IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
From: Stephen Warren:
ARM: tegra: core SoC enhancements for 3.12
This branch includes a number of enhancements to core SoC support for
Tegra devices. The major new features are:
* Adds a new CPU-power-gated cpuidle state for Tegra114.
* Adds initial system suspend support for Tegra114, initially supporting
just CPU-power-gating during suspend.
* Adds "LP1" suspend mode support for all of Tegra20/30/114. This mode
both gates CPU power, and places the DRAM into self-refresh mode.
* A new DT-driven PCIe driver to Tegra20/30. The driver is also moved
from arch/arm/mach-tegra/ to drivers/pci/host/.
The PCIe driver work depends on the following tag from Thomas Petazzoni:
git://git.infradead.org/linux-mvebu.git mis-3.12.2
... which is merged into the middle of this pull request.
* tag 'tegra-for-3.12-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (33 commits)
ARM: tegra: disable LP2 cpuidle state if PCIe is enabled
MAINTAINERS: Add myself as Tegra PCIe maintainer
PCI: tegra: set up PADS_REFCLK_CFG1
PCI: tegra: Add Tegra 30 PCIe support
PCI: tegra: Move PCIe driver to drivers/pci/host
PCI: msi: add default MSI operations for !HAVE_GENERIC_HARDIRQS platforms
ARM: tegra: add LP1 suspend support for Tegra114
ARM: tegra: add LP1 suspend support for Tegra20
ARM: tegra: add LP1 suspend support for Tegra30
ARM: tegra: add common LP1 suspend support
clk: tegra114: add LP1 suspend/resume support
ARM: tegra: config the polarity of the request of sys clock
ARM: tegra: add common resume handling code for LP1 resuming
ARM: pci: add ->add_bus() and ->remove_bus() hooks to hw_pci
of: pci: add registry of MSI chips
PCI: Introduce new MSI chip infrastructure
PCI: remove ARCH_SUPPORTS_MSI kconfig option
PCI: use weak functions for MSI arch-specific functions
ARM: tegra: unify Tegra's Kconfig a bit more
ARM: tegra: remove the limitation that Tegra114 can't support suspend
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Tony Lindgren:
Minimal DRA7xx based SoC core support via Rajendra Nayak <rnayak@ti.com>
* tag 'omap-for-v3.12/dra7xx' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (849 commits)
ARM: DRA7: Add the build support in omap2plus
ARM: DRA7: hwmod: Reuse the soc_ops used for OMAP4/5
ARM: DRA7: id: Add cpu detection support for DRA7xx based SoCs'
ARM: DRA7: Kconfig: Make ARCH_NR_GPIO default to 512
ARM: DRA7: board-generic: Add basic DT support
ARM: DRA7: Resue the clocksource, clockevent support
ARM: DRA7: Reuse io tables and add a new .init_early
ARM: DRA7: Reuse all of PRCM and MPUSS SMP infra
Linux 3.11-rc5
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
dlm: kill the unnecessary and wrong device_close()->recalc_sigpending()
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
From Jason Cooper:
mvebu drivers changes for v3.12
- MBus devicetree bindings
- devbus update for address decoding window, cleanup
* tag 'drivers-3.12' of git://git.infradead.org/linux-mvebu: (35 commits)
memory: mvebu-devbus: Remove unused variable
ARM: mvebu: Relocate PCIe node in Armada 370 RD board
ARM: mvebu: Fix AXP-WiFi-AP DT for MBUS DT binding
ARM: mvebu: add support for the AXP WiFi AP board
ARM: mvebu: use dts pre-processor for mv78230
PCI: mvebu: Adapt to the new device tree layout
bus: mvebu-mbus: Add devicetree binding
ARM: kirkwood: Relocate PCIe device tree nodes
ARM: kirkwood: Introduce MBUS_ID
ARM: kirkwood: Introduce MBus DT node
ARM: kirkwood: Use the preprocessor on device tree files
ARM: kirkwood: Split DT and legacy MBus initialization
ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
ARM: mvebu: Relocate Armada 370/XP DeviceBus device tree nodes
ARM: mvebu: Add BootROM to Armada 370/XP device tree
ARM: mvebu: Add MBus to Armada 370/XP device tree
ARM: mvebu: Use the preprocessor on Armada 370/XP device tree files
ARM: mvebu: Initialize MBus using the DT binding
ARM: mvebu: Remove the harcoded BootROM window allocation
bus: mvebu-mbus: Factorize Armada 370/XP data structures
...
Signed-off-by: Olof Johansson <olof@lixom.net>
If CONFIG_FRAME_POINTER=y we get the following error:
arch/arm/mach-vexpress/tc2_pm.c: In function 'tc2_pm_down':
arch/arm/mach-vexpress/tc2_pm.c:200:1: error: fp cannot be used in asm here
Let's fix that by explicitly preserving r11 on the stack and removing it
from the clobber list.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.12
* Increased clock coverage for r8a7740 and r8a7790 SoCs
* tag 'renesas-soc2-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7740: Add TPU clock entry for DT platforms
ARM: shmobile: r8a7790: clocks for Ether support
ARM: shmobile: r8a7740: Fix TPU clock name
ARM: shmobile: Insert align directives before 4 bytes data
ARM: shmobile: Force ARM mode to compile reset vector for secondary CPUs
ARM: shmobile: fix compile error when CONFIG_THUMB2_KERNEL=y
ARM: shmobile: Update romImage to relocate appended DTB
Signed-off-by: Olof Johansson <olof@lixom.net>
This will delete some redundant calling of sirfsoc_of_pwrc_init() and
sirfsoc_memc_init() for non-CSR platforms if we use multi-platform.
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch also enables RTC alarm as wakeup source after system suspends.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Pawel Moll and Nicolas Pitre:
- Fixes to the existing Vexpress DCSCB backend.
- Lorenzo's minimal SPC driver required by the TC2 MCPM backend.
- The MCPM backend enabling SMP secondary boot and CPU hotplug
on the VExpress TC2 big.LITTLE platform.
- MCPM suspend method to the TC2 backend allowing basic CPU
idle/suspend. The cpuidle driver that hooks into this will be
submitted separately.
* tag 'tc2-pm' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress/TC2: implement PM suspend method
ARM: vexpress/TC2: basic PM support
ARM: vexpress: Add SCC to V2P-CA15_A7's device tree
ARM: vexpress/TC2: add Serial Power Controller (SPC) support
ARM: vexpress/dcscb: fix cache disabling sequences
Signed-off-by: Olof Johansson <olof@lixom.net>
Tegra20 HW appears to have a bug such that PCIe device interrupts,
whether they are legacy IRQs or MSI, are lost when LP2 is enabled. To
work around this, simply disable LP2 if any PCIe devices with interrupts
are present. Detect this via the IRQ domain map operation. This is
slightly over-conservative; if a device with an interrupt is present but
the driver does not actually use them, LP2 will still be disabled.
However, this is a reasonable trade-off which enables a simpler
workaround.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
I'll be taking on maintainership of the Tegra PCIe driver since it's now
moved out of arch/arm/mach-tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The registers PADS_REFCLK_CFG are an array of 16-bit data, one entry per
PCIe root port. For Tegra30, we therefore need to write a 3rd entry in
this array. Doing so makes the mini-PCIe slot on Beaver operate correctly.
While we're at it, add some #defines to partially document the fields
within these 16-bit values.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Introduce a data structure to parameterize the driver according to SoC
generation, add Tegra30 specific code and update the device tree binding
document for Tegra30 support.
Signed-off-by: Jay Agarwal <jagarwal@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move the PCIe driver from arch/arm/mach-tegra into the drivers/pci/host
directory. The motivation is to collect various host controller drivers
in the same location in order to facilitate refactoring.
The Tegra PCIe driver has been largely rewritten, both in order to turn
it into a proper platform driver and to add MSI (based on code by
Krishna Kishore <kthota@nvidia.com>) as well as device tree support.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
[swarren, split DT changes into a separate patch in another branch]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Some platforms (e.g S390) don't use the generic hardirqs code and
therefore do not defined HAVE_GENERIC_HARDIRQS. This prevents using
the irq_set_chip_data() and irq_get_chip_data() functions that are
used for the default implementations of the MSI operations.
So, when CONFIG_GENERIC_HARDIRQS is not enabled, provide another
default implementation of the MSI operations, that simply errors
out. The architecture is responsible for implementing those operations
(which is the case on S390), and cannot use the msi_chip infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that all the needed pieces for DRA7 based SoCs' is present, enable
the build support in omap2plus_defconfig
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The soc_ops for dra7xx devices can be completed reused
from the ones used for omap4 and omap5 devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The DRA7xx is a high-performance, infotainment application device,
based on enhanced OMAP architecture integrated on a 28-nm technology.
Since DRA7 is a platform supported only using DT, the cpu detection
is based on the compatibles passed from DT blobs as suggested here
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-July/187712.html
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
DRA7xx has 8 GPIO banks so that there are 32x8 = 256 GPIOs.
In order for the gpiolib to detect and initialize these
and other TWL GPIOs, ARCH_NR_GPIO is set to 512 using the
kconfig default for DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Describe minimal DT boot machine details for DRA7xx based SoC's. DRA7xx
family is based on dual core ARM CORTEX A15 using GIC as the interrupt controller.
The PRCM and timer infrastructure is reused from OMAP5 and so are the io
descriptor tables.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
All of OMAP5 timer support for clocksource and clockevent is completely
reused across DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The IO descriptor tables for DRA7 are a complete reuse from OMAP5.
A new dra7xx_init_early() does the base address inits.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The PRCM and MPUSS parts of DRA7 devices are quite identical
to OMAP5 so as to reuse all the existing infrastructure around it.
Makefile updates to do just that.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored. Then jumping to "tegra_resume" that was expected to be stored
in PMC_SCRATCH41 to restore CPU context and back to kernel.
Based on the work by: Bo Yan <byan@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* putting SDRAM into self-refresh
* storing some EMC registers and SCLK burst policy
* switching CPU to CLK_M (12MHz OSC)
* switching SCLK to CLK_S (32KHz OSC)
* tunning off PLLM, PLLP and PLLC
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, and PLLC
* restoring some EMC registers and SCLK burst policy
* setting up CCLK burst policy to PLLP
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLP. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLX. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by: Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LP1 suspending mode on Tegra means CPU rail off, devices and PLLs are
clock gated and SDRAM in self-refresh mode. That means the low level LP1
suspending and resuming code couldn't be run on DRAM and the CPU must
switch to the always on clock domain (a.k.a. CLK_M 12MHz oscillator). And
the system clock (SCLK) would be switched to CLK_S, a 32KHz oscillator.
The LP1 low level handling code need to be moved to IRAM area first. And
marking the LP1 mask for indicating the Tegra device is in LP1. The CPU
power timer needs to be re-calculated based on 32KHz that was originally
based on PCLK.
When resuming from LP1, the LP1 reset handler will resume PLLs and then
put DRAM to normal mode. Then jumping to the "tegra_resume" that will
restore full context before back to kernel. The "tegra_resume" handler
was expected to be found in PMC_SCRATCH41 register.
This is common LP1 procedures for Tegra, so we do these jobs mainly in
this patch:
* moving LP1 low level handling code to IRAM
* marking LP1 mask
* copying the physical address of "tegra_resume" to PMC_SCRATCH41
* re-calculate the CPU power timer based on 32KHz
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, replaced IRAM_CODE macro with IO_ADDRESS(TEGRA_IRAM_CODE_AREA)]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
When the system suspends to LP1, the CPU clock source is switched to
CLK_M (12MHz Oscillator) during suspend/resume flow. The CPU clock
source is controlled by the CCLKG_BURST_POLICY register, and hence this
register must be restored during LP1 resume.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
When suspending to LP1 mode, the SYSCLK will be clock gated. And different
board may have different polarity of the request of SYSCLK, this patch
configure the polarity from the DT for the board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add support to the Tegra CPU reset vector to detect whether the CPU is
resuming from LP1 suspend state. If it is, branch to the LP1-specific
resume code.
When Tegra enters the LP1 suspend state, the SDRAM controller is placed
into a self-refresh state. For this reason, we must place the LP1 resume
code into IRAM, so that it is accessible before SDRAM access has been
re-enabled.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This variable is not being used anywhere and it's only forgotten
garbage that should have been removed in the previous commit:
commit 9b6e4c0a58
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Jul 26 10:17:38 2013 -0300
memory: mvebu-devbus: Remove address decoding window workaround
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some PCI drivers may need to adjust the pci_bus structure after it has
been allocated by the Linux PCI core. The PCI core allows
architectures to implement the pcibios_add_bus() and
pcibios_remove_bus() for this purpose. This commit therefore extends
the hw_pci and pci_sys_data structures of the ARM PCI core to allow
PCI drivers to register ->add_bus() and ->remove_bus() in hw_pci,
which will get called when a bus is added or removed from the system.
This will be used for example by the Marvell PCIe driver to connect a
particular PCI bus with its corresponding MSI chip to handle Message
Signaled Interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a very basic registry of msi_chip structures, so that
an IRQ controller driver can register an msi_chip, and a PCIe host
controller can find it, based on a 'struct device_node'.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The new struct msi_chip is used to associated an MSI controller with a
PCI bus. It is automatically handed down from the root to its children
during bus enumeration.
This patch provides default (weak) implementations for the architecture-
specific MSI functions (arch_setup_msi_irq(), arch_teardown_msi_irq()
and arch_msi_check_device()) which check if a PCI device's bus has an
attached MSI chip and forward the call appropriately.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull SCSI fixes from James Bottomley:
"This is three bug fixes: An fnic warning caused by sleeping under a
lock, a major regression with our updated WRITE SAME/UNMAP logic which
caused tons of USB devices (and one RAID card) to cease to function
and a megaraid_sas firmware initialisation problem which causes kdump
failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Don't attempt to send extended INQUIRY command if skip_vpd_pages is set
[SCSI] fnic: BUG: sleeping function called from invalid context during probe
[SCSI] megaraid_sas: megaraid_sas driver init fails in kdump kernel
Pull powerpc fixes from Ben Herrenschmidt:
"This includes small series from Michael Neuling to fix a couple of
nasty remaining problems with the new Power8 support, also targeted at
stable 3.10, without which some new userspace accessible registers
aren't properly context switched, and in some case, can be clobbered
by the user of transactional memory.
Along with that, a few slightly more minor things, such as a missing
Kconfig option to enable handling of denorm exceptions when not
running under a hypervisor (or userspace will randomly crash when
hitting denorms with the vector unit), some nasty bugs in the new
pstore oops code, and other simple bug fixes worth having in now.
Note: I picked up the two powerpc KVM fixes as Alex Graf asked me to
handle KVM bits while he is on vacation. However I'll let him decide
whether they should go to -stable or not when he is back"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/tm: Fix context switching TAR, PPR and DSCR SPRs
powerpc: Save the TAR register earlier
powerpc: Fix context switch DSCR on POWER8
powerpc: Rework setting up H/FSCR bit definitions
powerpc: Fix hypervisor facility unavaliable vector number
powerpc/kvm/book3s_pr: Return appropriate error when allocation fails
powerpc/kvm: Add signed type cast for comparation
powerpc/eeh: Add missing procfs entry for PowerNV
powerpc/pseries: Add backward compatibilty to read old kernel oops-log
powerpc/pseries: Fix buffer overflow when reading from pstore
powerpc: On POWERNV enable PPC_DENORMALISATION by default
Pull s390 kvm fixes from Paolo Bonzini:
"Two fixes for s390"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: fix pfmf non-quiescing control handling
KVM: s390: move kvm_guest_enter,exit closer to sie
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mv64xxx: Document the newly introduced allwinner compatible
i2c: Fix Kontron PLD prescaler calculation
i2c: i2c-mxs: Use DMA mode even for small transfers
Pull btrfs fixes from Chris Mason:
"These are assorted fixes, mostly from Josef nailing down xfstests
runs. Zach also has a long standing fix for problems with readdir
wrapping f_pos (or ctx->pos)
These patches were spread out over different bases, so I rebased
things on top of rc4 and retested overnight"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: don't loop on large offsets in readdir
Btrfs: check to see if root_list is empty before adding it to dead roots
Btrfs: release both paths before logging dir/changed extents
Btrfs: allow splitting of hole em's when dropping extent cache
Btrfs: make sure the backref walker catches all refs to our extent
Btrfs: fix backref walking when we hit a compressed extent
Btrfs: do not offset physical if we're compressed
Btrfs: fix extent buffer leak after backref walking
Btrfs: fix a bug of snapshot-aware defrag to make it work on partial extents
btrfs: fix file truncation if FALLOC_FL_KEEP_SIZE is specified
Pull NFS client bugfixes from Trond Myklebust:
- Stable patch for lockd to fix Oopses due to inappropriate calls to
utsname()->nodename
- Stable patches for sunrpc to fix Oopses on shutdown when using
AF_LOCAL sockets with rpcbind
- Fix memory leak and error checking issues in nfs4_proc_lookup_mountpoint
- Fix a regression with the sync mount option failing to work for nfs4
mounts
- Fix a writeback performance issue when doing cache invalidation
- Remove an incorrect call to nfs_setsecurity in nfs_fhget
* tag 'nfs-for-3.11-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix up nfs4_proc_lookup_mountpoint
NFS: Remove unnecessary call to nfs_setsecurity in nfs_fhget()
NFSv4: Fix the sync mount option for nfs4 mounts
NFS: Fix writeback performance issue on cache invalidation
SUNRPC: If the rpcbind channel is disconnected, fail the call to unregister
SUNRPC: Don't auto-disconnect from the local rpcbind socket
LOCKD: Don't call utsname()->nodename from nlmclnt_setlockargs
Pull nfsd fixes from Bruce Fields:
"Some fixes for a 4.1 feature that in retrospect probably should have
waited for 3.12.... But it appears to be working now"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
nfsd: Fix SP4_MACH_CRED negotiation in EXCHANGE_ID
nfsd4: Fix MACH_CRED NULL dereference
Pull sound fixes from Takashi Iwai:
"A couple of USB-audio fixes that should also go to stable kernels"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: do not trust too-big wMaxPacketSize values
ALSA: 6fire: fix DMA issues with URB transfer_buffer usage
Pull staging driver fixes from Greg KH:
"Here are 3 small fixes for staging/IIO drivers for 3.11-rc5. Nothing
huge, two IIO driver fixes, and a zcache fix. All of these have been
in linux-next for a while"
* tag 'staging-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: zcache: fix "zcache=" kernel parameter
iio: ti_am335x_adc: Fix wrong samples received on 1st read
iio:trigger: Fix use_count race condition
Pull USB fixes from Greg KH:
"Here are 3 small USB fixes for 3.11-rc5.
One is a fix that the ChromeOS developers ran into on some Intel
hardware, one is a build fix, and the last is a MAINTAINERS update to
help people figure out where to send USB network driver patches.
All of these have been in linux-next for a while"
* tag 'usb-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: Add separate section for USB NETWORKING DRIVERS
usb: xhci: add missing dma-mapping.h includes
usb: core: don't try to reset_device() a port that got just disconnected
When btrfs readdir() hits the last entry it sets the readdir offset to a
huge value to stop buggy apps from breaking when the same name is
returned by readdir() with concurrent rename()s.
But unconditionally setting the offset to INT_MAX causes readdir() to
loop returning any entries with offsets past INT_MAX. It only takes a
few hours of constant file creation and removal to create entries past
INT_MAX.
So let's set the huge offset to LLONG_MAX if the last entry has already
overflowed 32bit loff_t. Without large offsets behaviour is identical.
With large offsets 64bit apps will work and 32bit apps will be no more
broken than they currently are if they see large offsets.
Signed-off-by: Zach Brown <zab@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
