IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
29.5V (29p5) is obviously wrong for regulator l4 and l5. Correct them
to be 2.95V (2p95). No functional change.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926072215.27517-1-shawn.guo@linaro.org
Some multiline properties (spread out over multiple lines to keep length
in check) were not indented properly, leading to misalignment with the
items above. The DT file is still small enough to address this early in
the process.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210925141841.407257-1-marijn.suijten@somainline.org
At the moment, longcheer-l8150 is using a dummy extcon-usb-gpio device
that permanently enables USB gadget mode. This workaround allows USB
to work but is actually wrong and confusing. The "vbus-gpio" used there
refers to an unused (floating) GPIO that is pulled up to make
extcon-usb-gpio report USB gadget mode permanently.
Replace this with the new &pm8916_usbin extcon device that actually
reports if an USB cable is attached or not. This allows the USB PHY
to be turned off when there is no USB cable attached and is much
cleaner overall.
Fixes: 16e8e8072108 ("arm64: dts: qcom: Add device tree for Longcheer L8150")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-3-stephan@gerhold.net
At the moment, USB gadget mode on MSM8916 works only with an extcon
device that reports the correct USB mode. This might be because the
USB PHY needs to be configured appropriately.
Unfortunately there is currently no simple approach to get such an
extcon device during early bring-up. The extcon device for USB VBUS
(i.e. gadget/peripheral mode) is typically provided by the charging
driver which is almost always very complex to port.
On pretty much all devices with PM8916, the USB VBUS is also connected
to the PM8916 "USB_IN" pad, no matter if they use the linear charger
integrated into PM8916 or not. The state of this pad can be checked
with the "USBIN_VALID" interrupt of PM8916.
The "qcom,pm8941-misc" binding exists to expose an "usb_vbus" and/or
"usb_id" interrupt from the PMIC as an extcon device.
Add a &pm8916_usbin node to pm8916.dtsi which can be used as simple
extcon device for devices that are currently lacking a proper charger
driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-2-stephan@gerhold.net
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
Add compatible values to Ethernet PHY subnodes representing Realtek
RTL8211E PHYs on RZ/G2 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/3b366e3dddd4d3cd7e89b92d3a8f78f6dc18e244.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Micrel
KSZ9031 PHYs on R-Car Gen3 boards. This allows software to identify the
PHY model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/07bd7e04dda9e84cde0664980f0b1a6d69e03109.1631174218.git.geert+renesas@glider.be
Add compatible values to Ethernet PHY subnodes representing Atheros
AR8031 PHYs on RZ/G2 boards. This allows software to identify the PHY
model at any time, regardless of the state of the PHY reset line.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/3f1b58756f149f0c634c66abaecc88e699f4c3cc.1631174218.git.geert+renesas@glider.be
While networking works fine in RGMII mode when using the Linux generic
PHY driver, it fails when using the Atheros PHY driver.
Fix this by correcting the Ethernet PHY mode to RGMII-RXID, which works
fine with both drivers.
Fixes: a5200e63af57d05e ("arm64: dts: renesas: rzg2: Convert EtherAVB to explicit delay handling")
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2a4c15b2df23bb63f15abf9dfb88860477f4f523.1632465965.git.geert+renesas@glider.be
Add miscellaneous nodes to boot the modem and support post-mortem debug
on SC7280 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-9-git-send-email-sibis@codeaurora.org
This device has a physical matrix keyboard, connected to a GPIO
expander, for which there's still no support yet.
Though, some of the keys are connected to the MSM8998 GPIOs and not
as a matrix, so these can be added.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-4-angelogioacchino.delregno@somainline.org
Add device tree support for the F(x)tec Pro 1 (QX1000) smartphone;
this is a minimal configuration to boot to serial console.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-1-angelogioacchino.delregno@somainline.org
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f55 ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason.
It turns out Longcheer L8150 actually has a BMC156 which is very similar
to BMC150, but only has an INT2 pin for the accelerometer part.
This requires some minor changes in the bmc150-accel driver which is now
supported by using the more correct bosch,bmc156_accel compatible.
Unfortunately it looks like even INT2 is not functional on most boards
because the interrupt line is not actually connected to the BMC156.
However, there are two pads next to the chip that can be shorted
to make it work if needed.
While at it, add the missing interrupts for the magnetometer part
and extra BMG160 gyroscope, those seem to work without any problems.
Also correct the magnetometer compatible to bosch,bmc156_magn for clarity
(no functional difference for the magnetometer part).
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816123544.14027-1-stephan@gerhold.net
Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.
The bootloader is VERY unpleasant, to get a bootable setup you have to run:
mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img
adb reboot bootloader
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img
fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-16-konrad.dybcio@somainline.org
Add a node for the APPS SMMU to allow for managing memory access to peripherals
such as the USB controller.
While at it, add iommus property to the USB1 node to make sure its registers can
be accessed, as they seem to be gated by default.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-15-konrad.dybcio@somainline.org
Add SDHCI1/2 nodes for eMMC and uSD card respectively.
Do note that most SM6350 devices seem to come with UFS.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Replaced SM6350_CX with its constant value]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-14-konrad.dybcio@somainline.org
Add nodes required for USB1 to function. SM6350 (thankfully) resuses SDM845 and
SC7180 IP, so no additional code porting is required.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Renamed dwc3 node "usb"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-7-konrad.dybcio@somainline.org
Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-6-konrad.dybcio@somainline.org
Add and configure GCC node to allow for referencing GCC-controlled clocks
in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-5-konrad.dybcio@somainline.org
Add RPMHCC node to allow for referencing RPMH-controlled clocks in other
nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-4-konrad.dybcio@somainline.org
Add a node for LLCC with SM6350-specific compatible.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-3-konrad.dybcio@somainline.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SM8350 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-11-git-send-email-sibis@codeaurora.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SM8250 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-10-git-send-email-sibis@codeaurora.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SM8150 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-9-git-send-email-sibis@codeaurora.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SDM845 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-8-git-send-email-sibis@codeaurora.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SC7280 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-7-git-send-email-sibis@codeaurora.org
Use the Qualcomm Mailbox Protocol (QMP) property to control the load
state resources on SC7180 SoCs and drop deprecated power-domains exposed
by AOSS QMP node.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631800770-371-6-git-send-email-sibis@codeaurora.org
Commit 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with
'motherboard-bus' nodes") broke booting on a couple of 32-bit VExpress
boards. The problem is #address-cells size changed, but interrupt-map
was not updated. This results in the timer interrupt (and all the
other motherboard interrupts) not getting mapped.
As the 'interrupt-map' properties are all just duplicates across boards,
just move them into vexpress-v2m.dtsi and vexpress-v2m-rs1.dtsi.
Strictly speaking, 'interrupt-map' is dependent on the parent
interrupt controller, but it's not likely we'll ever have a different
parent than GICv2 on these old platforms. If there was one,
'interrupt-map' can still be overridden.
Link: https://lore.kernel.org/r/20210924214221.1877686-1-robh@kernel.org
Fixes: 078fb7aa6a83 ("arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes")
Cc: Guillaume Tucker <guillaume.tucker@collabora.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Reported-by: Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The commit 82ea7d411d43 ("arm64: dts: qcom: sc7180: Base dynamic CPU
power coefficients in reality") and the commit be0416a3f917 ("arm64:
dts: qcom: Add sc7180-trogdor-homestar") passed each other in the
tubes that make up the Internet. Despite the fact the patches didn't
cause a merge conflict, they need to account for each other. Do that.
Fixes: 82ea7d411d43 ("arm64: dts: qcom: sc7180: Base dynamic CPU power coefficients in reality")
Fixes: be0416a3f917 ("arm64: dts: qcom: Add sc7180-trogdor-homestar")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923081352.1.I2a2ee0ac428a63927324d65022929565aa7d8361@changeid
All smartphones of this platform are equipped with a WCD9335 audio
codec, getting its MCLK from PM8998 gpio13: add this clock to DT.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123733.367248-7-angelogioacchino.delregno@somainline.org
All of the machines of the Sony Yoshino platform are equipped with
two cameras, sharing the same regulators configuration.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123733.367248-6-angelogioacchino.delregno@somainline.org
Add configuration for the LAB and IBB regulators (in boost mode):
this platform has smartphones with three different display sizes,
hence different displays requiring different voltage.
The common configuration parameters have been put in the common
device-tree, while specific voltage specs and soft-start-us are
variant specific, so they have been put into the machine specific
dts file.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123733.367248-5-angelogioacchino.delregno@somainline.org
