IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The Radxa ROCK 3C is a similar board to the
Radxa ROCK 3A with the Rockchip RK3566 SoC.
Add devicetree binding documentation for it.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20240428123618.72170-2-amadeus@jmu.edu.cn
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Apart from the host-only usb3 controller (host2) the rk3588 also provides
two dual-role controllers. On the Tiger-Haikou combination these are
connected to the lower usb3-host port in host-only mode and the micro-usb3
port for dual-role operation.
Add the necessary controllers, phys to the Tiger-Haikou board and enable
the usb-id extcon.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Q7 standard specifies a usb-id pin on the connector to distiuish
between host and device mode. Model this via the usb-id extcon binding.
While the pin is part of the Q7 standard, so part of the module, the
extcon stays disabled in the som dtsi and will only be enabled in a
baseboard using it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The comment for the host2_xhci points to the wrong port on the board.
The upper usb3 port is the correct one, so fix the comment to prevent
confusion.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422163951.2604273-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
gpio_pwrctrl2 gets duplicated by both rk806_dvs1_null and rk806_dvs2_null
gpio_pwrctrl1 is unset. This typo appears in multiple files. Let's fix them.
Note: I haven't had the chance to test them all because I don't own all
of these boards (obviously). Please test if it's needed.
Signed-off-by: Jing Luo <jing@jing.rocks>
Link: https://lore.kernel.org/r/20240420130355.639406-1-jing@jing.rocks
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct the model names of a few Pine64 boards and devices, according
to their official names used on the Pine64 wiki. This ensures consistency
between the officially used names and the names in the source code.
Cc: Marek Kraus <gamiee@pine64.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/06ce014a1dedff11a785fe523056b3b8ffdf21ee.1713832790.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Correct the descriptions of a few Pine64 boards and devices, according
to their official names used on the Pine64 wiki. This ensures consistency
between the officially used names and the names in the source code.
Cc: Marek Kraus <gamiee@pine64.org>
Signed-off-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/ec124dab2b1a8776aa39177ecce34babca3a50e2.1713832790.git.dsimic@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Jaguar SBC provides an M.2 slot connected to the pcie3 controller.
In contrast to a number of other boards the pcie-refclk is gpio-controlled,
so the necessary clock and is added to the list of pcie3 clocks.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240423074956.2622318-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The association of uart2 to the q7-uart pins is part of the module
itself and not the baseboard used. Therefore move the pinctrl over
to the tiger dtsi.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Link: https://lore.kernel.org/r/20240422143356.2596414-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the USB-C port on the Indiedroid Nova board. This
port supports USB-C DP Alt mode (not implemented yet in drivers),
but works as a USB XHCI/EHCI/OHCI port.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240418173627.1368494-1-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable full support (XHCI, EHCI, OHCI) for the lower USB3 port from
Radxa Rock 5 Model B. The upper one is already supported.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-11-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable full support (XHCI, EHCI, OHCI) for the upper USB3 port from
Radxa Rock 5 Model A. The lower one is already supported.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20240408225109.128953-10-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Khadas Edge 2 exposes IR receiver pins as same as TF card via EXTIO. The
IR receiver is connected to MCU and SoC.
The board also has 2 PWM RGB leds. One is controlled by MCU and the
other is controlled by SoC. This commit adds support for the led
controlled by SoC using pwm-leds.
Signed-off-by: Muhammed Efe Cetin <efectn@protonmail.com>
Link: https://lore.kernel.org/r/335629f57e593e20418a4a55a1e662505640cbde.1708381247.git.efectn@protonmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for the GameForce Chi, which is a handheld gaming console
from GameForce with a Rockchip RK3326 SoC. The device has a 640x480
3.5" dual-lane DSI display, one analog joystick connected to the SoC
SARADC controller and a second analog joystick connected to an unknown
UART based ADC, a single SD card slot, a single USB-C port for
charging, and onboard RTL8723BS WiFi/Bluetooth combo, multiple face
buttons, and an array of R/G/B LEDs used for key backlighting.
The vendor was unable to provide details on the unknown UART based
ADC which I have documented via a comment in the device-tree, and
the vendor also does not have available Bluetooth firmware (the BT
was not previously working on the vendor's OS, this has also been
noted in a device-tree comment).
Aside from the right analog ADC joystick and bluetooth all hardware has
been tested and is working as expected.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325134959.11807-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The GameForce Chi is a handheld gaming device from GameForce powered
by the Rockchip RK3326 SoC.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240325134959.11807-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some Powkiddy model names begin with the company "Powkiddy" and others
simply list the model number. Make this consistent across the device
lineup by including the manufacturer in the model name.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325175133.19393-4-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Some Anbernic model names begin with the company "Anbernic" and others
simply list the model number. Make this consistent across the device
lineup by including the manufacturer in the model name.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325143729.83852-5-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add additional properties for the SDMMC2 node. Based on user feedback
these help correct some issues with probing the WiFi hardware.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20240325143729.83852-2-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
FET3588-C is an System on Module made by Forlinx based on Rockchip RK3588.
This SoM used by OK3588-C Board.
FET3588-C features:
- Rockchip RK3588
- LPDDR4 4/8 GB
- eMMC 32/64 GB
Add support for Forlinx FET3588-C SoM.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Link: https://lore.kernel.org/r/20240403151229.30577-3-dmt.yashin@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
FET3588-C is an System on Module made by Forlinx based on Rockchip RK3588.
This SoM used by OK3588-C Board.
FET3588-C features:
- Rockchip RK3588
- LPDDR4 4/8 GB
- eMMC 32/64 GB
Add devicetree binding for Forlinx FET3588-C SoM.
Signed-off-by: Dmitry Yashin <dmt.yashin@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240403151229.30577-2-dmt.yashin@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MECSBC is a single board computer for blood analysis machines from
RR-Mechatronics, designed and manufactured by Protonic Holland, based on
the Rockchip RK3568 SoC.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240405-protonic-mecsbc-v2-2-0a6fedc78b9f@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
MECSBC is a single board computer for blood analysis machines from
RR-Mechatronics, designed and manufactured by Protonic Holland, based on
the Rockchip RK3568 SoC.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20240405-protonic-mecsbc-v2-1-0a6fedc78b9f@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Fix the ordering of the main nodes by sorting them alphabetically and
then the ones with a memory address sequentially by that address.
Signed-off-by: Diederik de Haas <didi.debian@cknow.org>
Link: https://lore.kernel.org/r/20240406172821.34173-1-didi.debian@cknow.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 8b5c2b45b8f0 disabled the internal pull-down for the strobe line
causing I/O errors in HS400 mode for various eMMC modules.
Enable the internal strobe pull-down for the ROCK 4C+ board. Also re-enable
HS400 mode, that was replaced with HS200 mode as a workaround for the
stability issues in:
2bd1d2dd808c ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+").
Fixes: 8b5c2b45b8f0 ("phy: rockchip: set pulldown for strobe line in dts")
Signed-off-by: Folker Schwesinger <dev@folker-schwesinger.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240327192641.14220-3-dev@folker-schwesinger.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 8b5c2b45b8f0 disabled the internal pull-down for the strobe line
causing I/O errors in HS400 mode for various eMMC modules.
Enable the internal strobe pull-down for ROCK Pi 4 boards. Also re-enable
HS400 mode, that was replaced with HS200 mode as a workaround for the
stability issues in:
cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4").
This was tested on ROCK 4SE and ROCK Pi 4B+.
Fixes: 8b5c2b45b8f0 ("phy: rockchip: set pulldown for strobe line in dts")
Signed-off-by: Folker Schwesinger <dev@folker-schwesinger.de>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240327192641.14220-2-dev@folker-schwesinger.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
