nikita@trvn.ru> #ltl101at01
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519170354.29610-3-aweber.kernel@gmail.com
Add bindings for the S6D7AA0 LCD panel controller, including the
S6D7AA0-LSL080AL02 panel used in the Samsung Galaxy Tab 3 8.0 family
of tablets, and the S6D7AA0-LSL080AL03 and S6D7AA0-LTL101AT01 panels
used in the Samsung Galaxy Tab A 8.0 and 9.7 2015.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230519170354.29610-2-aweber.kernel@gmail.com
Rename drm_sched_wakeup() to drm_sched_wakeup_if_canqueue() since the former
is misleading, as it wakes up the GPU scheduler _only if_ more jobs can be
queued to the underlying hardware.
This distinction is important to make, since the wake conditional in the GPU
scheduler thread wakes up when other conditions are also true, e.g. when there
are jobs to be cleaned. For instance, a user might want to wake up the
scheduler only because there are more jobs to clean, but whether we can queue
more jobs is irrelevant.
v2: Separate "canqueue" to "can_queue". (Alex D.)
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Link: https://lore.kernel.org/r/20230517233550.377847-2-luben.tuikov@amd.com
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Rename drm_sched_ready() to drm_sched_can_queue(). "ready" can mean many
things and is thus meaningless in this context. Instead, rename to a name
which precisely conveys what is being checked.
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Link: https://lore.kernel.org/r/20230517233550.377847-1-luben.tuikov@amd.com
Update the names of the fb_mem*() helpers to be consistent with their
regular counterparts. Hence, fb_memset() now becomes fb_memset_io(),
fb_memcpy_fromfb() now becomes fb_memcpy_fromio() and fb_memcpy_tofb()
becomes fb_memcpy_toio(). No functional changes.
v6:
* update new file fb_io_fops.c
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-8-tzimmermann@suse.de
Implement framebuffer I/O helpers, such as fb_read*() and fb_write*(),
in the architecture's <asm/fb.h> header file or the generic one.
The common case has been the use of regular I/O functions, such as
__raw_readb() or memset_io(). A few architectures used plain system-
memory reads and writes. Sparc used helpers for its SBus.
The architectures that used special cases provide the same code in
their __raw_*() I/O helpers. So the patch replaces this code with the
__raw_*() functions and moves it to <asm-generic/fb.h> for all
architectures.
v8:
* remove garbage after commit-message tags
v6:
* fix fb_readq()/fb_writeq() on 64-bit mips (kernel test robot)
v5:
* include <linux/io.h> in <asm-generic/fb>; fix s390 build
v4:
* ia64, loongarch, sparc64: add fb_mem*() to arch headers
to keep current semantics (Arnd)
v3:
* implement all architectures with generic helpers
* support reordering and native byte order (Geert, Arnd)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-7-tzimmermann@suse.de
Replace include statements for <asm/fb.h> with <linux/fb.h>. Fixes
the coding style: if a header is available in asm/ and linux/, it
is preferable to include the header from linux/. This only affects
a few source files, most of which already include <linux/fb.h>.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-6-tzimmermann@suse.de
The code uses writel() and similar I/O-memory helpers. Include
the header file to get the declarations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-5-tzimmermann@suse.de
The code uses readl() and writel(). Include the header file to
get the declarations.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-4-tzimmermann@suse.de
Cast I/O offsets to pointers to use them with I/O functions. The I/O
functions expect pointers of type 'volatile void __iomem *', but the
offsets are plain integers. Build warnings are
../drivers/video/fbdev/hitfb.c: In function 'hitfb_accel_wait':
../arch/x86/include/asm/hd64461.h:18:33: warning: passing argument 1 of 'fb_readw' makes pointer from integer without a cast [-Wint-conversion]
18 | #define HD64461_IO_OFFSET(x) (HD64461_IOBASE + (x))
| ^~~~~~~~~~~~~~~~~~~~~~
| |
| unsigned int
../arch/x86/include/asm/hd64461.h:93:33: note: in expansion of macro 'HD64461_IO_OFFSET'
93 | #define HD64461_GRCFGR HD64461_IO_OFFSET(0x1044) /* Accelerator Configuration Register */
| ^~~~~~~~~~~~~~~~~
../drivers/video/fbdev/hitfb.c:47:25: note: in expansion of macro 'HD64461_GRCFGR'
47 | while (fb_readw(HD64461_GRCFGR) & HD64461_GRCFGR_ACCSTATUS) ;
| ^~~~~~~~~~~~~~
In file included from ../arch/x86/include/asm/fb.h:15,
from ../include/linux/fb.h:19,
from ../drivers/video/fbdev/hitfb.c:22:
../include/asm-generic/fb.h:52:57: note: expected 'const volatile void *' but argument is of type 'unsigned int'
52 | static inline u16 fb_readw(const volatile void __iomem *addr)
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
This patch only fixes the build warnings. It's not clear if the I/O
offsets can legally be passed to the I/O helpers. It was apparently
broken in 2007 when custom inw()/outw() helpers got removed by
commit 34a780a0afeb ("sh: hp6xx pata_platform support."). Fixing the
driver would require setting the I/O base address.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202305102136.eMjTSPwH-lkp@intel.com/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512102444.5438-2-tzimmermann@suse.de
DSI device registering and attaching needs to be undone upon
deregistration. This fixes module unload/load.
Fixes: bbfd3190b656 ("drm/bridge: tc358767: Add DSI-to-DPI mode support")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230517122107.1766673-1-alexander.stein@ew.tq-group.com
Make the struct ttm_device_funcs pointers const so the data can be placed in rodata.
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309123700.528641-1-jani.nikula@intel.com
There is a problem of screen shake on the old panel. So increase the
panel GOP component pull-down circuit size in hardware, and update the
initialization code at the same time. The new initialization code mainly
modifles the following.
a)adjusted for GOP timing. When Display sleep in, raise all GOP signals
to VGHO and then drop to GND.
b)Increased the Vertical back Porch and Vertical pulse width, so need to
update vsync_end and vtotal and CLK in drm_display_mode.
Signed-off-by: Cong Yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[dianders: fixed spelling mistake in subject]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230509025153.1321446-1-yangcong5@huaqin.corp-partner.google.com
There is no need to exclusively set the .owner member of the struct
device_driver when defining the platform_driver struct. The Linux core
takes care of setting the .owner member as part of the call to
module_platform_driver() helper function.
Issue identified using the platform_no_drv_owner.cocci Coccinelle
semantic patch as:
drivers/gpu/drm/bridge/samsung-dsim.c:1957:6-11: No need to set .owner here.
The core will do it.
No functional changes are intended.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZF9igb/nvL6GRBsq@yoga
The TC358867/TC9595 devices are compatible with the predecessor TC358767.
Document compatible strings for the new devices, so they can be discerned
in board DTs. Update the title to match description in the process.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515162033.66986-1-marex@denx.de
Currently, the pixel conversion isn't rounding the fixed-point values
before assigning it to the RGB coefficients, which is causing the IGT
pixel-format tests to fail. So, use the drm_fixp2int_round() fixed-point
helper to round the values when assigning it to the RGB coefficients.
Tested with igt@kms_plane@pixel-format and igt@kms_plane@pixel-format-source-clamping.
[v2]:
* Use drm_fixp2int_round() to fix the pixel conversion instead of
casting the values to s32 (Melissa Wen).
Fixes: 89b03aeaef16 ("drm/vkms: fix 32bit compilation error by replacing macros")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512104044.65034-2-mcanal@igalia.com
Create a new fixed-point helper to allow us to return the rounded value
of our fixed point value.
[v2]:
* Create the function drm_fixp2int_round() (Melissa Wen).
[v3]:
* Use drm_fixp2int() instead of shifting manually (Arthur Grillo).
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Arthur Grillo <arthurgrillo@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512104044.65034-1-mcanal@igalia.com
For "boe,tv105wum-nw0" this special panel, it is stipulated in
the panel spec that MIPI needs to keep the LP11 state before
the lcm_reset pin is pulled high.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515094955.15982-3-shuijing.li@mediatek.com
Reduce the delay after LCM reset by removing an extra delay in the
initialization commands array. The required delay of at least 6ms after
reset is guaranteed by boe_panel_prepare().
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515094955.15982-2-shuijing.li@mediatek.com
This is a leftover from an early iteration of the driver when it was still
named ssd1307 instead of ssd130x. Change it for consistency with the rest.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512120232.304603-1-javierm@redhat.com
Consider a configuration like this:
1, efifb (or simpledrm) is built-in;
2, a native display driver (such as radeon) is also built-in.
As Javier said, this is not a common configuration (the native display
driver is usually built as a module), but it can happen and cause some
trouble.
In this case, since efifb, radeon and sysfb are all in device_initcall()
level, the order in practise is like this:
efifb registered at first, but no "efi-framebuffer" device yet. radeon
registered later, and /dev/fb0 created. sysfb_init() comes at last, it
registers "efi-framebuffer" and then causes an error message "efifb: a
framebuffer is already registered". Make sysfb_init() to be subsys_
initcall_sync() can avoid this. And Javier Martinez Canillas is trying
to make a more general solution in commit 873eb3b11860 ("fbdev: Disable
sysfb device registration when removing conflicting FBs").
However, this patch still makes sense because it can make the screen
display as early as possible (We cannot move to subsys_initcall, since
sysfb_init() should be executed after PCI enumeration).
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220704011704.1418055-1-chenhuacai@loongson.cn
Drop sharp_nt_panel_disable() and sharp_nt_panel_enable(), which bear no
useful code. Also drop sharp_nt_panel::enable and sharp_nt_panel::mode
fields which also provide no use now.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507172639.2320934-2-dmitry.baryshkov@linaro.org
Using current settings causes panel flickering on APQ8074 dragonboard.
Adjust panel settings to follow the vendor-provided mode. This also
enables MIPI_DSI_MODE_VIDEO_SYNC_PULSE, which is also specified by the
vendor dtsi for the mentioned dragonboard.
Fixes: ee0172383190 ("drm/panel: Add Sharp LS043T1LE01 MIPI DSI panel")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507172639.2320934-1-dmitry.baryshkov@linaro.org
Smatch reports:
drivers/gpu/drm/sun4i/sun4i_tcon.c:805 sun4i_tcon_init_clocks() warn:
'tcon->clk' from clk_prepare_enable() not released on lines: 792,801.
In the function sun4i_tcon_init_clocks(), tcon->clk and tcon->sclk0 are
not disabled in the error handling, which affects the release of
these variable. Although sun4i_tcon_bind(), which calls
sun4i_tcon_init_clocks(), use sun4i_tcon_free_clocks to disable the
variables mentioned, but the error handling branch of
sun4i_tcon_init_clocks() ignores the required disable process.
To fix this issue, use the devm_clk_get_enabled to automatically
balance enable and disabled calls. As original implementation use
sun4i_tcon_free_clocks() to disable clk explicitly, we delete the
related calls and error handling that are no longer needed.
Fixes: 9026e0d122ac ("drm: Add Allwinner A10 Display Engine support")
Fixes: b14e945bda8a ("drm/sun4i: tcon: Prepare and enable TCON channel 0 clock at init")
Fixes: 8e9240472522 ("drm/sun4i: support TCONs without channel 1")
Fixes: 34d698f6e349 ("drm/sun4i: Add has_channel_0 TCON quirk")
Signed-off-by: XuDong Liu <m202071377@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230430112347.4689-1-m202071377@hust.edu.cn
While the rate of TCON0's DCLK matches dotclock for parallel and LVDS
outputs, this doesn't hold for DSI. The 'D' in DCLK actually stands for
'Data' according to Allwinner's manuals. The clock is mostly referred to
as dclk throughout this driver already anyway, so stick with that.
Signed-off-by: Roman Beranek <me@crly.cz>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230505052110.67514-4-me@crly.cz
I've been contributing to VKMS with improvements, reviews, testing and
debugging. Therefore, add myself as a co-maintainer of the VKMS driver.
Acked-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230508141038.327160-1-mairacanal@riseup.net
Add documentation for the DRM_MODE_TV_MODE_MAX enumerator to fix the
kernel-doc warning:
include/drm/drm_connector.h:204: warning: Enum value 'DRM_MODE_TV_MODE_MAX' not described in enum 'drm_connector_tv_mode'
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20230504123444.1843795-1-jani.nikula@intel.com
added documentation to drm_dev_unregister clarifying that devres managed
devices allocated with devm_drm_dev_alloc do not require calls to
drm_dev_put.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Brandon Pollack <brpol@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230425080240.3582324-1-brpol@chromium.org
Move the existing I/O read and write code for I/O memory into
the new helpers fb_cfb_read() and fb_cfb_write(). Make them the
default fp_ops. No functional changes.
In the near term, the new functions will be useful to the DRM
subsystem, which currently provides it's own implementation. It
can then use the shared code. In the longer term, it might make
sense to revise the I/O helper's default status and make them
opt-in by the driver. Systems that don't use them would not
contain the code any longer.
v2:
* add detailed commit message (Javier)
* rename fb_cfb_() to fb_io_() (Geert)
* add fixes that got lost while moving the code (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-19-tzimmermann@suse.de
Push the test for info->screen_base from fb_read() and fb_write() into
the implementations of struct fb_ops.{fb_read,fb_write}. In cases where
the driver operates on info->screen_buffer, test this field instead.
While bothi fields, screen_base and screen_buffer, are stored in the
same location, they refer to different address spaces. For correctness,
we want to test each field in exactly the code that uses it.
v2:
* also test screen_base in pvr2fb (Geert)
* also test screen_buffer in ivtvfb, arcfb, broadsheetfb,
hecubafb, metronomefb and ssd1307fb (Geert)
* give a rational for the change (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-18-tzimmermann@suse.de
The file-op entry points fb_read() and fb_write() verify that
info->state has been set to FBINFO_STATE_RUNNING. Remove the same
test from the implementations of struct fb_ops.{fb_read,fb_write}.
v2:
* also remove test from ivtvfb, braodsheetfb, hecubafb and
metronomefb (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-17-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
Since the fb_sys_{read,write}() functions operate on the latter address
space, it is wrong to use .screen_base and .screen_buffer must be used
instead. This also gets rid of all the casting needed due to not using
the correct data type.
v2:
* add detailed commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-16-tzimmermann@suse.de
Always return the number of bytes read or written within the
framebuffer. Only return an errno code if framebuffer memory
was not touched. This is the semantics required by POSIX and
makes fb_read() and fb_write() compatible with IGT tests. [1]
This bug has been fixed for fb_write() long ago by
commit 6a2a88668e90 ("[PATCH] fbdev: Fix return error of
fb_write"). The code in fb_read() and the corresponding fb_sys_()
helpers was forgotten.
It can happen that copy_{from, to}_user() only partially copies
the given buffer. Take this into account when calculating the
number of bytes.
v2:
* consider return value from copy_{from,to}_user() (Geert)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Helge Deller <deller@gmx.de>
Link: https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/blob/master/tests/fbdev.c # 1
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-15-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-14-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-13-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-12-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-11-tzimmermann@suse.de
Use info->screen_buffer when reading and writing framebuffers in
system memory. It's the correct pointer for this address space.
The struct fb_info has a union to store the framebuffer memory. This can
either be info->screen_base if the framebuffer is stored in I/O memory,
or info->screen_buffer if the framebuffer is stored in system memory.
As the driver operates on the latter address space, it is wrong to use
.screen_base and .screen_buffer must be used instead. This also gets
rid of casting needed due to not using the correct data type.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428122452.4856-10-tzimmermann@suse.de
