IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Compaction sysfs file is created via compaction_register_node in
register_node. But we forgot to remove it in unregister_node. Thus
compaction sysfs file is leaked. Using compaction_unregister_node
to fix this issue.
Fixes: ed4a6d7f0676 ("mm: compaction: add /sys trigger for per-node memory compaction")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Link: https://lore.kernel.org/r/20220401070905.43679-1-linmiaohe@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there are 2 matched drivers for a device using
async probe mechanism, the dev->p->async_driver might
be overridden by the last attached driver.
So just skip the later one if the previous matched driver
was not handled by async thread yet.
Below is my use case which having this problem.
Make both driver mmcblk and mmc_test allow async probe,
the dev->p->async_driver will be overridden by the later driver
mmc_test and bind to the device then claim it for testing.
When it happen, mmcblk will never do probe again.
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Link: https://lore.kernel.org/r/20220316074328.1801-1-mark-pk.tsai@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add error injection capability to the test_firmware module specifically
for firmware upload testing. Error injection instructions are transferred
as the first part of the firmware payload. The format of an error
injection string is similar to the error strings that may be read from
the error sysfs node.
To inject the error "programming:hw-error", one would use the error
injection string "inject:programming:hw-error" as the firmware payload:
$ echo 1 > loading
$ echo inject:programming:hw-error > data
$ echo 0 > loading
$ cat status
idle
$ cat error
programming:hw-error
The first part of the error string is the progress state of the upload at
the time of the error. The progress state would be one of the following:
"preparing", "transferring", or "programming". The second part of the
error string is one of the following: "hw-error", "timeout", "device-busy",
"invalid-file-size", "read-write-error", "flash-wearout", and "user-abort".
Note that all of the error strings except "user-abort" will fail without
delay. The "user-abort" error will cause the firmware upload to stall at
the requested progress state for up to 5 minutes to allow you to echo 1
to the cancel sysfs node. It is this cancellation that causes the
'user-abort" error. If the upload is not cancelled within the 5 minute
time period, then the upload will complete without an error.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-8-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for testing the firmware upload driver. There are four sysfs
nodes added:
upload_register: write-only
Write the name of the firmware device node to be created
upload_unregister: write-only
Write the name of the firmware device node to be destroyed
config_upload_name: read/write
Set the name to be used by upload_read
upload_read: read-only
Read back the data associated with the firmware device node named
in config_upload_name
You can create multiple, concurrent firmware device nodes for firmware
upload testing. Read firmware back and validate it using config_upload_name
and upload_red.
Example:
$ cd /sys/devices/virtual/misc/test_firmware
$ echo -n fw1 > upload_register
$ ls fw1
cancel data device error loading power remaining_size status
subsystem uevent
$ dd if=/dev/urandom of=/tmp/random-firmware.bin bs=512 count=4
4+0 records in
4+0 records out
2048 bytes (2.0 kB, 2.0 KiB) copied, 0.000131959 s, 15.5 MB/s
$ echo 1 > fw1/loading
$ cat /tmp/random-firmware.bin > fw1/data
$ echo 0 > fw1/loading
$ cat fw1/status
idle
$ cat fw1/error
$ echo -n fw1 > config_upload_name
$ cmp /tmp/random-firmware.bin upload_read
$ echo $?
0
$ echo -n fw1 > upload_unregister
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-7-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add additional sysfs nodes to monitor the transfer of firmware upload data
to the target device:
cancel: Write 1 to cancel the data transfer
error: Display error status for a failed firmware upload
remaining_size: Display the remaining amount of data to be transferred
status: Display the progress of the firmware upload
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-6-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the firmware subsystem to support a persistent sysfs interface that
userspace may use to initiate a firmware update. For example, FPGA based
PCIe cards load firmware and FPGA images from local FLASH when the card
boots. The images in FLASH may be updated with new images provided by the
user at his/her convenience.
A device driver may call firmware_upload_register() to expose persistent
"loading" and "data" sysfs files. These files are used in the same way as
the fallback sysfs "loading" and "data" files. When 0 is written to
"loading" to complete the write of firmware data, the data is transferred
to the lower-level driver using pre-registered call-back functions. The
data transfer is done in the context of a kernel worker thread.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-5-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for sharing the "loading" and "data" sysfs nodes with the
new firmware upload support, split out sysfs functionality from fallback.c
and fallback.h into sysfs.c and sysfs.h. This includes the firmware
class driver code that is associated with the sysfs files and the
fw_fallback_config support for the timeout sysfs node.
CONFIG_FW_LOADER_SYSFS is created and is selected by
CONFIG_FW_LOADER_USER_HELPER in order to include sysfs.o in
firmware_class-objs.
This is mostly just a code reorganization. There are a few symbols that
change in scope, and these can be identified by looking at the header
file changes. A few white-space warnings from checkpatch are also
addressed in this patch.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-4-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The help message of 'get_abi.pl' is mistakenly saying it's
'abi_book.pl'. This commit fixes the wrong name in the help message.
Fixes: bbc249f2b859 ("scripts: add an script to parse the ABI files")
Signed-off-by: SeongJae Park <sj@kernel.org>
Link: https://lore.kernel.org/r/20220419121636.290407-1-sj@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__add_memory_block() calls both put_device() and device_unregister() when
storing the memory block into the xarray. This is incorrect because xarray
doesn't take an additional reference and device_unregister() already calls
put_device().
Triggering the issue looks really unlikely and its only effect should be to
log a spurious warning about a ref counted issue.
Fixes: 4fb6eabf1037 ("drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Link: https://lore.kernel.org/r/d44c63d78affe844f020dc02ad6af29abc448fc4.1650611702.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Because previous configurations were relying on the userspace fallback
mechanism, the security context of the userspace daemon (i.e. ueventd)
was consistently used to read firmware files. More devices are found to
use the command line argument firmware_class.path which gives the kernel
the opportunity to read the firmware directly, hence surfacing this
misattribution.
Signed-off-by: Thiébaud Weksteen <tweek@google.com>
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Tested-by: John Stultz <jstultz@google.com>
Link: https://lore.kernel.org/r/20220422013215.2301793-1-tweek@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rename fw_sysfs_done() and fw_sysfs_loading() to fw_state_is_done() and
fw_state_is_loading() respectively, and place them along side companion
functions in drivers/base/firmware_loader/firmware.h.
Use the fw_state_is_done() function to exit early from
firmware_loading_store() if the state is already "done". This is being done
in preparation for supporting persistent sysfs nodes to allow userspace to
upload firmware to a device, potentially reusing the sysfs loading and data
files multiple times.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-3-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fw_free_paged_buf() function resets the paged buffer information in
the fw_priv data structure. Additionally, clear the data and size members
of fw_priv in order to facilitate the reuse of fw_priv. This is being
done in preparation for enabling userspace to initiate multiple firmware
uploads using this sysfs interface.
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tianfei zhang <tianfei.zhang@intel.com>
Tested-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20220421212204.36052-2-russell.h.weight@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override field from platform driver should not be initialized
from static memory (string literal) because the core later kfree() it,
for example when driver_override is set via sysfs.
Use dedicated helper to set driver_override properly.
Fixes: 950a7388f02b ("rpmsg: Turn name service into a stand alone driver")
Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-13-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory pointed by variable 'old' in field store macro is not modified,
so it can be made a pointer to const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-12-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override field from platform driver should not be initialized
from static memory (string literal) because the core later kfree() it,
for example when driver_override is set via sysfs.
Use dedicated helper to set driver_override properly.
Fixes: 917809e2280b ("slimbus: ngd: Add qcom SLIMBus NGD driver")
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-11-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override field from platform driver should not be initialized
from static memory (string literal) because the core later kfree() it,
for example when driver_override is set via sysfs.
Use dedicated helper to set driver_override properly.
Fixes: 77d8f3068c63 ("clk: imx: scu: add two cells binding support")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-10-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to the reduce amount of duplicated
code.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-9-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to the reduce amount of duplicated
code.
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to the reduce amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Acked-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to the reduce amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to the reduce amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-5-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to reduce the amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a helper to set driver_override to reduce the amount of duplicated
code. Make the driver_override field const char, because it is not
modified by the core and it matches other subsystems.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several core drivers and buses expect that driver_override is a
dynamically allocated memory thus later they can kfree() it.
However such assumption is not documented, there were in the past and
there are already users setting it to a string literal. This leads to
kfree() of static memory during device release (e.g. in error paths or
during unbind):
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058da50>] (platform_device_release+0x88/0xb4)
(platform_device_release) from [<c0585be0>] (device_release+0x2c/0x90)
(device_release) from [<c0a69050>] (kobject_put+0xec/0x20c)
(kobject_put) from [<c0f2f120>] (exynos5_clk_probe+0x154/0x18c)
(exynos5_clk_probe) from [<c058de70>] (platform_drv_probe+0x6c/0xa4)
(platform_drv_probe) from [<c058b7ac>] (really_probe+0x280/0x414)
(really_probe) from [<c058baf4>] (driver_probe_device+0x78/0x1c4)
(driver_probe_device) from [<c0589854>] (bus_for_each_drv+0x74/0xb8)
(bus_for_each_drv) from [<c058b48c>] (__device_attach+0xd4/0x16c)
(__device_attach) from [<c058a638>] (bus_probe_device+0x88/0x90)
(bus_probe_device) from [<c05871fc>] (device_add+0x3dc/0x62c)
(device_add) from [<c075ff10>] (of_platform_device_create_pdata+0x94/0xbc)
(of_platform_device_create_pdata) from [<c07600ec>] (of_platform_bus_create+0x1a8/0x4fc)
(of_platform_bus_create) from [<c0760150>] (of_platform_bus_create+0x20c/0x4fc)
(of_platform_bus_create) from [<c07605f0>] (of_platform_populate+0x84/0x118)
(of_platform_populate) from [<c0f3c964>] (of_platform_default_populate_init+0xa0/0xb8)
(of_platform_default_populate_init) from [<c01031f8>] (do_one_initcall+0x8c/0x404)
Provide a helper which clearly documents the usage of driver_override.
This will allow later to reuse the helper and reduce the amount of
duplicated code.
Convert the platform driver to use a new helper and make the
driver_override field const char (it is not modified by the core).
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220419113435.246203-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xz -9 option leads to an unnecessarily too large dictionary that
isn't really suitable for the kernel firmware loader. Pass the
dictionary size explicitly, instead.
While we're at it, make the xz command call defined in $RUN_XZ for
simplicity.
Fixes: 108ae07c5036 ("selftests: firmware: Add compressed firmware tests")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220421152908.4718-3-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the growing demand on ZSTD compressions, there have been requests
for the support of ZSTD-compressed firmware files, so here it is:
this patch extends the firmware loader code to allow loading ZSTD
files. The implementation is fairly straightforward, it just adds a
ZSTD decompression routine for the file expander. (And the code is
even simpler than XZ thanks to the ZSTD API that gives the original
decompressed size from the header.)
Link: https://lore.kernel.org/all/20210127154939.13288-1-tiwai@suse.de/
Tested-by: Piotr Gorski <lucjan.lucjanov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220421152908.4718-2-tiwai@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a single serial driver fix for a build issue that showed up due
to changes that came in through the tty tree in 5.18-rc1 that were
missed previously. It resolves a build error with the mpc52xx_uart
driver.
It has been in linux-next this week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYlLSOw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykUDQCgpgjEqSAUVXHS3NMjIppMSF8RfD4AoNYjH7Hl
oVs5nzWNDcbZPvvh+TFw
=F6pL
-----END PGP SIGNATURE-----
Merge tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"This is a single serial driver fix for a build issue that showed up
due to changes that came in through the tty tree in 5.18-rc1 that were
missed previously. It resolves a build error with the mpc52xx_uart
driver.
It has been in linux-next this week with no reported problems"
* tag 'tty-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: mpc52xx_uart: make rx/tx hooks return unsigned, part II.
Here is a single staging driver fix for 5.18-rc2 that resolves an endian
issue for the r8188eu driver. It has been in linux-next all this week
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYlLRlw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqdgCcCNVlN2uYRqAYjVyZmYSNKumgzN8AoMm1/DVT
bT68T73BB/g1TFMNjuwy
=Ho+t
-----END PGP SIGNATURE-----
Merge tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.18-rc2 that resolves an
endian issue for the r8188eu driver. It has been in linux-next all
this week with no reported problems"
* tag 'staging-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Fix PPPoE tag insertion on little endian systems
Here are 2 small driver core changes for 5.18-rc2.
They are the final bits in the removal of the default_attrs field in
struct kobj_type. I had to wait until after 5.18-rc1 for all of the
changes to do this came in through different development trees, and then
one new user snuck in. So this series has 2 changes:
- removal of the default_attrs field in the powerpc/pseries/vas
code. Change has been acked by the PPC maintainers to come
through this tree
- removal of default_attrs from struct kobj_type now that all
in-kernel users are removed. This cleans up the kobject code
a little bit and removes some duplicated functionality that
confused people (now there is only one way to do default
groups.)
All of these have been in linux-next for all of this week with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYlLRHg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn+9gCfXN0OvKmw5QD55z8YGp/jIycK0ToAnifJ/OX+
sU2V8ZQfNbV8xw7iXfc2
=L+Uc
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are two small driver core changes for 5.18-rc2.
They are the final bits in the removal of the default_attrs field in
struct kobj_type. I had to wait until after 5.18-rc1 for all of the
changes to do this came in through different development trees, and
then one new user snuck in. So this series has two changes:
- removal of the default_attrs field in the powerpc/pseries/vas code.
The change has been acked by the PPC maintainers to come through
this tree
- removal of default_attrs from struct kobj_type now that all
in-kernel users are removed.
This cleans up the kobject code a little bit and removes some
duplicated functionality that confused people (now there is only
one way to do default groups)
Both of these have been in linux-next for all of this week with no
reported problems"
* tag 'driver-core-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kobject: kobj_type: remove default_attrs
powerpc/pseries/vas: use default_groups in kobj_type
Here is a single driver fix for 5.18-rc2. It resolves the build warning
issue on 32bit systems in the habannalabs driver that came in during the
5.18-rc1 merge cycle.
It has been in linux-next for all this week with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYlK+5Q8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykTKQCgoOU9/+9EiS3crSlFzo24SdomjKAAoL1nQoN9
2s4KLX25ynnincGifSr5
=VVFs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"A single driver fix. It resolves the build warning issue on 32bit
systems in the habannalabs driver that came in during the 5.18-rc1
merge cycle.
It has been in linux-next for all this week with no reported problems"
* tag 'char-misc-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
habanalabs: Fix test build failures
- Fix KVM "lost kick" race, where an attempt to pull a vcpu out of the guest could be
lost (or delayed until the next guest exit).
- Disable SCV (system call vectored) when PR KVM guests could be run.
- Fix KVM PR guests using SCV, by disallowing AIL != 0 for KVM PR guests.
- Add a new KVM CAP to indicate if AIL == 3 is supported.
- Fix a regression when hotplugging a CPU to a memoryless/cpuless node.
- Make virt_addr_valid() stricter for 64-bit Book3E & 32-bit, which fixes crashes seen
due to hardened usercopy.
- Revert a change to max_mapnr which broke HIGHMEM.
Thanks to: Christophe Leroy, Fabiano Rosas, Kefeng Wang, Nicholas Piggin, Srikar Dronamraju.
-----BEGIN PGP SIGNATURE-----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=uNqF
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix KVM "lost kick" race, where an attempt to pull a vcpu out of the
guest could be lost (or delayed until the next guest exit).
- Disable SCV (system call vectored) when PR KVM guests could be run.
- Fix KVM PR guests using SCV, by disallowing AIL != 0 for KVM PR
guests.
- Add a new KVM CAP to indicate if AIL == 3 is supported.
- Fix a regression when hotplugging a CPU to a memoryless/cpuless node.
- Make virt_addr_valid() stricter for 64-bit Book3E & 32-bit, which
fixes crashes seen due to hardened usercopy.
- Revert a change to max_mapnr which broke HIGHMEM.
Thanks to Christophe Leroy, Fabiano Rosas, Kefeng Wang, Nicholas Piggin,
and Srikar Dronamraju.
* tag 'powerpc-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
Revert "powerpc: Set max_mapnr correctly"
powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit
KVM: PPC: Move kvmhv_on_pseries() into kvm_ppc.h
powerpc/numa: Handle partially initialized numa nodes
powerpc/64: Fix build failure with allyesconfig in book3s_64_entry.S
KVM: PPC: Use KVM_CAP_PPC_AIL_MODE_3
KVM: PPC: Book3S PR: Disallow AIL != 0
KVM: PPC: Book3S PR: Disable SCV when AIL could be disabled
KVM: PPC: Book3S HV P9: Fix "lost kick" race
- A fix for a long standing bug in the ARM GICv3 redistributor polling
which uses the wrong bit number to test.
- Prevent translation of bogus ACPI table entries which map device
interrupts into the IPI space on ARM GICs.
- Don't write into the pending register of ARM GICV4 before the scan
in hardware has completed.
- A set of build and correctness fixes for the Qualcomm MPM driver
-----BEGIN PGP SIGNATURE-----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=SJ8P
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of interrupt chip driver fixes:
- A fix for a long standing bug in the ARM GICv3 redistributor
polling which uses the wrong bit number to test.
- Prevent translation of bogus ACPI table entries which map device
interrupts into the IPI space on ARM GICs.
- Don't write into the pending register of ARM GICV4 before the scan
in hardware has completed.
- A set of build and correctness fixes for the Qualcomm MPM driver"
* tag 'irq-urgent-2022-04-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic, gic-v3: Prevent GSI to SGI translations
irqchip/gic-v3: Fix GICR_CTLR.RWP polling
irqchip/gic-v4: Wait for GICR_VPENDBASER.Dirty to clear before descheduling
irqchip/irq-qcom-mpm: fix return value check in qcom_mpm_init()
irq/qcom-mpm: Fix build error without MAILBOX
- Use local labels in the exception table macros to avoid symbol
conflicts with clang LTO builds
- A couple of fixes to objtool checking of the relatively newly added
SLS and IBT code
- Rename a local var in the WARN* macro machinery to prevent shadowing
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAmJSwSkACgkQEsHwGGHe
VUp6QQ//TGhL2xxLoN+7pYjIBDEDHJ3Oi0m6fOweqyQAZTYcm/rAPqd7hvoWVSoO
YsLdWi9jeMwkzG0ItSm/qPVm/UvrViXwuQMdz4nDWqg2IPFIbhgNA3CKCIyPTio2
WHp2NXvYyDnwPMr6xTTRndMDoxiwxMBnXf91pNwoU3toxw0GuUuXan0Y+GKnvx1A
sqhbpWO27bAmhKb26wPw5soJVxBbSqx+1TbFVG0Sz/uwYQowMa+nfNg1DXF0sXyJ
E/ssqBB6wjl7ANVbQsxBQHRzr/EksLVPwHHrlT8ga/5loin+VJ6mTBCPLgG7SMBE
+R1fm79Bp/9KU194fcqhJ3pvnyJPi8hfizzCqNKnK871V8LRzC+jW0l3EdvASEXC
sDj0XWsSFoWft9eAtMV11d641uVC4rLB90GyyzmWWrEw9BbxmasBgED6QBx9d+V6
o1L4y58Tsz88HKzwd0PtBkeGDkvkA7xOx8ViG24IeLA0tcbixnfnATQdelQeWKqO
4m3o1JU8ogJp9JCEBY7ZeXyStFjZMedM4U/V0akF6AKnpDuVfR3T5C68cYhoLKBu
XU6Swf5sFHImNWp0+54HPnXhHj/uhuwj9YWCkxx/eXViwvVlxSdTdIQWa380EddN
0KhOFLwLOdhha2+81FJc6vmkDHwiu6hlR38yqdGvdxZf/KPKjM0=
=kMtP
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix the MSI message data struct definition
- Use local labels in the exception table macros to avoid symbol
conflicts with clang LTO builds
- A couple of fixes to objtool checking of the relatively newly added
SLS and IBT code
- Rename a local var in the WARN* macro machinery to prevent shadowing
* tag 'x86_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/msi: Fix msi message data shadow struct
x86/extable: Prefer local labels in .set directives
x86,bpf: Avoid IBT objtool warning
objtool: Fix SLS validation for kcov tail-call replacement
objtool: Fix IBT tail-call detection
x86/bug: Prevent shadowing in __WARN_FLAGS
x86/mm/tlb: Revert retpoline avoidance approach
- A couple of fixes to event encoding on Sapphire Rapids
- Pass event caps of inherited events so that perf doesn't fail wrongly at fork()
- Add support for a new Raptor Lake CPU
-----BEGIN PGP SIGNATURE-----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=ba3V
-----END PGP SIGNATURE-----
Merge tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- A couple of fixes to cgroup-related handling of perf events
- A couple of fixes to event encoding on Sapphire Rapids
- Pass event caps of inherited events so that perf doesn't fail wrongly
at fork()
- Add support for a new Raptor Lake CPU
* tag 'perf_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Always set cpuctx cgrp when enable cgroup event
perf/core: Fix perf_cgroup_switch()
perf/core: Use perf_cgroup_info->active to check if cgroup is active
perf/core: Don't pass task around when ctx sched in
perf/x86/intel: Update the FRONTEND MSR mask on Sapphire Rapids
perf/x86/intel: Don't extend the pseudo-encoding to GP counters
perf/core: Inherit event_caps
perf/x86/uncore: Add Raptor Lake uncore support
perf/x86/msr: Add Raptor Lake CPU support
perf/x86/cstate: Add Raptor Lake support
perf/x86: Add Intel Raptor Lake support
the local_lock_* macros back to inline functions
- A couple of fixes to static call insn patching
-----BEGIN PGP SIGNATURE-----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=hSOc
-----END PGP SIGNATURE-----
Merge tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
- Allow the compiler to optimize away unused percpu accesses and change
the local_lock_* macros back to inline functions
- A couple of fixes to static call insn patching
* tag 'locking_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "mm/page_alloc: mark pagesets as __maybe_unused"
Revert "locking/local_lock: Make the empty local_lock_*() function a macro."
x86/percpu: Remove volatile from arch_raw_cpu_ptr().
static_call: Remove __DEFINE_STATIC_CALL macro
static_call: Properly initialise DEFINE_STATIC_CALL_RET0()
static_call: Don't make __static_call_return0 static
x86,static_call: Fix __static_call_return0 for i386
- Two fixes for the new forceidle balancer
-----BEGIN PGP SIGNATURE-----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=elMK
-----END PGP SIGNATURE-----
Merge tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Use the correct static key checking primitive on the IRQ exit path
- Two fixes for the new forceidle balancer
* tag 'sched_urgent_for_v5.18_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
entry: Fix compile error in dynamic_irqentry_exit_cond_resched()
sched: Teach the forced-newidle balancer about CPU affinity limitation.
sched/core: Fix forceidle balancing
- Fix the clang command line option probing and remove some options to filter
out, fixing the build with the latest clang versions.
- Fix 'perf bench' futex and epoll benchmarks to deal with machines with more
than 1K CPUs.
- Fix 'perf test tsc' error message when not supported.
- Remap perf ring buffer if there is no space for event, fixing perf usage
in 32-bit ChromeOS.
- Drop objdump stderr to avoid getting stuck waiting for stdout output in
'perf annotate'.
- Fix up garbled output by now showing unwind error messages when augmenting
frame in best effort mode.
- Fix perf's libperf_print callback, use the va_args eprintf() variant.
- Sync vhost and arm64 cputype headers with the kernel sources.
- Fix 'perf report --mem-mode' with ARM SPE.
- Add missing external commands ('perf iiostat', etc) to 'perf --list-cmds'.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYlIM+gAKCRCyPKLppCJ+
J5l6AQCCY4co/6FBh8JMmMX4RVHAUriX0YfKTJfpeLU3nsiXPAD/TVqf1LOyYaPv
/ZqJ8DwqvKr9nkUsf5kAOfPrDB/j/QQ=
=0UV/
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix the clang command line option probing and remove some options to
filter out, fixing the build with the latest clang versions
- Fix 'perf bench' futex and epoll benchmarks to deal with machines
with more than 1K CPUs
- Fix 'perf test tsc' error message when not supported
- Remap perf ring buffer if there is no space for event, fixing perf
usage in 32-bit ChromeOS
- Drop objdump stderr to avoid getting stuck waiting for stdout output
in 'perf annotate'
- Fix up garbled output by now showing unwind error messages when
augmenting frame in best effort mode
- Fix perf's libperf_print callback, use the va_args eprintf() variant
- Sync vhost and arm64 cputype headers with the kernel sources
- Fix 'perf report --mem-mode' with ARM SPE
- Add missing external commands ('iiostat', etc) to 'perf --list-cmds'
* tag 'perf-tools-fixes-for-v5.18-2022-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf annotate: Drop objdump stderr to avoid getting stuck waiting for stdout output
perf tools: Add external commands to list-cmds
perf docs: Add perf-iostat link to manpages
perf session: Remap buf if there is no space for event
perf bench: Fix epoll bench to correct usage of affinity for machines with #CPUs > 1K
perf bench: Fix futex bench to correct usage of affinity for machines with #CPUs > 1K
perf tools: Fix perf's libperf_print callback
perf: arm-spe: Fix perf report --mem-mode
perf unwind: Don't show unwind error messages when augmenting frame pointer stack
tools headers arm64: Sync arm64's cputype.h with the kernel sources
perf test tsc: Fix error message when not supported
perf build: Don't use -ffat-lto-objects in the python feature test when building with clang-13
perf python: Fix probing for some clang command line options
tools build: Filter out options and warnings not supported by clang
tools build: Use $(shell ) instead of `` to get embedded libperl's ccopts
tools include UAPI: Sync linux/vhost.h with the kernel sources
- Fix a compile error in the nvdimm unit tests
- Fix a shadowed variable warning in the CXL PCI driver
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSbo+XnGs+rwLz9XGXfioYZHlFsZwUCYlIY6QAKCRDfioYZHlFs
Z0aeAQDDYcicYRhLZ3Ljbg6stitBIumpdVcKDHm4WkC9gbmB4QEArnXLpcHPWyAa
zmgc1Yrp9gOnpNSRMog9Wc8NaR45KA8=
=Ov5t
-----END PGP SIGNATURE-----
Merge tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull cxl and nvdimm fixes from Dan Williams:
- Fix a compile error in the nvdimm unit tests
- Fix a shadowed variable warning in the CXL PCI driver
* tag 'cxl+nvdimm-for-5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
cxl/pci: Drop shadowed variable
tools/testing/nvdimm: Fix security_init() symbol collision
- fix a race condition with consumers accessing the fields of GPIO IRQ chips
before they're fully initialized
-----BEGIN PGP SIGNATURE-----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=faCF
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a race condition with consumers accessing the fields of GPIO IRQ
chips before they're fully initialized
* tag 'gpio-fixes-for-v5.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: Restrict usage of GPIO chip irq members before initialization
- Fix GICv3 polling for RWP in redistributors
- Reject ACPI attempts to use SGIs on GIC/GICv3
- Fix unpredictible behaviour when making a VPE non-resident
with GICv4
- A couple of fixes for the newly merged qcom-mpm driver
-----BEGIN PGP SIGNATURE-----
iQJDBAABCgAtFiEEn9UcU+C1Yxj9lZw9I9DQutE9ekMFAmJRUIQPHG1hekBrZXJu
ZWwub3JnAAoJECPQ0LrRPXpDJsYP/A1wjOMvcK2HHRDdKXgc65sFrv0uI4kZw1yX
UxxRp/nwYo7uuz3L/k7D4/C96nMERP2rjiF2Y4NURLEhgVlh3iNK/lQWb9eVsN04
jX33c3qOeH5kNAy89uYv1PnNy/QjjIm3LFh0lSXCLEDK0CV3l+LKcuGDHVn8pP0B
2rd/N+s0Hc/SL2W/cV+pGkoJK9RGfWojC6SalFjFD/n8jE2jBNcMGeeZERdNhuVP
r/ZwMEtM248KFyCX04QKidDexk37HZmrgq1K+RlPX60zqu/hcsDO27zF/qhru+U+
Kr8WPLHsrzCo//9b5o8s/WTZE9QXA7QmTGum2KHfQazDug7YSk5Fgh1t7f1dSVAw
Yh7cNtWXqa63I4woBlUtR8AImnIbM/a66Qeim+RZRl8QI5IMndgcLQaNu/IeoqVs
wUNVX32mnQ0ee3Von/ADSBL+4ibqxQiw11ZXZU8/1Dc+teaMBshVdcHrug+iU7e8
ftjwyf9IUsiITTNrExm6CDkzL27hbwHoHAD3eDkNisqTyJYmyWvL36kab88NgCAg
Moc9WH2XkM4fZv0/9OADdyPJUOLtuZw85/45O2ydGVvpvW3GVmo06xt6P70P3/rq
x2aU6n7CpYRrFZn7IL1hY8HBUXS+s/Ya65B7/L63yngyq8xAslkYOwcTx/XjHpEP
EQt3/t9f
=W3KX
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Fix GICv3 polling for RWP in redistributors
- Reject ACPI attempts to use SGIs on GIC/GICv3
- Fix unpredictible behaviour when making a VPE non-resident
with GICv4
- A couple of fixes for the newly merged qcom-mpm driver
Link: https://lore.kernel.org/lkml/20220409094229.267649-1-maz@kernel.org
If objdump writes to stderr it can block waiting for it to be read. As
perf doesn't read stderr then progress stops with perf waiting for
stdout output.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexandre Truong <alexandre.truong@arm.com>
Cc: Dave Marchevsky <davemarchevsky@fb.com>
Cc: Denis Nikitin <denik@chromium.org>
Cc: German Gomez <german.gomez@arm.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Lexi Shao <shaolexi@huawei.com>
Cc: Li Huafei <lihuafei1@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Liška <mliska@suse.cz>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@amd.com>
Cc: Remi Bernon <rbernon@codeweavers.com>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Song Liu <songliubraving@fb.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Will Deacon <will@kernel.org>
Cc: William Cohen <wcohen@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20220407230503.1265036-2-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The `perf --list-cmds` output prints only internal commands, although
there is no reason for that from users' perspective.
Adding the external commands to commands array with NULL function
pointer allows printing all perf commands while not changing the logic
of command handler selection.
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/r/20220404221541.30312-2-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
If a perf event doesn't fit into remaining buffer space return NULL to
remap buf and fetch the event again.
Keep the logic to error out on inadequate input from fuzzing.
This fixes perf failing on ChromeOS (with 32b userspace):
$ perf report -v -i perf.data
...
prefetch_event: head=0x1fffff8 event->header_size=0x30, mmap_size=0x2000000: fuzzed or compressed perf.data?
Error:
failed to process sample
Fixes: 57fc032ad643ffd0 ("perf session: Avoid infinite loop when seeing invalid header.size")
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Denis Nikitin <denik@chromium.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/r/20220330031130.2152327-1-denik@chromium.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
38 Patches, two adding support for new devices (ufs, mvsas), a major
set of six fixes in lpfc plus a huge chunk removal in pmcraid to get
rid of a driver specific ioctl and a major rework of aha152x to get
rid of the scsi_pointer. The rest are minor fixes and obvious changes
including several spelling updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCYlGRXSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSAgAP42HLBW
4cL+Mff4MRKYgS3AVWjJevI3m2mnXB6NQ6Xe/QD/beI0Ppx5s7q6VQvDvU/wvVYI
tfne0SAy8Bi6V82cjlI=
=LJ3r
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
- add support for new devices (ufs, mvsas)
- a major set of fixes in lpfc
- get rid of a driver specific ioctl in pcmraid
- a major rework of aha152x to get rid of the scsi_pointer.
- minor fixes and obvious changes including several spelling updates.
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (36 commits)
scsi: megaraid_sas: Target with invalid LUN ID is deleted during scan
scsi: ufs: ufshpb: Fix a NULL check on list iterator
scsi: sd: Clean up gendisk if device_add_disk() failed
scsi: message: fusion: Remove redundant variable dmp
scsi: mvsas: Add PCI ID of RocketRaid 2640
scsi: sd: sd_read_cpr() requires VPD pages
scsi: mpt3sas: Fail reset operation if config request timed out
scsi: sym53c500_cs: Stop using struct scsi_pointer
scsi: ufs: ufs-pci: Add support for Intel MTL
scsi: mpt3sas: Fix mpt3sas_check_same_4gb_region() kdoc comment
scsi: scsi_debug: Fix sdebug_blk_mq_poll() in_use_bm bitmap use
scsi: bnx2i: Fix spelling mistake "mis-match" -> "mismatch"
scsi: bnx2fc: Fix spelling mistake "mis-match" -> "mismatch"
scsi: zorro7xx: Fix a resource leak in zorro7xx_remove_one()
scsi: aic7xxx: Use standard PCI subsystem, subdevice defines
scsi: ufs: qcom: Drop custom Android boot parameters
scsi: core: sysfs: Remove comments that conflict with the actual logic
scsi: hisi_sas: Remove stray fallthrough annotation
scsi: virtio-scsi: Eliminate anonymous module_init & module_exit
scsi: isci: Fix spelling mistake "doesnt" -> "doesn't"
...
