IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Two deadly typos break RX and TX traffic on the VSC8502 PHY using RGMII
if phy-mode = "rgmii-id" or "rgmii-txid", and no "tx-internal-delay-ps"
override exists. The negative error code from phy_get_internal_delay()
does not get overridden with the delay deduced from the phy-mode, and
later gets committed to hardware. Also, the rx_delay gets overridden by
what should have been the tx_delay.
Fixes: dbb050d2bf ("phy: mscc: Add support for RGMII delay configuration")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230627134235.3453358-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for optional rx/tx-internal-delay-ps from devicetree.
- When rx/tx-internal-delay-ps is/are specified, these take priority
- When either is absent,
1) use 2ns for respective settings if rgmii-id/rxid/txid is/are present
2) use 0.2ns for respective settings if mode is rgmii
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All the PHY devices variants specified have the same mask and
hence can be simplified to one vendor look up for 0x00070400.
Any individual config can be identified by PHY_ID_MATCH_EXACT
in the respective structure.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Holding the struct phy_device (phydev) lock is unnecessary when
accessing phydev->interface in the PHY driver .config_init method,
which is the only place that vsc85xx_rgmii_set_skews() is called from.
The phy_modify_paged() function implements required MDIO bus level
locking, which can not be achieved by a phydev lock.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VSC8501 PHY can use the same driver implementation as the VSC8502.
Adding the PHY ID and copying the handler functions of VSC8502 is
sufficient to operate it.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com>
Fixes: d316986331 ("net: phy: mscc: add support for VSC8502")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the blamed commit, phy_ethtool_get_wol() and phy_ethtool_set_wol()
acquire phydev->lock, but the mscc phy driver implementations,
vsc85xx_wol_get() and vsc85xx_wol_set(), acquire the same lock as well,
resulting in a deadlock.
$ ip link set swp3 down
============================================
WARNING: possible recursive locking detected
mscc_felix 0000:00:00.5 swp3: Link is Down
--------------------------------------------
ip/375 is trying to acquire lock:
ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: vsc85xx_wol_get+0x2c/0xf4
but task is already holding lock:
ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dev->lock);
lock(&dev->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by ip/375:
#0: ffffd43b2a955788 (rtnl_mutex){+.+.}-{4:4}, at: rtnetlink_rcv_msg+0x144/0x58c
#1: ffff3d7e82e987a8 (&dev->lock){+.+.}-{4:4}, at: phy_ethtool_get_wol+0x3c/0x6c
Call trace:
__mutex_lock+0x98/0x454
mutex_lock_nested+0x2c/0x38
vsc85xx_wol_get+0x2c/0xf4
phy_ethtool_get_wol+0x50/0x6c
phy_suspend+0x84/0xcc
phy_state_machine+0x1b8/0x27c
phy_stop+0x70/0x154
phylink_stop+0x34/0xc0
dsa_port_disable_rt+0x2c/0xa4
dsa_slave_close+0x38/0xec
__dev_close_many+0xc8/0x16c
__dev_change_flags+0xdc/0x218
dev_change_flags+0x24/0x6c
do_setlink+0x234/0xea4
__rtnl_newlink+0x46c/0x878
rtnl_newlink+0x50/0x7c
rtnetlink_rcv_msg+0x16c/0x58c
Removing the mutex_lock(&phydev->lock) calls from the driver restores
the functionality.
Fixes: 2f987d4866 ("net: phy: Add locks to ethtool functions")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230314153025.2372970-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Following 1b16b3fdf6 ("net: phy: mscc: macsec: clear encryption keys when freeing a flow"),
go one step further and instead of calling memzero_explicit on the key
when freeing a flow, simply not copy the key in the first place as it's
only used when a new flow is set up.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aaab73f8fb ("macsec: clear encryption keys from the stack after
setting up offload") made sure to clean encryption keys from the stack
after setting up offloading, but the MSCC PHY driver made a copy, kept
it in the flow data and did not clear it when freeing a flow. Fix this.
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove checks on the prepare phase as it is now unused by the MACsec
core implementation.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for removing the MACsec h/w offloading preparation phase,
make it a no-op in the MSCC phy driver.
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver requires firmware so define MODULE_FIRMWARE so that modinfo
provides the details.
Fixes: fa164e40c5 ("net: phy: mscc: split the driver into separate files")
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Link: https://lore.kernel.org/r/20220316151835.88765-1-juergh@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Radu Pirea <radu-nicolae.pirea@oss.nxp.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Don't populate arrays on the stack but instead them static const.
Makes the object code smaller by 280 bytes.
Before:
text data bss dec hex filename
24142 4368 192 28702 701e ./drivers/net/phy/mscc/mscc_ptp.o
After:
text data bss dec hex filename
23830 4400 192 28422 6f06 ./drivers/net/phy/mscc/mscc_ptp.o
(gcc version 10.2.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210801070155.139057-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The key length used to store the macsec key was set to MACSEC_KEYID_LEN
(16), which is an issue as:
- This was never meant to be the key length.
- The key length can be > 16.
Fix this by using MACSEC_MAX_KEY_LEN instead (the max length accepted in
uAPI).
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Reported-by: Lior Nahmanson <liorna@nvidia.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch releases coma mode for VSC8584 as done for VSC8514 in
commit ca0d7fd0a5 ("net: phy: mscc: coma mode disabled for VSC8514")
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced 'FOJI' serdes calibration in commit 85e97f0b98
("net: phy: mscc: improved serdes calibration applied to VSC8514")
Now including the VSC8584 family.
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced LCPLL reset in
commit d15e08d9fb82 ("net: phy: mscc: adding LCPLL reset to VSC8514").
Now applying this reset to the VSC8584 phy familiy.
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY.")
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'coma mode' (configurable through sw or hw) provides an
optional feature that may be used to control when the PHYs become active.
The typical usage is to synchronize the link-up time across
all PHY instances. This patch releases coma mode if not done by hardware,
otherwise the phys will not link-up.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IB serdes calibration algorithm (performed by the onboard 8051)
has proven to be unstable for the VSC8514 QSGMII phy.
A new algorithm has been developed based on
'Frequency-offset Jittered-Injection' or 'FoJi' method which solves
all known issues. This patch disables the 8051 algorithm and
replaces it with the new FoJi algorithm.
The calibration is now performed in a new file (mscc_serdes.c),
which can act as an placeholder for future serdes configurations.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At Power-On Reset, transients may cause the LCPLL to lock onto a
clock that is momentarily unstable. This is normally seen in QSGMII
setups where the higher speed 6G SerDes is being used.
This patch adds an initial LCPLL Reset to the PHY (first instance)
to avoid this issue.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use recently introduced PTP_MSGTYPE_SYNC and PTP_MSGTYPE_DELAY_REQ
defines instead of a driver internal enumeration.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Condition !A || A && B is equivalent to !A || B.
Generated by: scripts/coccinelle/misc/excluded_middle.cocci
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Reviewed-by: Antoine Tenart <atenart@kernel.org>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2011161633240.2682@hadrien
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only usage of vsc8584_macsec_ops is to assign its address to the
macsec_ops field in the phydev struct, which is a const pointer. Make it
const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of spelling mistakes in comment text. Fix these.
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/mscc/mscc_ptp.c:1496:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 7d272e63e0 ("net: phy: mscc: timestamping and PHC support")
CC: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
All PHY read and write return values are checked for errors in
vsc8514_config_init and vsc8584_config_init, except for one. Fix this.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the middle of vsc8584_config_init and vsc8514_config_init, the page
is set to 'standard'. This is the default value, and the page isn't set
to another value before. Those pages configuration can be safely
removed.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vsc8584_config_init and vsc8514_config_init, the base page is set
to 'GPIO', configuration is done, and the page is never explicitly
restored to the standard page. No bug was triggered as it turns out
helpers called in those config_init functions do modify the base page,
and set it back to standard. But that is dangerous and any modification
to those functions would introduce bugs. This patch fixes this, to
improve maintenance, by restoring the base page to 'standard' once
'GPIO' accesses are completed.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves the MSCC driver by using the provided
phy_lock_mdio_bus and phy_unlock_mdio_bus helpers instead of locking and
unlocking the MDIO bus lock directly. The patch is only cosmetic but
should improve maintenance and consistency.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a typo in a comment, s/Ths/This/. The patch is cosmetic
only.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following error was reported by smatch:
vsc85xx_ts_read_csr() error: uninitialized symbol 'blk_hw'.
In practice this is very unlikely, as all the block identifiers given to
this functions are handled and described in an enum. The smatch error is
fixed by doing what is already done in vsc85xx_ts_write_csr: using the
"PROCESSOR" block by default.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On vsc8584_ptp_init failure we jump to the 'err' label, which unlocks
the MDIO bus lock. But vsc8584_ptp_init isn't called with the MDIO bus
lock taken, which could result in a double unlock. Fix this.
Fixes: ab2bf93393 ("net: phy: mscc: 1588 block initialization")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings when building MACsec
support in the MSCC PHY driver.
mscc_macsec.c:393:42: warning: cast from restricted sci_t
mscc_macsec.c:395:42: warning: restricted sci_t degrades to integer
mscc_macsec.c:402:42: warning: restricted __be16 degrades to integer
mscc_macsec.c:608:34: warning: cast from restricted sci_t
mscc_macsec.c:610:34: warning: restricted sci_t degrades to integer
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skcipher API dynamically instantiates the transformation object
on request that implements the requested algorithm optimally on the
given platform. This notion of optimality only matters for cases like
bulk network or disk encryption, where performance can be a bottleneck,
or in cases where the algorithm itself is not known at compile time.
In the mscc case, we are dealing with AES encryption of a single
block, and so neither concern applies, and we are better off using
the AES library interface, which is lightweight and safe for this
kind of use.
Note that the scatterlist API does not permit references to buffers
that are located on the stack, so the existing code is incorrect in
any case, but avoiding the skcipher and scatterlist APIs entirely is
the most straight-forward approach to fixing this.
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Fixes: 28c5107aa9 ("net: phy: mscc: macsec support")
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PHC and timestamping operations for the MSCC
PHY. PTP 1-step and 2-step modes are supported, over Ethernet and UDP.
To get and set the PHC time, a GPIO has to be used and changes are only
retrieved or committed when on a rising edge. The same GPIO is shared by
all PHYs, so the granularity of the lock protecting it has to be
different from the ones protecting the 1588 registers (the VSC8584 PHY
has 2 1588 blocks, and a single load/save pin).
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the first parts of the 1588 support in the MSCC PHY,
with registers definition and the 1588 block initialization.
Those PHYs are distributed in hardware packages containing multiple
times the PHY. The VSC8584 for example is composed of 4 PHYs. With
hardware packages, parts of the logic is usually common and one of the
PHY has to be used for some parts of the initialization. Following this
logic, the 1588 blocks of those PHYs are shared between two PHYs and
accessing the registers has to be done using the "base" PHY of the
group. This is handled thanks to helpers in the PTP code (and locks).
We also need the MDIO bus lock while performing a single read or write
to the 1588 registers as the read/write are composed of multiple MDIO
transactions (and we don't want other threads updating the page).
Co-developed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
