IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The suggested value in the mmp2 manual is wrong.
There are only 13 bits for numerator, but some suggested
value has 14 bits.
Fix the factor tabled and remove the unused items.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver supports the TI CDCE925 programmable clock synthesizer.
The chip contains two PLLs with spread-spectrum clocking support and
five output dividers. The driver only supports the following setup,
and uses a fixed setting for the output muxes:
Y1 is derived from the input clock
Y2 and Y3 derive from PLL1
Y4 and Y5 derive from PLL2
Given a target output frequency, the driver will set the PLL and
divider to best approximate the desired output.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Even if not documented in the datasheet, the Armada 370 SoC can actually
gate the CESA (crypto engine) clock.
Add an entry in the gating_desc table to be able to reference the CESA
gateclk in the crypto node.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add clock drivers for hi6220 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
We add one divider clock for hi6220 because the divider in hi6220
also has a mask bit but it doesnot obey the rule defined by flag
"CLK_DIVIDER_HIWORD_MASK", we can not get index of the mask bit by
left shift fixed bits (e.g. 16 bits), so we add this divider clock
to handle it.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Acked-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Add the header file "hi6220-clock.h" used by both
hi6220 clock driver and hi6220 device tree file.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
__init markings on function prototypes are useless, so remove
them.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bintian Wang <bintian.wang@huawei.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clocks on the Arria 10 platform is a bit different than the
Cyclone/Arria 5 platform that it should just have it's own
driver.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are 5 possible parent clocks for the SoCFPGA Arria10. Move the define
SYSMGR_SDMMC_CTRL_SET and streq() to clk.h so that the Arria clock driver
can use.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove a previously registered clock provider when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the fixed clocks of external crystal oscillators.
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[sboyd@codeaurora.org: Remove size-cells/address-cells]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
the hardware node includes both clock and reset support, so it
is named as "car".
this patch implements Flexible clocks(mux, divider, gate), Selectable
clock(mux, divider, gate), root clock(gate),leaf clock(gate), others.
it also implements the reset controller functionality.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Guo Zeng <Guo.Zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The variable init (struct clk_init_data) is allocated on the stack.
We weren't initializing the .flags field, so it contains random junk,
which can cause all kinds of interesting issues when the flags are
parsed by clk_register.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add initial clock support for Marvell PXA1928. The PXA1928 is a mobile
SOC and is similar to other MMP/PXA series of SOCs, so a lot of the
existing infrastructure is reused here.
Currently the PLLs are just fixed clocks, and not all leaf clocks are
implemented.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds the clock binding documentation for the Marvell PXA1928 SOC.
The PXA1928 has 3 clock control blocks for different subsystems of the
chip.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch shows the correct information for debugging when fail
to set clock rate because original error message shows the error
value instead of current clock rate.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Having this Kconfig sourced outside the clk menu means the option
is under the "Device Drivers" menu instead of the "Common Clock
Framework" menu. Move it so that the bcm clock config options are
in the right place.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-u300.c:1175:13: warning: symbol 'u300_clk_init' was not declared. Should it be static?
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-moxart.c:18:13: warning: symbol 'moxart_of_pll_clk_init' was not declared. Should it be static?
drivers/clk/clk-moxart.c:56:13: warning: symbol 'moxart_of_apb_clk_init' was not declared. Should it be static?
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-xgene.c:77:43: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/clk-xgene.c:77:43: expected void *csr
drivers/clk/clk-xgene.c:77:43: got void [noderef] <asn:2>*
...
drivers/clk/clk-xgene.c: In function ‘xgene_clk_enable’:
drivers/clk/clk-xgene.c:237:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
drivers/clk/clk-xgene.c:248:3: warning: format ‘%LX’ expects argument of type ‘long long unsigned int’, but argument 4 has type ‘phys_addr_t’ [-Wformat]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/mmp/clk-apbc.c:118:16: warning: symbol 'clk_apbc_ops' was not declared. Should it be static?
drivers/clk/mmp/clk-apmu.c:64:16: warning: symbol 'clk_apmu_ops' was not declared. Should it be static?
Cc: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/versatile/clk-sp810.c:159:29: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:29: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:29: right side has type int
drivers/clk/versatile/clk-sp810.c:159:53: error: incompatible types for operation (<=)
drivers/clk/versatile/clk-sp810.c:159:53: left side has type char const *<noident>
drivers/clk/versatile/clk-sp810.c:159:53: right side has type int
drivers/clk/versatile/clk-sp810.c:138:13: warning: symbol 'clk_sp810_of_setup' was not declared. Should it be static?
Acked: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/ti/clk.c:125:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:125:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:125:31: got void *
drivers/clk/ti/clk.c:132:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:132:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:132:31: got void *
drivers/clk/ti/dpll.c:180:14: warning: symbol '_get_reg' was not declared. Should it be static?
drivers/clk/ti/fapll.c:624:32: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:625:31: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:630:40: warning: Using plain integer as NULL pointer
drivers/clk/ti/clk-dra7-atl.c:158:22: warning: symbol 'atl_clk_ops' was not declared. Should it be static?
drivers/clk/ti/clk-dra7-atl.c:170:39: warning: Using plain integer as NULL pointer
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/st/clkgen-mux.c:134:4: warning: symbol 'clkgena_divmux_get_parent' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:171:15: warning: symbol 'clkgena_divmux_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:218:12: warning: symbol 'clk_register_genamux' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:388:13: warning: symbol 'st_of_clkgena_divmux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:488:13: warning: symbol 'st_of_clkgena_prediv_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:625:13: warning: symbol 'st_of_clkgen_mux_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-mux.c:702:13: warning: symbol 'st_of_clkgen_vcc_setup' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:273:15: warning: symbol 'recalc_stm_pll800c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:300:15: warning: symbol 'recalc_stm_pll1600c65' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:324:15: warning: symbol 'recalc_stm_pll3200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:346:15: warning: symbol 'recalc_stm_pll1200c32' was not declared. Should it be static?
drivers/clk/st/clkgen-pll.c:565:19: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:565:19: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:565:19: got void *
drivers/clk/st/clkgen-pll.c:576:18: warning: incorrect type in assignment (different address spaces)
drivers/clk/st/clkgen-pll.c:576:18: expected void [noderef] <asn:2>*reg
drivers/clk/st/clkgen-pll.c:576:18: got void *
drivers/clk/st/clkgen-pll.c:693:53: warning: incorrect type in argument 2 (different address spaces)
drivers/clk/st/clkgen-pll.c:693:53: expected void *[noderef] <asn:2>reg
drivers/clk/st/clkgen-pll.c:693:53: got void [noderef] <asn:2>*[assigned] pll_base
drivers/clk/st/clkgen-fsyn.c:495:5: warning: symbol 'clk_fs660c32_vco_get_rate' was not declared. Should it be static?
drivers/clk/st/clkgen-fsyn.c:522:5: warning: symbol 'clk_fs660c32_vco_get_params' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:119:15: warning: symbol 'flexgen_recalc_rate' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:177:12: warning: symbol 'clk_register_flexgen' was not declared. Should it be static?
drivers/clk/st/clk-flexgen.c:263:13: warning: symbol 'st_of_flexgen_setup' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These are __iomem pointers. Mark them appropriately so we don't
get sparse errors like
drivers/clk/sirf/clk-common.c:60:16: warning: incorrect type in argument 1 (different address spaces)
drivers/clk/sirf/clk-common.c:60:16: expected void const volatile [noderef] <asn:2>*addr
drivers/clk/sirf/clk-common.c:60:16: got void *
Cc: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/shmobile/clk-emev2.c:37:14: warning: symbol 'smu_base' was not declared. Should it be static?
Cc: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/samsung/clk-exynos5260.c:138:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:328:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:392:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:494:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:583:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:644:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:779:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:898:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:962:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1018:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1165:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1373:40: warning: Using plain integer as NULL pointer
drivers/clk/samsung/clk-exynos5260.c:1829:40: warning: Using plain integer as NULL pointer
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/hisilicon/clk-hix5hd2.c:255:13: warning: symbol 'hix5hd2_clk_register_complex' was not declared. Should it be static?
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/berlin/berlin2-pll.c:94:12: warning: symbol 'berlin2_pll_register' was not declared. Should it be static?
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This list doesn't look to be used. Let's remove it and any
associated code that would be manipulating this list. This also
silences this error:
drivers/clk/bcm/clk-kona-setup.c:24:1: warning: symbol 'ccu_list' was not declared. Should it be static?
Reviewed-by: Alex Elder <elder@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk-max-gen.c:82:16: warning: symbol 'max_gen_clk_ops' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:109:5: warning: symbol 'max_gen_clk_probe' was not declared. Should it be static?
drivers/clk/clk-max-gen.c:183:5: warning: symbol 'max_gen_clk_remove' was not declared. Should it be static?
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
drivers/clk/clk.c:2700:5: warning: symbol '__clk_get' was not declared. Should it be static?
drivers/clk/clk.c:2713:6: warning: symbol '__clk_put' was not declared. Should it be static?
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This function is marked as __init, so exposing it to modules
doesn't make any sense and it isn't used by modules anyway.
drivers/clk/clk-gpio-gate.c:192:13: warning: symbol 'of_gpio_gate_clk_setup' was not declared. Should it be static?
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Printing an error on kmalloc() failures is unnecessary. Remove
the print and use *ptr in sizeof() for future-proof code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_clk_get_from_provider() returns ERR_PTR on failure. The
dra7-atl-clock driver was not checking its return value and
immediately used it in __clk_get_hw(). __clk_get_hw()
dereferences supplied clock, if it is not NULL, so in that case
it would dereference an ERR_PTR.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the following compiler warning:
drivers/clk/clk-axm5516.c: In function 'axmclk_probe':
drivers/clk/clk-axm5516.c:559:2: warning: format '%u' expects argument of type 'unsigned int', but argument 2 has type 'size_t' [-Wformat=]
pr_info("axmclk: supporting %u clocks\n", num_clks);
^
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_io_request_and map returns an error pointer, but the current code assumes
that on error the returned pointer will be NULL.
Obviously, that makes the check completely useless. Change the test to actually
check for the proper error code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently Documentation/clk.txt describes an obsolete techinique to
statically define struct clk objects.
This capability was removed by b09d6d991025("clk: remove clk-private.h")
and is no longer supported. The documentation describing the feature should
be removed.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The binding uses assigned-clock-parents when it should use
assigned-clock-rates. Furthermore, the part that describes how
they relate to the assigned-clocks property is not clear about
what is related. Correct and clarify this part of the binding.
Reported-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
MS6 and MS7 do not have the MSx_P3 field. Do the 'params.p3 == 0'
check for MS0-M5 only. See [AN619, p. 6] for details.
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The divider calculation for multisynth 6 and 7 differs from the
calculation for multisynth 0-5.
For MS6 and MS7, set MSx_P1 directly, MSx_P1=divide value
[AN619, p. 6].
Referenced document:
[AN619] Manually Generating an Si5351 Register Map, Rev. 0.4
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
When registering clk-si5351 by platform_data, we should not pass struct clk
for the reference clocks. Drop struct clk from platform_data and rework the
driver to use devm_clk_get of named clock references.
While at it, check for at least one valid input clock and properly prepare/
enable valid reference clocks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Jean-Francois Moine <moinejf@free.fr>
Reported-by: Russell King <rmk+linux@arm.linux.org.uk>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
