IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Ido Schimmel says:
====================
mlxsw: Preparation for RTNL removal
The driver currently acquires RTNL in its route insertion path, which
contributes to very large control plane latencies. This patch set
prepares mlxsw for RTNL removal from its route insertion path in a
follow-up patch set.
Patches #1-#2 protect shared resources - KVDL and counter pool - with
their own locks. All allocations of these resources are currently
performed under RTNL, so no locks were required.
Patches #3-#7 ensure that updates to mirroring sessions only take place
in case there are active mirroring sessions. This allows us to avoid
taking RTNL when it is unnecessary, as updating of the mirroring
sessions must be performed under RTNL for the time being.
Patches #8-#10 replace the use of APIs that assume that RTNL is taken
with their RCU counterparts. Specifically, patches #8 and #9 replace
__in_dev_get_rtnl() with __in_dev_get_rcu() under RCU read-side critical
section. Patch #10 replaces __dev_get_by_index() with
dev_get_by_index_rcu().
Patches #11-#15 perform small adjustments in the code to make it easier
to later introduce a router lock instead of relying on RTNL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device supports a single VTEP whose configuration is shared between
all VXLAN tunnels.
While the shared configuration is cleared upon the destruction of the
last tunnel - in mlxsw_sp_nve_tunnel_fini() - it is set in
mlxsw_sp_nve_fid_enable(), after calling mlxsw_sp_nve_tunnel_init().
Make tunnel initialization and destruction symmetric and set the
configuration in mlxsw_sp_nve_tunnel_init().
This will later allow us to protect the shared configuration with a
lock.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch, all the callers of mlxsw_sp_rif_find_by_dev()
outside of the routing code use it to understand if a RIF exists for the
passed netdev.
Therefore, export a function to check if a RIF exists and make
mlxsw_sp_rif_find_by_dev() internal to the routing code.
This will later allow us to more easily introduce the router lock which
will also protect the RIFs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently 5 users of mlxsw_sp_rif_find_by_dev() outside of the
routing code. Only one call site actually needs to dereference the
router interface (RIF). The rest merely need to know if a RIF exists for
the provided netdev.
Convert this call site to query the needed information directly from the
routing code instead of dereferencing the RIF.
This will later allow us to replace mlxsw_sp_rif_find_by_dev() with a
function that checks if a RIF exist.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function de-associates the port-vlan from its router interface
(RIF). It is called both from the netdev notifier block and the inetaddr
notifier block that will soon hold the router lock.
Make sure that router code calls the internal version, as it will
already have the router lock held when the function is called.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function removes the FDB entry that directs the macvlan's MAC to the
router port. It is called from both the netdev notifier block and the
inetaddr notifier block that will soon hold the router lock.
Make sure that only the netdev notifier calls the exported version, so
that is will take the router lock, which will already be held by the
inetaddr notifier.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function that resolves the underlay device of the IPIP tunnel
assumes that RTNL is taken, but this will not be correct when RTNL is
removed from the route insertion path.
Convert the function to use dev_get_by_index_rcu() instead of
__dev_get_by_index() and make sure it is always called from an RCU
read-side critical section.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 addresses are deleted in an atomic context, so the driver defers
the potential teardown of the associated router interface (RIF) to a
work item that takes RTNL.
The RIF is only destroyed if the associated netdev does not have any IP
addresses (both IPv4 and IPv6). The IPv4 device ('struct in_device') is
currently fetched via __in_dev_get_rtnl() which assumes RTNL is taken.
Since RTNL is going to be removed, convert it to use __in_dev_get_rcu()
from an RCU read-side critical section.
Note that the IPv6 device ('struct inet6_dev') is fetched via
__in6_dev_get(), which does not require RTNL.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTNL is going to be removed from route insertion path, so use
__in_dev_get_rcu() from an RCU read-side critical section instead of
__in_dev_get_rtnl() which assumes RTNL is taken.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order not to needlessly schedule the work item that updates the
mirroring agents, only schedule it if there are any mirroring agents
present.
This is done by adding an atomic counter that counts the active
mirroring agents.
It is incremented / decremented whenever a mirroring agent is created /
destroyed. It is read before scheduling the work item and in the
devlink-resource occupancy callback.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch added a work item in the mirroring code that will take
care of updating the active mirroring agents in response to different
events.
Change the mirroring agents update function - mlxsw_sp_span_respin() -
to invoke this work item when called.
Therefore there is no need for callers to schedule a work item
themselves.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver updates its mirroring agents whenever it receives a
notification about an event that can affect these. For example, the
addition of a route might require the driver to change the egress port
of an ERSPAN session.
Currently, RTNL needs to be held when these agents are updates, so the
driver either:
1. Calls directly into the mirroring code, in case RTNL is held
2. Schedules a work item that will take RTNL and call into the mirroring
code
Simplify this by having the mirroring code schedule the work item for
the update instead of requiring callers to schedule a work item
themselves.
The conversion of the callers will be done in the next patch to make
review easier.
This will later allow us to remove RTNL from different parts of the
driver. It will also allow us to only schedule the work item in case
there are active mirroring agents, which is information private to the
mirroring code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the main mirroring struct and the individual structs for the
different mirroring agents in a single allocation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct holding the different mirroring agents is currently allocated
as part of the main driver struct. This is unlike other driver modules.
Allocate the memory required to store the different mirroring agents as
part of the initialization of the mirroring module.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter pool is a shared resource. It is used by both the ACL code
to allocate counters for actions and by the routing code to allocate
counters for adjacency entries (for example).
Currently, all allocations are protected by RTNL, but this is going to
change with the removal of RTNL from the routing code.
Therefore, protect counter allocations with a spin lock.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KVDL is used to store objects allocated throughout various places
in the driver. For example, both nexthops (adjacency entries) and ACL
actions are stored in the KVDL.
Currently, all allocations are protected by RTNL, but this is going to
change with the removal of RTNL from the routing code.
Therefore, protect KVDL allocations with a lock. A mutex is used since
the free operation can block in Spectrum-2.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TNODE_KMALLOC_MAX and VERSION are not used, so remove them
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added tests for 'u32' extended match rules for u8 alignment.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: phy: Better support for BCM54810
This patch series updates the broadcom PHY driver to better support the
BCM54810 and allow it to make use of the exiting
bcm54xx_adjust_rxrefclk() as well as fix suspend/resume for it.
Changes in v2:
- added Reviewed-by tags from Andrew for patches #1 and #3
- expanded commit message in #2 to explain the change
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54810 PHY can use the standard BMCR Power down suspend, but needs
a custom resume routine which first clear the Power down bit, and then
re-initializes the PHY. While in low-power mode, the PHY only accepts
writes to the BMCR register. The datasheet clearly says it:
Reads or writes to any MII register other than MII Control register
(address 00h) while the device is in the standby power-down mode may
cause unpredictable results.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54xx_adjust_rxrefclk() already checks for PHY_BRCM_AUTO_PWRDWN_ENABLE
and PHY_BRCM_DIS_TXCRXC_NOENRGY in order to set the appropriate bit. The
situation is a bit more complicated with the flag
PHY_BRCM_RX_REFCLK_UNUSED but essentially amounts to the same situation.
The default setting for the 125MHz clock is to be on for all PHYs and
we still treat BCM50610 and BCM50610M specifically with the polarity of
the bit reversed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bcm54xx_adjust_rxrefclk() works correctly on the BCM54810
PHY, allow this device ID to proceed through.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/sfc/efx.c:116:38: warning:
efx_default_channel_type defined but not used [-Wunused-const-variable=]
commit 8397548507 ("sfc: move channel alloc/removal code")
left behind this, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8397548507 ("sfc: move channel alloc/removal code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: misc updates for -net-next
This series includes some misc updates for the HNS3
ethernet driver.
[patch 1] modifies an unsuitable print when setting dulex mode.
[patch 2] adds some debugfs info for TC and DWRR.
[patch 3] adds some debugfs info for loopback.
[patch 4] adds a missing help info for QS shaper in debugfs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver can dump QS shaper configs via debugfs, but missing
help info in debugfs for this operation.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC ID and loopback status information are obtained from
the hardware, which will be helpful for debugging. This patch
adds support for these two items in debugfs.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The actual enabled TC numbers and the DWRR weight of each
TC may be helpful for debugging, so adds them into debugfs.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if device is in link down status and user uses
'ethtool -s' command to set speed but not specify duplex
mode, the duplex mode passed from ethtool to driver is
unknown value(255), and the fibre port will identify this
value as half duplex mode and print "only copper port
supports half duplex!". This message is confusing.
So for fibre port, only the setting duplex is half, prints
error and returns.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 93c0970493 ("net: phy: consider latched link-down status in
polling mode") removed double-read of latched link-state register for
polling mode from genphy_update_link(). This added extra ~1s delay into
sequence link down->up.
Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up. In phy_state_machine is checked
link state but it is latched "link is down". The state machine is
scheduled after one second and there is detected "link is up". This
extra delay can be avoided when we keep link-state register double read
in case when link was down previously.
With this solution we don't miss a link-down event in polling mode and
link-up is faster.
Details about this quirky behavior on Realtek phy:
Without patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
here i read link-down (BMSR_LSTATUS==0),
T0+5s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
up-to-date link-up is read (BMSR_LSTATUS==1),
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
With patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
first BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==0,
second BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==1,
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: core: add helper tcp_v6_gso_csum_prep
Several network drivers for chips that support TSO6 share the same code
for preparing the TCP header, so let's factor it out to a helper.
A difference is that some drivers reset the payload_len whilst others
don't do this. This value is overwritten by TSO anyway, therefore
the new helper resets it in general.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new helper tcp_v6_gso_csum_prep in additional network drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code by using the new helper tcp_v6_gso_csum_prep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several network drivers for chips that support TSO6 share the same code
for preparing the TCP header, so let's factor it out to a helper.
A difference is that some drivers reset the payload_len whilst others
don't do this. This value is overwritten by TSO anyway, therefore
the new helper resets it in general.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is currenty possible to switch the TCP congestion control algorithm
in non-initial network namespaces:
unshare -U --map-root --net --fork --pid --mount-proc
echo "reno" > /proc/sys/net/ipv4/tcp_congestion_control
works just fine. But currently non-initial network namespaces have no
way of kowing which congestion algorithms are available or allowed other
than through trial and error by writing the names of the algorithms into
the aforementioned file.
Since we already allow changing the congestion algorithm in non-initial
network namespaces by exposing the tcp_congestion_control file there is
no reason to not also expose the
tcp_{allowed,available}_congestion_control files to non-initial network
namespaces. After this change a container with a separate network
namespace will show:
root@f1:~# ls -al /proc/sys/net/ipv4/tcp_* | grep congestion
-rw-r--r-- 1 root root 0 Feb 19 11:54 /proc/sys/net/ipv4/tcp_allowed_congestion_control
-r--r--r-- 1 root root 0 Feb 19 11:54 /proc/sys/net/ipv4/tcp_available_congestion_control
-rw-r--r-- 1 root root 0 Feb 19 11:54 /proc/sys/net/ipv4/tcp_congestion_control
Link: https://github.com/lxc/lxc/issues/3267
Reported-by: Haw Loeung <haw.loeung@canonical.com>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce "rx" prefix in the name scheme for xdp counters
on rx path.
Differentiate between XDP_TX and ndo_xdp_xmit counters
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham says:
====================
octeontx2-af: Cleanup changes
These patches cleanup AF driver by removing unnecessary function
exports and cleanup repititive logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanedup repititive nixlf and blkaddr retrieving logic
is various mailbox handlers throughout the rvu_nix.c file.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the CGX register config is restricted to mapped RVU PFs,
this patch cleans up these permission checks spread across
the rvu_cgx.c file by moving the checks to a common fn().
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
