IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 82806744fd7dde603b64c151eeddaa4ee62193fd upstream.
swiotlb_find_slots() skips slots according to io tlb aligned mask
calculated from min aligned mask and original physical address
offset. This affects max mapping size. The mapping size can't
achieve the IO_TLB_SEGSIZE * IO_TLB_SIZE when original offset is
non-zero. This will cause system boot up failure in Hyper-V
Isolation VM where swiotlb force is enabled. Scsi layer use return
value of dma_max_mapping_size() to set max segment size and it
finally calls swiotlb_max_mapping_size(). Hyper-V storage driver
sets min align mask to 4k - 1. Scsi layer may pass 256k length of
request buffer with 0~4k offset and Hyper-V storage driver can't
get swiotlb bounce buffer via DMA API. Swiotlb_find_slots() can't
find 256k length bounce buffer with offset. Make swiotlb_max_mapping
_size() take min align mask into account.
Signed-off-by: Tianyu Lan <Tianyu.Lan@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rishabh Bhatnagar <risbhat@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e768c8e34e639cff66a0f175bc4aebf472e4305 upstream.
The v4l2_compat_get_array_args() function can leave uninitialized memory in the
buffer it is passed. So zero it before copying array elements from userspace
into the buffer.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+ff18193ff05f3f87f226@syzkaller.appspotmail.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a99c4474112f49a5459933d8758614002ca0ddc upstream.
Quite often, the HW get stuck in error condition if a stream error
was detected. As documented, the HW should stop immediately and self
reset. There is likely a problem or a miss-understanding of the self
reset mechanism, as unless we make a long pause, the next command
will then report an error even if there is no error in it.
Disabling error detection fixes the issue, and let the decoder continue
after an error. This patch is safe for backport into older kernels.
Fixes: cd33c830448b ("media: rkvdec: Add the rkvdec driver")
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37238699073e7e93f05517e529661151173cd458 upstream.
vb2_core_qbuf and vb2_core_querybuf don't check the range of b->index
controlled by the user.
Fix this by adding range checking code before using them.
Fixes: 57868acc369a ("media: videobuf2: Add new uAPI for DVB streaming I/O")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 77677cdbc2aa4b5d5d839562793d3d126201d18d upstream.
The GHES code calls memory_failure_queue() from IRQ context to queue work
into workqueue and schedule it on the current CPU. Then the work is
processed in memory_failure_work_func() by kworker and calls
memory_failure().
When a page is already poisoned, commit a3f5d80ea401 ("mm,hwpoison: send
SIGBUS with error virutal address") make memory_failure() call
kill_accessing_process() that:
- holds mmap locking of current->mm
- does pagetable walk to find the error virtual address
- and sends SIGBUS to the current process with error info.
However, the mm of kworker is not valid, resulting in a null-pointer
dereference. So check mm when killing the accessing process.
[akpm@linux-foundation.org: remove unrelated whitespace alteration]
Link: https://lkml.kernel.org/r/20220914064935.7851-1-xueshuai@linux.alibaba.com
Fixes: a3f5d80ea401 ("mm,hwpoison: send SIGBUS with error virutal address")
Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com>
Reviewed-by: Miaohe Lin <linmiaohe@huawei.com>
Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Bixuan Cui <cuibixuan@linux.alibaba.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 60bae73708963de4a17231077285bd9ff2f41c44 upstream.
When clearing a PTE the TLB should be flushed whilst still holding the PTL
to avoid a potential race with madvise/munmap/etc. For example consider
the following sequence:
CPU0 CPU1
---- ----
migrate_vma_collect_pmd()
pte_unmap_unlock()
madvise(MADV_DONTNEED)
-> zap_pte_range()
pte_offset_map_lock()
[ PTE not present, TLB not flushed ]
pte_unmap_unlock()
[ page is still accessible via stale TLB ]
flush_tlb_range()
In this case the page may still be accessed via the stale TLB entry after
madvise returns. Fix this by flushing the TLB while holding the PTL.
Fixes: 8c3328f1f36a ("mm/migrate: migrate_vma() unmap page from vma while collecting pages")
Link: https://lkml.kernel.org/r/9f801e9d8d830408f2ca27821f606e09aa856899.1662078528.git-series.apopple@nvidia.com
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reported-by: Nadav Amit <nadav.amit@gmail.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Cc: Alex Sierra <alex.sierra@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: huang ying <huang.ying.caritas@gmail.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Logan Gunthorpe <logang@deltatee.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4eb5bbde3ccb710d3b85bfb13466612e56393369 upstream.
Smatch checker complains that 'secretmem_mnt' dereferencing possible
ERR_PTR(). Let the function return if 'secretmem_mnt' is ERR_PTR, to
avoid deferencing it.
Link: https://lkml.kernel.org/r/20220904074647.GA64291@cloud-MacBookPro
Fixes: 1507f51255c9f ("mm: introduce memfd_secret system call to create "secret" memory areas")
Signed-off-by: Binyi Han <dantengknight@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foudation.org>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Cc: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac22531bbd4af2426c4e29e05594415ccfa365d upstream.
A number of drivers call page_frag_alloc() with a fragment's size >
PAGE_SIZE.
In low memory conditions, __page_frag_cache_refill() may fail the order
3 cache allocation and fall back to order 0; In this case, the cache
will be smaller than the fragment, causing memory corruptions.
Prevent this from happening by checking if the newly allocated cache is
large enough for the fragment; if not, the allocation will fail and
page_frag_alloc() will return NULL.
Link: https://lkml.kernel.org/r/20220715125013.247085-1-mlombard@redhat.com
Fixes: b63ae8ca096d ("mm/net: Rename and move page fragment handling from net/ to mm/")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Cc: Chen Lin <chen45464546@163.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d36424b3b5850bd92f3e89b953a430d7cfc88ef upstream.
Patrick Daly reported the following problem;
NODE_DATA(nid)->node_zonelists[ZONELIST_FALLBACK] - before offline operation
[0] - ZONE_MOVABLE
[1] - ZONE_NORMAL
[2] - NULL
For a GFP_KERNEL allocation, alloc_pages_slowpath() will save the
offset of ZONE_NORMAL in ac->preferred_zoneref. If a concurrent
memory_offline operation removes the last page from ZONE_MOVABLE,
build_all_zonelists() & build_zonerefs_node() will update
node_zonelists as shown below. Only populated zones are added.
NODE_DATA(nid)->node_zonelists[ZONELIST_FALLBACK] - after offline operation
[0] - ZONE_NORMAL
[1] - NULL
[2] - NULL
The race is simple -- page allocation could be in progress when a memory
hot-remove operation triggers a zonelist rebuild that removes zones. The
allocation request will still have a valid ac->preferred_zoneref that is
now pointing to NULL and triggers an OOM kill.
This problem probably always existed but may be slightly easier to trigger
due to 6aa303defb74 ("mm, vmscan: only allocate and reclaim from zones
with pages managed by the buddy allocator") which distinguishes between
zones that are completely unpopulated versus zones that have valid pages
not managed by the buddy allocator (e.g. reserved, memblock, ballooning
etc). Memory hotplug had multiple stages with timing considerations
around managed/present page updates, the zonelist rebuild and the zone
span updates. As David Hildenbrand puts it
memory offlining adjusts managed+present pages of the zone
essentially in one go. If after the adjustments, the zone is no
longer populated (present==0), we rebuild the zone lists.
Once that's done, we try shrinking the zone (start+spanned
pages) -- which results in zone_start_pfn == 0 if there are no
more pages. That happens *after* rebuilding the zonelists via
remove_pfn_range_from_zone().
The only requirement to fix the race is that a page allocation request
identifies when a zonelist rebuild has happened since the allocation
request started and no page has yet been allocated. Use a seqlock_t to
track zonelist updates with a lockless read-side of the zonelist and
protecting the rebuild and update of the counter with a spinlock.
[akpm@linux-foundation.org: make zonelist_update_seq static]
Link: https://lkml.kernel.org/r/20220824110900.vh674ltxmzb3proq@techsingularity.net
Fixes: 6aa303defb74 ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator")
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Patrick Daly <quic_pdaly@quicinc.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: <stable@vger.kernel.org> [4.9+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7afa79a3b35a27a046a2139f8b20bd6b98155c2 upstream.
The block device uses multiple queues to access emmc. There will be up to 3
requests in the hsq of the host. The current code will check whether there
is a request doing recovery before entering the queue, but it will not check
whether there is a request when the lock is issued. The request is in recovery
mode. If there is a request in recovery, then a read and write request is
initiated at this time, and the conflict between the request and the recovery
request will cause the data to be trampled.
Signed-off-by: Wenchao Chen <wenchao.chen@unisoc.com>
Fixes: 511ce378e16f ("mmc: Add MMC host software queue support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220916090506.10662-1-wenchao.chen666@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 35ca91d1338ae158f6dcc0de5d1e86197924ffda upstream.
According to the datasheet [1] at page 377, 4-bit bus width is turned on by
bit 2 of the Bus Width Register. Thus the current bitmask is wrong: define
BUS_WIDTH_4 BIT(1)
BIT(1) does not work but BIT(2) works. This has been verified on real MOXA
hardware with FTSDC010 controller revision 1_6_0.
The corrected value of BUS_WIDTH_4 mask collides with: define BUS_WIDTH_8
BIT(2). Additionally, 8-bit bus width mode isn't supported according to the
datasheet, so let's remove the corresponding code.
[1]
https://bitbucket.org/Kasreyn/mkrom-uc7112lx/src/master/documents/FIC8120_DS_v1.2.pdf
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220907205753.1577434-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea08aec7e77bfd6599489ec430f9f859ab84575a upstream.
Commit 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as
board_ahci_mobile") added an explicit entry for AMD Green Sardine
AHCI controller using the board_ahci_mobile configuration (this
configuration has later been renamed to board_ahci_low_power).
The board_ahci_low_power configuration enables support for low power
modes.
This explicit entry takes precedence over the generic AHCI controller
entry, which does not enable support for low power modes.
Therefore, when commit 1527f69204fe ("ata: ahci: Add Green Sardine
vendor ID as board_ahci_mobile") was backported to stable kernels,
it make some Pioneer optical drives, which was working perfectly fine
before the commit was backported, stop working.
The real problem is that the Pioneer optical drives do not handle low
power modes correctly. If these optical drives would have been tested
on another AHCI controller using the board_ahci_low_power configuration,
this issue would have been detected earlier.
Unfortunately, the board_ahci_low_power configuration is only used in
less than 15% of the total AHCI controller entries, so many devices
have never been tested with an AHCI controller with low power modes.
Fixes: 1527f69204fe ("ata: ahci: Add Green Sardine vendor ID as board_ahci_mobile")
Cc: stable@vger.kernel.org
Reported-by: Jaap Berkhout <j.j.berkhout@staalenberk.nl>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46f8a29272e51b6df7393d58fc5cb8967397ef2b upstream.
If the VDUSE application provides a smaller config space
than the driver expects, the driver may use uninitialized
memory from the stack.
This patch prevents it by initializing the buffer passed by
the driver to store the config value.
This fix addresses CVE-2022-2308.
Cc: stable@vger.kernel.org # v5.15+
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Reviewed-by: Xie Yongji <xieyongji@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Message-Id: <20220831154923.97809-1-maxime.coquelin@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b7329cf5a767c1be38352d43066012e220ad43c upstream.
- Under SRIOV, we need to send REQ_GPU_FINI to the hypervisor
during the suspend time. Furthermore, we cannot request a
mode 1 reset under SRIOV as VF. Therefore, we will skip it
as it is called in suspend_noirq() function.
- In the resume code path, we need to send REQ_GPU_INIT to the
hypervisor and also resume PSP IP block under SRIOV.
Signed-off-by: Bokun Zhang <Bokun.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ef7d362123ecb5bf6d163bb9c7fd6ba2d8c968c upstream.
When we submit a new pair of contexts to ELSP for execution, we start a
timer by which point we expect the HW to have switched execution to the
pending contexts. If the promotion to the new pair of contexts has not
occurred, we declare the executing context to have hung and force the
preemption to take place by resetting the engine and resubmitting the
new contexts.
This can lead to an unfair situation where almost all of the preemption
timeout is consumed by the first context which just switches into the
second context immediately prior to the timer firing and triggering the
preemption reset (assuming that the timer interrupts before we process
the CS events for the context switch). The second context hasn't yet had
a chance to yield to the incoming ELSP (and send the ACk for the
promotion) and so ends up being blamed for the reset.
If we see that a context switch has occurred since setting the
preemption timeout, but have not yet received the ACK for the ELSP
promotion, rearm the preemption timer and check again. This is
especially significant if the first context was not schedulable and so
we used the shortest timer possible, greatly increasing the chance of
accidentally blaming the second innocent context.
Fixes: 3a7a92aba8fb ("drm/i915/execlists: Force preemption")
Fixes: d12acee84ffb ("drm/i915/execlists: Cancel banned contexts on schedule-out")
Reported-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220921135258.1714873-1-andrzej.hajda@intel.com
(cherry picked from commit 107ba1a2c705f4358f2602ec2f2fd821bb651f42)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c6656337852e9f1a4079d172f3fddfbf00868f9 upstream.
This reverts commit a3b884cef873 ("firmware: arm_scmi: Add clock management
to the SCMI power domain").
Using the GENPD_FLAG_PM_CLK tells genpd to gate/ungate the consumer
device's clock(s) during runtime suspend/resume through the PM clock API.
More precisely, in genpd_runtime_resume() the clock(s) for the consumer
device would become ungated prior to the driver-level ->runtime_resume()
callbacks gets invoked.
This behaviour isn't a good fit for all platforms/drivers. For example, a
driver may need to make some preparations of its device in its
->runtime_resume() callback, like calling clk_set_rate() before the
clock(s) should be ungated. In these cases, it's easier to let the clock(s)
to be managed solely by the driver, rather than at the PM domain level.
For these reasons, let's drop the use GENPD_FLAG_PM_CLK for the SCMI PM
domain, as to enable it to be more easily adopted across ARM platforms.
Fixes: a3b884cef873 ("firmware: arm_scmi: Add clock management to the SCMI power domain")
Cc: Nicolas Pitre <npitre@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20220919122033.86126-1-ulf.hansson@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42bc4fafe359ed6b73602b7a2dba0dd99588f8ce upstream.
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1552fd3ef7dbe07208b8ae84a0a6566adf7dfc9d upstream.
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. Fix this up by properly calling
dput().
Link: https://lkml.kernel.org/r/20220902191149.112434-1-sj@kernel.org
Fixes: 75c1c2b53c78b ("mm/damon/dbgfs: support multiple contexts")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4952aa696a9f221c5e34e5961e02fca41ef67ad6 upstream.
The DT parser is dependent on the PCI device being tagged as
device_type = "pci" in order to parse memory ranges properly.
Fix this up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220919092608.813511-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 133e049a3f8c91b175029fb6a59b6039d5e79cba upstream.
Unsanitized pages trigger WARN_ON() unconditionally, which can panic the
whole computer, if /proc/sys/kernel/panic_on_warn is set.
In sgx_init(), if misc_register() fails or misc_register() succeeds but
neither sgx_drv_init() nor sgx_vepc_init() succeeds, then ksgxd will be
prematurely stopped. This may leave unsanitized pages, which will result a
false warning.
Refine __sgx_sanitize_pages() to return:
1. Zero when the sanitization process is complete or ksgxd has been
requested to stop.
2. The number of unsanitized pages otherwise.
Fixes: 51ab30eb2ad4 ("x86/sgx: Replace section->init_laundry_list with sgx_dirty_page_list")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-sgx/20220825051827.246698-1-jarkko@kernel.org/T/#u
Link: https://lkml.kernel.org/r/20220906000221.34286-2-jarkko@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6726d552a6912e88cf63fe2bda87b2efa0efc7d0 upstream.
Access to registers is guarded by ingenic_tcu_{enable,disable}_regs()
so the stop bit can be cleared before accessing a timer channel, but
those functions did not clear the stop bit on SoCs with a global TCU
clock gate.
Testing on the X1000 has revealed that the stop bits must be cleared
_and_ the global TCU clock must be ungated to access timer registers.
This appears to be the norm on Ingenic SoCs, and is specified in the
documentation for the X1000 and numerous JZ47xx SoCs.
If the stop bit isn't cleared, register writes don't take effect and
the system can be left in a broken state, eg. the watchdog timer may
not run.
The bug probably went unnoticed because stop bits are zeroed when
the SoC is reset, and the kernel does not set them unless a timer
gets disabled at runtime. However, it is possible that a bootloader
or a previous kernel (if using kexec) leaves the stop bits set and
we should not rely on them being cleared.
Fixing this is easy: have ingenic_tcu_{enable,disable}_regs() always
clear the stop bit, regardless of the presence of a global TCU gate.
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Fixes: 4f89e4b8f121 ("clk: ingenic: Add driver for the TCU clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220617122254.738900-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81d192c2ce74157e717e1fc4b68791f82f7499d4 upstream.
As Jacob noticed, the optimization introduced in 387da6bc7a82 ("can:
c_can: cache frames to operate as a true FIFO") doesn't properly work
on C_CAN, but on D_CAN IP cores. The exact reasons are still unknown.
For now disable caching if CAN frames in the TX path for C_CAN cores.
Fixes: 387da6bc7a82 ("can: c_can: cache frames to operate as a true FIFO")
Link: https://lore.kernel.org/all/20220928083354.1062321-1-mkl@pengutronix.de
Link: https://lore.kernel.org/all/15a8084b-9617-2da1-6704-d7e39d60643b@gmail.com
Reported-by: Jacob Kroon <jacob.kroon@gmail.com>
Tested-by: Jacob Kroon <jacob.kroon@gmail.com>
Cc: stable@vger.kernel.org # v5.15
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e62563db857f81d75c5726a35bc0180bed6d1540 upstream.
Both i.MX6 and i.MX8 reference manuals list 0xBF8 as SNVS_HPVIDR1
(chapters 57.9 and 6.4.5 respectively).
Without this, trying to read the revision number results in 0 on
all revisions, causing the i.MX6 quirk to apply on all platforms,
which in turn causes the driver to synthesise power button release
events instead of passing the real one as they happen even on
platforms like i.MX8 where that's not wanted.
Fixes: 1a26c920717a ("Input: snvs_pwrkey - send key events for i.MX6 S, DL and Q")
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4599101.ElGaqSPkdT@pliszka
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31f87f705b3c1635345d8e8a493697099b43e508 upstream.
If any software has interacted with the USB4 registers before the Linux
USB4 CM runs, it may have modified the plug events delay. It has been
observed that if this value too large, it's possible that hotplugged
devices will negotiate a fallback mode instead in Linux.
To prevent this, explicitly align the plug events delay with the USB4
spec value of 10ms.
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 415ba26cb73f7d22a892043301b91b57ae54db02 upstream.
Sink only devices do not have any source capabilities, so
the driver should not warn about that. Also DRP (Dual Role
Power) capable devices, such as USB Type-C docking stations,
do not return any source capabilities unless they are
plugged to a power supply themselves.
Fixes: 1f4642b72be7 ("usb: typec: ucsi: Retrieve all the PDOs instead of just the first 4")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922145924.80667-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e00b488e813f0f1ad9f778e771b7cd2fe2877023 upstream.
The UAS mode of Hiksemi USB_HDD is reported to fail to work on several
platforms with the following error message, then after re-connecting the
device will be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901185-21067-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a625a4b8806cc1e928b7dd2cca1fee709c9de56e upstream.
The UAS mode of Hiksemi is reported to fail to work on several platforms
with the following error message, then after re-connecting the device will
be offlined and not working at all.
[ 592.518442][ 2] sd 8:0:0:0: [sda] tag#17 uas_eh_abort_handler 0 uas-tag 18
inflight: CMD
[ 592.527575][ 2] sd 8:0:0:0: [sda] tag#17 CDB: Write(10) 2a 00 03 6f 88 00 00
04 00 00
[ 592.536330][ 2] sd 8:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 1
inflight: CMD
[ 592.545266][ 2] sd 8:0:0:0: [sda] tag#0 CDB: Write(10) 2a 00 07 44 1a 88 00
00 08 00
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly,so we need to fall-back to usb-storage.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Hongling Zeng <zenghongling@kylinos.cn>
Link: https://lore.kernel.org/r/1663901173-21020-1-git-send-email-zenghongling@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit df02452f3df069a59bc9e69c84435bf115cb6e37 ]
cgroup has to be one kernfs dir, otherwise kernel panic is caused,
especially cgroup id is provide from userspace.
Reported-by: Marco Patalano <mpatalan@redhat.com>
Fixes: 6b658c4863c1 ("scsi: cgroup: Add cgroup_get_from_id()")
Cc: Muneendra <muneendra.kumar@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Cc: stable@vger.kernel.org # v5.14+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit be288169712f3dea0bc6b50c00b3ab53d85f1435 ]
Currently cgroup_get_from_path() and cgroup_get_from_id() grab
cgroup_mutex before traversing the default hierarchy to find the
kernfs_node corresponding to the path/id and then extract the linked
cgroup. Since cgroup_mutex is still held, it is guaranteed that the
cgroup will be alive and the reference can be taken on it.
However similar guarantee can be provided without depending on the
cgroup_mutex and potentially reducing avenues of cgroup_mutex contentions.
The kernfs_node's priv pointer is RCU protected pointer and with just
rcu read lock we can grab the reference on the cgroup without
cgroup_mutex. So, remove cgroup_mutex from them.
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stable-dep-of: df02452f3df0 ("cgroup: cgroup_get_from_id() must check the looked-up kn is a directory")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91502a9a0b0d5252cf3f32ebd898823c2f5aadab ]
There are several PCI ids associated with HP EliteBook 855 G8 Notebook
PC. Commit 0e68c4b11f1e6 ("ALSA: hda/realtek: fix mute/micmute LEDs for
HP 855 G8") covers 0x103c:0x8896, while this commit covers 0x103c:0x8895
which needs some additional work on top of the quirk from 0e68c4b11f1e6.
Note that the device can boot up with working speakers and micmute LED
without this patch, but the success rate would be quite low (order of
16 working boots across 709 boots) at least for the built-in drivers
scenario. This also means that there are some timing issues during early
boot and this patch is a workaround.
With this patch applied speakers and headphones are consistenly working,
as well as mute/micmute LEDs and the internal microphone.
Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Link: https://lore.kernel.org/r/20220114165050.ouw2nknuspclynro@localhost.localdomain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 496322302bf1 ("ALSA: hda/realtek: Add a quirk for HP OMEN 16 (8902) mute LED")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f89e409402e2aeb3bc3aa44d2b7a597959e4e6af ]
Nvidia HDA HW expects infoframe data bytes order same for both
HDMI and DP i.e infoframe data starts from 5th bytes offset. As
dp infoframe structure has 4th byte as valid infoframe data, use
hdmi infoframe structure for nvidia dp infoframe to match HW behvaior.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220913065818.13015-1-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ead3d3c5b54f76da79c079e61bacb4279ec56965 ]
We fixed the potential deadlock at dynamic unbinding the HD-audio
codec at the commit 7206998f578d ("ALSA: hda: Fix potential deadlock
at codec unbinding"), but ironically, this caused another potential
deadlock. The current code uses refcount_dec() and waits for the
pending task with wait_event for dropping the refcount to 0. This
works fine when PCMs are assigned and actually waiting for the
refcount drop.
Meanwhile, when there was no PCM assigned, the refcount_dec() call
itself was supposed to drop to zero -- alas, it doesn't in reality;
refcount_dec() complains, spews kernel warning and it saturates
instead of dropping to 0, due to the nature of refcount_dec()
implementation. This eventually blocks the wait_event() wakeup and
the code get stuck there.
For avoiding the problem, we call refcount_dec_and_test() and skips
the sync-wait if it already reaches to zero.
The patch does a slight code reshuffling to make sure to invoke other
disconnect calls before the sync-wait, too.
Fixes: 7206998f578d ("ALSA: hda: Fix potential deadlock at codec unbinding")
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/YxtflWQnslMHVlU7@intel.com
Link: https://lore.kernel.org/r/20220910142550.28494-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37c4fd0db7c961145d9d1909ecab386fdf703c26 ]
The HD-audio codec driver remove may happen also at dynamically
unbinding during operation, hence it needs manual triggers of
snd_device_disconnect() calls, while it's missing for the jack objects
that are associated with the codec.
This patch adds the manual disconnection call for jacks when the
remove happens without card->shutdown (i.e. not under the full
removal).
Link: https://lore.kernel.org/r/20211117133040.20272-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: ead3d3c5b54f ("ALSA: hda: Fix hang at HD-audio codec unbinding due to refcount saturation")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a9f2a2931d0e197ab28c6007966053fdababd53f upstream.
Curently we don't use any preallocation when a file is already closed
when allocating blocks (from writeback code when converting delayed
allocation). However for small files, using locality group preallocation
is actually desirable as that is not specific to a particular file.
Rather it is a method to pack small files together to reduce
fragmentation and for that the fact the file is closed is actually even
stronger hint the file would benefit from packing. So change the logic
to allow locality group preallocation in this case.
Fixes: 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning")
CC: stable@kernel.org
Reported-and-tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/all/0d81a7c2-46b7-6010-62a4-3e6cfc1628d6@i2se.com/
Link: https://lore.kernel.org/r/20220908092136.11770-4-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1940265ede6683f6317cba0d428ce6505eaca944 upstream.
mb_set_largest_free_order() updates lists containing groups with largest
chunk of free space of given order. The way it updates it leads to
always moving the group to the tail of the list. Thus allocations
looking for free space of given order effectively end up cycling through
all groups (and due to initialization in last to first order). This
spreads allocations among block groups which reduces performance for
rotating disks or low-end flash media. Change
mb_set_largest_free_order() to only update lists if the order of the
largest free chunk in the group changed.
Fixes: 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning")
CC: stable@kernel.org
Reported-and-tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/all/0d81a7c2-46b7-6010-62a4-3e6cfc1628d6@i2se.com/
Link: https://lore.kernel.org/r/20220908092136.11770-2-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4fca50d440cc5d4dc570ad5484cc0b70b381bc2a upstream.
One of the side-effects of mb_optimize_scan was that the optimized
functions to select next group to try were called even before we tried
the goal group. As a result we no longer allocate files close to
corresponding inodes as well as we don't try to expand currently
allocated extent in the same group. This results in reaim regression
with workfile.disk workload of upto 8% with many clients on my test
machine:
baseline mb_optimize_scan
Hmean disk-1 2114.16 ( 0.00%) 2099.37 ( -0.70%)
Hmean disk-41 87794.43 ( 0.00%) 83787.47 * -4.56%*
Hmean disk-81 148170.73 ( 0.00%) 135527.05 * -8.53%*
Hmean disk-121 177506.11 ( 0.00%) 166284.93 * -6.32%*
Hmean disk-161 220951.51 ( 0.00%) 207563.39 * -6.06%*
Hmean disk-201 208722.74 ( 0.00%) 203235.59 ( -2.63%)
Hmean disk-241 222051.60 ( 0.00%) 217705.51 ( -1.96%)
Hmean disk-281 252244.17 ( 0.00%) 241132.72 * -4.41%*
Hmean disk-321 255844.84 ( 0.00%) 245412.84 * -4.08%*
Also this is causing huge regression (time increased by a factor of 5 or
so) when untarring archive with lots of small files on some eMMC storage
cards.
Fix the problem by making sure we try goal group first.
Fixes: 196e402adf2e ("ext4: improve cr 0 / cr 1 group scanning")
CC: stable@kernel.org
Reported-and-tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Link: https://lore.kernel.org/all/20220727105123.ckwrhbilzrxqpt24@quack3/
Link: https://lore.kernel.org/all/0d81a7c2-46b7-6010-62a4-3e6cfc1628d6@i2se.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220908092136.11770-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80fa46d6b9e7b1527bfd2197d75431fd9c382161 upstream.
This patch avoids threads live-locking for hours when a large number
threads are competing over the last few free extents as they blocks
getting added and removed from preallocation pools. From our bug
reporter:
A reliable way for triggering this has multiple writers
continuously write() to files when the filesystem is full, while
small amounts of space are freed (e.g. by truncating a large file
-1MiB at a time). In the local filesystem, this can be done by
simply not checking the return code of write (0) and/or the error
(ENOSPACE) that is set. Over NFS with an async mount, even clients
with proper error checking will behave this way since the linux NFS
client implementation will not propagate the server errors [the
write syscalls immediately return success] until the file handle is
closed. This leads to a situation where NFS clients send a
continuous stream of WRITE rpcs which result in ERRNOSPACE -- but
since the client isn't seeing this, the stream of writes continues
at maximum network speed.
When some space does appear, multiple writers will all attempt to
claim it for their current write. For NFS, we may see dozens to
hundreds of threads that do this.
The real-world scenario of this is database backup tooling (in
particular, github.com/mdkent/percona-xtrabackup) which may write
large files (>1TiB) to NFS for safe keeping. Some temporary files
are written, rewound, and read back -- all before closing the file
handle (the temp file is actually unlinked, to trigger automatic
deletion on close/crash.) An application like this operating on an
async NFS mount will not see an error code until TiB have been
written/read.
The lockup was observed when running this database backup on large
filesystems (64 TiB in this case) with a high number of block
groups and no free space. Fragmentation is generally not a factor
in this filesystem (~thousands of large files, mostly contiguous
except for the parts written while the filesystem is at capacity.)
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 613c5a85898d1cd44e68f28d65eccf64a8ace9cf upstream.
Currently the Orlov inode allocator searches for free inodes for a
directory only in flex block groups with at most inodes_per_group/16
more directory inodes than average per flex block group. However with
growing size of flex block group this becomes unnecessarily strict.
Scale allowed difference from average directory count per flex block
group with flex block group size as we do with other metrics.
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/all/0d81a7c2-46b7-6010-62a4-3e6cfc1628d6@i2se.com/
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220908092136.11770-3-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67feaba413ec68daf4124e9870878899b4ed9a0e upstream.
The "hmem" platform-devices that are created to represent the
platform-advertised "Soft Reserved" memory ranges end up inserting a
resource that causes the iomem_resource tree to look like this:
340000000-43fffffff : hmem.0
340000000-43fffffff : Soft Reserved
340000000-43fffffff : dax0.0
This is because insert_resource() reparents ranges when they completely
intersect an existing range.
This matters because code that uses region_intersects() to scan for a
given IORES_DESC will only check that top-level 'hmem.0' resource and
not the 'Soft Reserved' descendant.
So, to support EINJ (via einj_error_inject()) to inject errors into
memory hosted by a dax-device, be sure to describe the memory as
IORES_DESC_SOFT_RESERVED. This is a follow-on to:
commit b13a3e5fd40b ("ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP")
...that fixed EINJ support for "Soft Reserved" ranges in the first
instance.
Fixes: 262b45ae3ab4 ("x86/efi: EFI soft reservation to E820 enumeration")
Reported-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Tested-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Omar Avelar <omar.avelar@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/166397075670.389916.7435722208896316387.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e176d47160cec8bcaa28d9aa06926d72d54237c upstream.
We mustn't call nfs_wb_all() on anything other than a regular file.
Furthermore, we can exit early when we don't hold a delegation.
Reported-by: David Wysochanski <dwysocha@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit abbc7a3dafb91b9d4ec56b70ec9a7520f8e13334 ]
Some asics still support non-atomic code paths.
Fixes: 66f99628eb2440 ("drm/amdgpu: use dirty framebuffer helper")
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f071ec327b04c83d47637c5e5c2199b39899ca ]
The i2c-mlxbf.c driver is currently broken because there is a bug
in the calculation of the frequency. core_f, core_r and core_od
are components read from hardware registers and are used to
compute the frequency used to compute different timing parameters.
The shifting mechanism used to get core_f, core_r and core_od is
wrong. Use FIELD_GET to mask and shift the bitfields properly.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de24aceb07d426b6f1c59f33889d6a964770547b ]
memcpy() is called in a loop while 'operation->length' upper bound
is not checked and 'data_idx' also increments.
Fixes: b5b5b32081cd206b ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a5be6d1340c0fefcee8a6489cff7fd88a0d5b85 ]
Correct the base address used during io write.
This bug had no impact over the overall functionality of the read and write
transactions. MLXBF_I2C_CAUSE_OR_CLEAR=0x18 so writing to (smbus->io + 0x18)
instead of (mst_cause->ioi + 0x18) actually writes to the sc_low_timeout
register which just sets the timeout value before a read/write aborts.
Fixes: b5b5b32081cd206b (i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC)
Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
