IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 5c7aa13210c3abdd34fd421f62347665ec6eb551 ]
hsr_register_frame_out() compares new sequence_nr vs the old one
recorded in hsr_node::seq_out and if the new sequence_nr is higher then
it will be written to hsr_node::seq_out as the new value.
This operation isn't locked so it is possible that two frames with the
same sequence number arrive (via the two slave devices) and are fed to
hsr_register_frame_out() at the same time. Both will pass the check and
update the sequence counter later to the same value. As a result the
content of the same packet is fed into the stack twice.
This was noticed by running ping and observing DUP being reported from
time to time.
Instead of using the hsr_priv::seqnr_lock for the whole receive path (as
it is for sending in the master node) add an additional lock that is only
used for sequence number checks and updates.
Add a per-node lock that is used during sequence number reads and
updates.
Fixes: f421436a591d3 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06afd2c31d338fa762548580c1bf088703dd1e03 ]
Sending frames via the hsr (master) device requires a sequence number
which is tracked in hsr_priv::sequence_nr and protected by
hsr_priv::seqnr_lock. Each time a new frame is sent, it will obtain a
new id and then send it via the slave devices.
Each time a packet is sent (via hsr_forward_do()) the sequence number is
checked via hsr_register_frame_out() to ensure that a frame is not
handled twice. This make sense for the receiving side to ensure that the
frame is not injected into the stack twice after it has been received
from both slave ports.
There is no locking to cover the sending path which means the following
scenario is possible:
CPU0 CPU1
hsr_dev_xmit(skb1) hsr_dev_xmit(skb2)
fill_frame_info() fill_frame_info()
hsr_fill_frame_info() hsr_fill_frame_info()
handle_std_frame() handle_std_frame()
skb1's sequence_nr = 1
skb2's sequence_nr = 2
hsr_forward_do() hsr_forward_do()
hsr_register_frame_out(, 2) // okay, send)
hsr_register_frame_out(, 1) // stop, lower seq duplicate
Both skbs (or their struct hsr_frame_info) received an unique id.
However since skb2 was sent before skb1, the higher sequence number was
recorded in hsr_register_frame_out() and the late arriving skb1 was
dropped and never sent.
This scenario has been observed in a three node HSR setup, with node1 +
node2 having ping and iperf running in parallel. From time to time ping
reported a missing packet. Based on tracing that missing ping packet did
not leave the system.
It might be possible (didn't check) to drop the sequence number check on
the sending side. But if the higher sequence number leaves on wire
before the lower does and the destination receives them in that order
and it will drop the packet with the lower sequence number and never
inject into the stack.
Therefore it seems the only way is to lock the whole path from obtaining
the sequence number and sending via dev_queue_xmit() and assuming the
packets leave on wire in the same order (and don't get reordered by the
NIC).
Cover the whole path for the master interface from obtaining the ID
until after it has been forwarded via hsr_forward_skb() to ensure the
skbs are sent to the NIC in the order of the assigned sequence numbers.
Fixes: f421436a591d3 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5c7652eb16fa203d82546e0285136d7b321ffa9 ]
The hsr device is a software device. Its
net_device_ops::ndo_start_xmit() routine will process the packet and
then pass the resulting skb to dev_queue_xmit().
During processing, hsr acquires a lock with spin_lock_bh()
(hsr_add_node()) which needs to be promoted to the _irq() suffix in
order to avoid a potential deadlock.
Then there are the warnings in dev_queue_xmit() (due to
local_bh_disable() with disabled interrupts) left.
Instead trying to address those (there is qdisc and…) for netpoll sake,
just disable netpoll on hsr.
Disable netpoll on hsr and replace the _irqsave() locking with _bh().
Fixes: f421436a591d3 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c74d9f79ec4299365bbe803baa736ae0068179e ]
Due to the hashed-MAC optimisation one problem become visible:
hsr_handle_sup_frame() walks over the list of available nodes and merges
two node entries into one if based on the information in the supervision
both MAC addresses belong to one node. The list-walk happens on a RCU
protected list and delete operation happens under a lock.
If the supervision arrives on both slave interfaces at the same time
then this delete operation can occur simultaneously on two CPUs. The
result is the first-CPU deletes the from the list and the second CPUs
BUGs while attempting to dereference a poisoned list-entry. This happens
more likely with the optimisation because a new node for the mac_B entry
is created once a packet has been received and removed (merged) once the
supervision frame has been received.
Avoid removing/ cleaning up a hsr_node twice by adding a `removed' field
which is set to true after the removal and checked before the removal.
Fixes: f266a683a4804 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5aa2820177af650293b2f9f1873c1f6f8e4ad7a4 ]
hsr_forward_skb() a skb and keeps information in an on-stack
hsr_frame_info. hsr_get_node() assigns hsr_frame_info::node_src which is
from a RCU list. This pointer is used later in hsr_forward_do().
I don't see a reason why this pointer can't vanish midway since there is
no guarantee that hsr_forward_skb() is invoked from an RCU read section.
Use rcu_read_lock() to protect hsr_frame_info::node_src from its
assignment until it is no longer used.
Fixes: f266a683a4804 ("net/hsr: Better frame dispatch")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e012764cebf6e33097f6833ff15a936fbe7b846c ]
The hlist optimisation (which not only uses hlist_head instead of
list_head but also splits hsr_priv::node_db into an array of 256 slots)
does not consider the "node merge":
Upon starting the hsr network (with three nodes) a packet that is
sent from node1 to node3 will also be sent from node1 to node2 and then
forwarded to node3.
As a result node3 will receive 2 packets because it is not able
to filter out the duplicate. Each packet received will create a new
struct hsr_node with macaddress_A only set the MAC address it received
from (the two MAC addesses from node1).
At some point (early in the process) two supervision frames will be
received from node1. They will be processed by hsr_handle_sup_frame()
and one frame will leave early ("Node has already been merged") and does
nothing. The other frame will be merged as portB and have its MAC
address written to macaddress_B and the hsr_node (that was created for
it as macaddress_A) will be removed.
From now on HSR is able to identify a duplicate because both packets
sent from one node will result in the same struct hsr_node because
hsr_get_node() will find the MAC address either on macaddress_A or
macaddress_B.
Things get tricky with the optimisation: If sender's MAC address is
saved as macaddress_A then the lookup will work as usual. If the MAC
address has been merged into macaddress_B of another hsr_node then the
lookup won't work because it is likely that the data structure is in
another bucket. This results in creating a new struct hsr_node and not
recognising a possible duplicate.
A way around it would be to add another hsr_node::mac_list_B and attach
it to the other bucket to ensure that this hsr_node will be looked up
either via macaddress_A _or_ macaddress_B.
I however prefer to revert it because it sounds like an academic problem
rather than real life workload plus it adds complexity. I'm not an HSR
expert with what is usual size of a network but I would guess 40 to 60
nodes. With 10.000 nodes and assuming 60us for pass-through (from node
to node) then it would take almost 600ms for a packet to almost wrap
around which sounds a lot.
Revert the hash MAC addresses optimisation.
Fixes: 4acc45db71158 ("net: hsr: use hlist_head instead of list_head for mac addresses")
Cc: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d676d3a3717cf726d3affedbe5ba98fc4ccad7b3 ]
Currently div2 value is applied to the wrong bits. This is caused by a
bug in the code where the shift is done only for lpl, for anything
else the mask is not shifted to the correct bits.
Fix this by correctly shift if lpl is not supported.
Fixes: 4d7dc77babfe ("clk: qcom: Add support for Krait clocks")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221108215625.30186-1-ansuelsmth@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff1ccf59eaffd192efe21f7de9fb0c130faf1b1b ]
The sc7180 lpass clock controller's pm_runtime usage wasn't broken
quite as spectacularly as the sc7280's pm_runtime usage, but it was
still broken. Putting some printouts in at boot showed me this (with
serial console enabled, which makes the prints slow and thus changes
timing):
[ 3.109951] DOUG: my_pm_clk_resume, usage=1
[ 3.114767] DOUG: my_pm_clk_resume, usage=1
[ 3.664443] DOUG: my_pm_clk_suspend, usage=0
[ 3.897566] DOUG: my_pm_clk_suspend, usage=0
[ 3.910137] DOUG: my_pm_clk_resume, usage=1
[ 3.923217] DOUG: my_pm_clk_resume, usage=0
[ 4.440116] DOUG: my_pm_clk_suspend, usage=-1
[ 4.444982] DOUG: my_pm_clk_suspend, usage=0
[ 14.170501] DOUG: my_pm_clk_resume, usage=1
[ 14.176245] DOUG: my_pm_clk_resume, usage=0
...or this w/out serial console:
[ 0.556139] DOUG: my_pm_clk_resume, usage=1
[ 0.556279] DOUG: my_pm_clk_resume, usage=1
[ 1.058422] DOUG: my_pm_clk_suspend, usage=-1
[ 1.058464] DOUG: my_pm_clk_suspend, usage=0
[ 1.186250] DOUG: my_pm_clk_resume, usage=1
[ 1.186292] DOUG: my_pm_clk_resume, usage=0
[ 1.731536] DOUG: my_pm_clk_suspend, usage=-1
[ 1.731557] DOUG: my_pm_clk_suspend, usage=0
[ 10.288910] DOUG: my_pm_clk_resume, usage=1
[ 10.289496] DOUG: my_pm_clk_resume, usage=0
It seems to be doing roughly the right sequence of calls, but just
like with sc7280 this is more by luck than anything. Having a usage of
-1 is just not OK.
Let's fix this like we did with sc7280.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Fixes: ce8c195e652f ("clk: qcom: lpasscc: Introduce pm autosuspend for SC7180")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104064055.2.I49b25b9bda9430fc7ea21e5a708ca5a0aced2798@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d470be3c4f30b4666e43eef6bab80f543563cdb0 ]
The pm_runtime usage in lpass-sc7280 was broken in quite a few
ways. Specifically:
1. At the end of probe it called "put" twice. This is a no-no and will
end us up with a negative usage count. Even worse than calling
"put" twice, it never called "get" once. Thus after bootup it could
be seen that the runtime usage of the devices managed by this
driver was -2.
2. In some error cases it manually called pm_runtime_disable() even
though it had previously used devm_add_action_or_reset() to set
this up to be called automatically. This meant that in these error
cases we'd double-call pm_runtime_disable().
3. It forgot to call undo pm_runtime_use_autosuspend(), which can
sometimes have subtle problems (and the docs specifically mention
that you need to undo this function).
Overall the above seriously calls into question how this driver is
working. It seems like a combination of "it doesn't", "by luck", and
"because of the weirdness of runtime_pm". Specifically I put a
printout to the serial console every time the runtime suspend/resume
was called for the two devices created by this driver (I wrapped the
pm_clk calls). When I had serial console enabled, I found that the
calls got resumed at bootup (when the clk core probed and before our
double-put) and then never touched again. That's no good.
[ 0.829997] DOUG: my_pm_clk_resume, usage=1
[ 0.835487] DOUG: my_pm_clk_resume, usage=1
When I disabled serial console (speeding up boot), I got a different
pattern, which I guess (?) is better:
[ 0.089767] DOUG: my_pm_clk_resume, usage=1
[ 0.090507] DOUG: my_pm_clk_resume, usage=1
[ 0.151885] DOUG: my_pm_clk_suspend, usage=-2
[ 0.151914] DOUG: my_pm_clk_suspend, usage=-2
[ 1.825747] DOUG: my_pm_clk_resume, usage=-1
[ 1.825774] DOUG: my_pm_clk_resume, usage=-1
[ 1.888269] DOUG: my_pm_clk_suspend, usage=-2
[ 1.888282] DOUG: my_pm_clk_suspend, usage=-2
These different patterns have to do with the fact that the core PM
Runtime code really isn't designed to be robust to negative usage
counts and sometimes may happen to stumble upon a behavior that
happens to "work". For instance, you can see that
__pm_runtime_suspend() will treat any non-zero value (including
negative numbers) as if the device is in use.
In any case, let's fix the driver to be correct. We'll hold a
pm_runtime reference for the whole probe and then drop it (once!) at
the end. We'll get rid of manual pm_runtime_disable() calls in the
error handling. We'll also switch to devm_pm_runtime_enable(), which
magically handles undoing pm_runtime_use_autosuspend() as of commit
b4060db9251f ("PM: runtime: Have devm_pm_runtime_enable() handle
pm_runtime_dont_use_autosuspend()").
While we're at this, let's also use devm_pm_clk_create() instead of
rolling it ourselves.
Note that the above changes make it obvious that
lpassaudio_create_pm_clks() was doing more than just creating
clocks. It was also setting up pm_runtime parameters. Let's rename it.
All of these problems were found by code inspection. I started looking
at this driver because it was involved in a deadlock that I reported a
while ago [1]. Though I bisected the deadlock to commit 1b771839de05
("clk: qcom: gdsc: enable optional power domain support"), it was
never really clear why that patch affected it other than a luck of
timing changes. I'll also note that by fixing the timing (as done in
this change) we also seem to aboid the deadlock, which is a nice
benefit.
Also note that some of the fixes here are much the same type of stuff
that Dmitry did in commit 72cfc73f4663 ("clk: qcom: use
devm_pm_runtime_enable and devm_pm_clk_create"), but I guess
lpassaudiocc-sc7280.c didn't exist then.
[1] https://lore.kernel.org/r/20220922154354.2486595-1-dianders@chromium.org
Fixes: a9dd26639d05 ("clk: qcom: lpass: Add support for LPASS clock controller for SC7280")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221104064055.1.I00a0e4564a25489e85328ec41636497775627564@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da46ee19cbd8344d6860816b4827a7ce95764867 ]
If create_regulator() fails in set_supply(), the module refcount
needs be put to keep refcount balanced.
Fixes: e2c09ae7a74d ("regulator: core: Increase refcount for regulator supply's module")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221201122706.4055992-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5938196cc188ba4323bc6357f5ac55127d715888 ]
As comment of pci_get_device() says, it returns a pci_device with its
refcount increased. We need to call pci_dev_put() to decrease the
refcount. Save the return value of pci_get_device() and call
pci_dev_put() to decrease the refcount.
Fixes: 9093cfff72e3 ("mt76: mt7915: add support for using a secondary PCIe link for gen1")
Fixes: 2e30db0dde61 ("mt76: mt7915: add device id for mt7916")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dd0d49de7db680a856fa566963bb8421f46368 ]
Make sure the nss is valid for nss_delta array. Return zero
if the index is invalid.
Coverity message:
Event overrun-call: Overrunning callee's array of size 4 by passing
argument "n_chains" (which evaluates to 15) in call to
"mt76_tx_power_nss_delta".
int delta = mt76_tx_power_nss_delta(n_chains);
Fixes: 07cda406308b ("mt76: fix rounding issues on converting per-chain and combined txpower")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7eefb93d4a6fbccd859e538d208c50fd10b44cb7 ]
We should update CLC config before SAR set to synchronize all
related settings.
Fixes: 23bdc5d8cadf ("wifi: mt76: mt7921: introduce Country Location Control support")
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de147cc28985a2a09e5d6d179fc5ef59b22fc058 ]
mt7915 does not have a per-band number of chains unlike the other chips,
it only has a total number of chains. Yet the current code would
consider the total number as a per-band number.
For example, it would report that a 2x2 + 2x2 DBDC card have 4 chains on
each band and set chainmask to 0b1111 for the first interface and
0b11110000 for the second.
Fixes: 99ad32a4ca3a ("mt76: mt7915: add support for MT7986")
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7ec8bcf00034ce84d4c9a15dffd7577fbed4db2 ]
Rework tx paths and streams init part to improve readability, and make
sure that the available tx streams should be smaller than or equal to
the available tx paths.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Stable-dep-of: de147cc28985 ("wifi: mt76: mt7915: Fix chainmask calculation on mt7915 DBDC")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c881dc08fd71ca2673f31a64989fbb28eac26f4 ]
Correct mac timiing settings for different hardware generations.
This improves 40-60Mbps performance.
Fixes: 9aac2969fe5f ("mt76: mt7915: update mac timing settings")
Reported-By: Carson Vandegriffe <carson.vandegriffe@candelatech.com>
Tested-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c256ba6b1909f28b517274282b6845567e974143 ]
Group 3 in RxD is disabled in monitor mode. We should use the group 5 in
RxD instead to fix antenna signal way off issue, e.g we would see the
incorrect antenna signal value in wireshark. On the other hand, Group 5
wouldn't be used in STA or AP mode, so the patch shouldn't cause any
harm to those modes.
Fixes: cbaa0a404f8d ("mt76: mt7921: fix up the monitor mode")
Reported-by: Adrian Granados <agranados@gmail.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 833a9fd28c9b7ccb39a334721379e992dc1c0c89 ]
In regulatory_init_db(), when it's going to return a error, reg_pdev
should be unregistered. When load_builtin_regdb_keys() fails it doesn't
do it and makes cfg80211 can't be reload with report:
sysfs: cannot create duplicate filename '/devices/platform/regulatory.0'
...
<TASK>
dump_stack_lvl+0x79/0x9b
sysfs_warn_dup.cold+0x1c/0x29
sysfs_create_dir_ns+0x22d/0x290
kobject_add_internal+0x247/0x800
kobject_add+0x135/0x1b0
device_add+0x389/0x1be0
platform_device_add+0x28f/0x790
platform_device_register_full+0x376/0x4b0
regulatory_init+0x9a/0x4b2 [cfg80211]
cfg80211_init+0x84/0x113 [cfg80211]
...
Fixes: 90a53e4432b1 ("cfg80211: implement regdb signature checking")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Link: https://lore.kernel.org/r/20221109090237.214127-1-chenzhongjin@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09d838a457a89883a926b8b0104d575158fd4b92 ]
In ieee80211_lookup_key, the variable named `local` is unused if
compiled without lockdep, getting this warning:
net/mac80211/cfg.c: In function ‘ieee80211_lookup_key’:
net/mac80211/cfg.c:542:26: error: unused variable ‘local’ [-Werror=unused-variable]
struct ieee80211_local *local = sdata->local;
^~~~~
Fix it with __maybe_unused.
Fixes: 8cbf0c2ab6df ("wifi: mac80211: refactor some key code")
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Link: https://lore.kernel.org/r/20221111153622.29016-1-ihuguet@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cc58b376675981386c6192405fe887cd29c527a ]
As the nla_nest_start() may fail with NULL returned, the return value needs
to be checked.
Fixes: ce08cd344a00 ("wifi: nl80211: expose link information for interfaces")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221129014211.56558-1-yuancan@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7dbfa445ff7393d1c4c066c1727c9e0af1251958 ]
Commit f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 138c9c32f090
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Test case:
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/spi/spidev.h>
int main(int argc, char **argv)
{
char modew = SPI_CPHA;
char moder;
int f = open("/dev/spidev0.0", O_RDWR);
if (f < 0)
return 1;
ioctl(f, SPI_IOC_WR_MODE, &modew);
ioctl(f, SPI_IOC_RD_MODE, &moder);
return moder == modew ? 0 : 2;
}
Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5214f363dabca240446272dac54d404501ad5e5 ]
The "ignore_updelay" variable needs to be initialized to false.
Fixes: f8a65ab2f3ff ("bonding: fix link recovery in mode 2 when updelay is nonzero")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/Y4SWJlh3ohJ6EPTL@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9072931f020bfd907d6d89ee21ff1481cd78b407 ]
Use apply_bytes on ingress redirect, when apply_bytes is less than
the length of msg data, some data may be skipped and lost in
bpf_tcp_ingress().
If there is still data in the scatterlist that has not been consumed,
we cannot move the msg iter.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1669718441-2654-4-git-send-email-yangpc@wangsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a351d6087bf7d3d8440d58d3bf244ec64b89394a ]
When redirecting, we use sk_msg_to_ingress() to get the BPF_F_INGRESS
flag from the msg->flags. If apply_bytes is used and it is larger than
the current data being processed, sk_psock_msg_verdict() will not be
called when sendmsg() is called again. At this time, the msg->flags is 0,
and we lost the BPF_F_INGRESS flag.
So we need to save the BPF_F_INGRESS flag in sk_psock and use it when
redirection.
Fixes: 8934ce2fd081 ("bpf: sockmap redirect ingress support")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1669718441-2654-3-git-send-email-yangpc@wangsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a9841ca025275b5b0edfb0b618934abb6ceec15 ]
In tcp_bpf_send_verdict() redirection, the eval variable is assigned to
__SK_REDIRECT after the apply_bytes data is sent, if msg has more_data,
sock_put() will be called multiple times.
We should reset the eval variable to __SK_NONE every time more_data
starts.
This causes:
IPv4: Attempt to release TCP socket in state 1 00000000b4c925d7
------------[ cut here ]------------
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 5 PID: 4482 at lib/refcount.c:25 refcount_warn_saturate+0x7d/0x110
Modules linked in:
CPU: 5 PID: 4482 Comm: sockhash_bypass Kdump: loaded Not tainted 6.0.0 #1
Hardware name: Red Hat KVM, BIOS 1.11.0-2.el7 04/01/2014
Call Trace:
<TASK>
__tcp_transmit_skb+0xa1b/0xb90
? __alloc_skb+0x8c/0x1a0
? __kmalloc_node_track_caller+0x184/0x320
tcp_write_xmit+0x22a/0x1110
__tcp_push_pending_frames+0x32/0xf0
do_tcp_sendpages+0x62d/0x640
tcp_bpf_push+0xae/0x2c0
tcp_bpf_sendmsg_redir+0x260/0x410
? preempt_count_add+0x70/0xa0
tcp_bpf_send_verdict+0x386/0x4b0
tcp_bpf_sendmsg+0x21b/0x3b0
sock_sendmsg+0x58/0x70
__sys_sendto+0xfa/0x170
? xfd_validate_state+0x1d/0x80
? switch_fpu_return+0x59/0xe0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fixes: cd9733f5d75c ("tcp_bpf: Fix one concurrency problem in the tcp_bpf_send_verdict function")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/bpf/1669718441-2654-2-git-send-email-yangpc@wangsu.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2b80d9dd14cb5b70dc254bddbc4eea932694791 ]
The wistron_btns driver calls rtc_cmos_read(), which isn't
available with UML builds, so disable this driver on UML.
Prevents this build error:
ld: drivers/input/misc/wistron_btns.o: in function `poll_bios':
wistron_btns.c:(.text+0x4be): undefined reference to `rtc_cmos_read'
Fixes: 0bbadafdc49d ("um: allow disabling NO_IOMEM") # v5.14+
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20221130161604.1879-1-rdunlap@infradead.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d7cfb48d81353e826493d24c7cec7360950968f ]
icmp conntrack will set icmp redirects as RELATED, but icmpv6 will not
do this.
For icmpv6, only icmp errors (code <= 128) are examined for RELATED state.
ICMPV6 Redirects are part of neighbour discovery mechanism, those are
handled by marking a selected subset (e.g. neighbour solicitations) as
UNTRACKED, but not REDIRECT -- they will thus be flagged as INVALID.
Add minimal support for REDIRECTs. No parsing of neighbour options is
added for simplicity, so this will only check that we have the embeeded
original header (ND_OPT_REDIRECT_HDR), and then attempt to do a flow
lookup for this tuple.
Also extend the existing test case to cover redirects.
Fixes: 9fb9cbb1082d ("[NETFILTER]: Add nf_conntrack subsystem.")
Reported-by: Eric Garver <eric@garver.life>
Link: https://github.com/firewalld/firewalld/issues/1046
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Garver <eric@garver.life>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55226f8553d255f5002c751c7c6ba9291f34bf2 ]
@pll->rate_table has allocated memory by kmemdup(), if clk_hw_register()
fails, it should be freed, otherwise it will cause memory leak issue,
this patch fixes it.
Fixes: b4cbe606dc36 ("clk: visconti: Add support common clock driver and reset driver")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Link: https://lore.kernel.org/r/20221122152353.204132-1-xiujianfeng@huawei.com
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97b801be6f8e53676b9f2b105f54e35c745c1b22 ]
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context. We fix it by going to
err_pm instead of err_clk.
Fixes:f086ba9d5389c ("ASoC: pcm512x: Support mastering BCLK/LRCLK using the PLL")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220928160402.126140-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1382901f75a5a7dc8eac05059fd0c7816def4eae ]
When (size != 0 || ptrs->lvds_ entries != 3), the program tries to
free() the ptrs. However, the ptrs is not created by calling kzmalloc(),
but is obtained by pointer offset operation.
This may lead to memory leaks or undefined behavior.
Fix this by replacing the arguments of kfree() with ptrs_block.
Fixes: a87d0a847607 ("drm/i915/bios: Generate LFP data table pointers if the VBT lacks them")
Signed-off-by: Xia Fukun <xiafukun@huawei.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125063428.69486-1-xiafukun@huawei.com
(cherry picked from commit 7674cd0b7d28b952151c3df26bbfa7e07eb2b4ec)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75818afff631e1ea785a82c3e8bb82eb0dee539c ]
This patch fixes potential memory leakage and seg fault
in _gpuvm_import_dmabuf() function
Fixes: d4ec4bdc0bd5 ("drm/amdkfd: Allow access for mmapping KFD BOs")
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca54639c7752edf1304d92ff4d0c049d4efc9ba0 ]
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in amdgpu_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 725a521a18734f65de05b8d353b5bd0d3ca4c37a ]
As comment of pci_get_class() says, it returns a pci_device with its
refcount increased and decreased the refcount for the input parameter
@from if it is not NULL.
If we break the loop in radeon_atrm_get_bios() with 'pdev' not NULL, we
need to call pci_dev_put() to decrease the refcount. Add the missing
pci_dev_put() to avoid refcount leak.
Fixes: d8ade3526b2a ("drm/radeon: handle non-VGA class pci devices with ATRM")
Fixes: c61e2775873f ("drm/radeon: split ATRM support out from the ATPX handler (v3)")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6dca7efe6e522bf213c7dab691fa580d82f48f74 ]
Return true early if ASIC is in BACO state already, no need
to talk to SMU. It can fix the issue that driver was not
calling BACO exit at all in runtime pm resume, and a timing
issue leading to a PCI AER error happened eventually.
Fixes: 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a46315295489933209e902638cd287aeb5f982ab ]
It seems like CLK_INFRA_ADC_FRC_CK always need to be enabled for
CLK_INFRA_ADC_26M_CK to work. Instead of adding this dependency to the
mtk-thermal and mt6577_auxadc drivers, add dependency to the clock
driver clk-mt7986-infracfg.c.
Fixes: ec97d23c8e22 ("clk: mediatek: add mt7986 clock support")
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/5e55012567da74870e1fb2edc2dc513b5821e523.1666801017.git.daniel@makrotopia.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cbb264d4e9136acab2c8fd39e39ab1b1402b84b ]
If the device does not come straight from reset, we might receive an IRQ
before we are ready to handle it.
Fixes:
[ 2.334737] Unable to handle kernel read from unreadable memory at virtual address 00000000000001e4
[ 2.522601] Call trace:
[ 2.525040] regmap_read+0x1c/0x80
[ 2.528434] mt8173_afe_irq_handler+0x40/0xf0
...
[ 2.598921] start_kernel+0x338/0x42c
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Fixes: ee0bcaff109f ("ASoC: mediatek: Add AFE platform driver")
Link: https://lore.kernel.org/r/20221128-mt8173-afe-v1-0-70728221628f@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7927afb5e27baac694f585b59c436ba323528dc2 ]
Commit a8b5aef2cca1 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width")
introduced a line where the pointer returned by ieee80211_find_sta() is
used after rcu_read_unlock().
Move rcu_read_unlock() a bit lower to fix this.
Fixes: a8b5aef2cca1 ("wifi: rtl8xxxu: gen2: Enable 40 MHz channel width")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/3c82ad09-7593-3be1-1d2c-e58505fb43cb@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 895b3b06efc285c1245242e9638b9ae251dc13ec ]
urbs does not be freed in exception paths in __lf_x_usb_enable_rx().
That will trigger memory leak. To fix it, add kfree() for urbs within
"error" label. Compile tested only.
Fixes: 68d57a07bfe5 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221119051900.1192401-1-william.xuanziyang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9d86515c3d4c0564a0c31a2df87d735353a1971e ]
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release().
Fixes: 3285ea10e9b0 ("ALSA: asihpi - Interrelated HPI tidy up.")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Link: https://lore.kernel.org/r/20221126021429.3029562-1-liushixin2@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35e3b6ae84935d0d7ff76cbdaa83411b0ad5e471 ]
When mounting from a NFSv4 referral, path->dentry can end up being a
negative dentry, so derive the struct nfs_server from the dentry
itself instead.
Fixes: 2b0143b5c986 ("VFS: normal filesystems (and lustre): d_inode() annotations")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 51069e4aef6257b0454057359faed0ab0c9af083 ]
If we're asked to recover open state while a delegation return is
outstanding, then the state manager thread cannot use a cached open, so
if the server returns a delegation, we can end up deadlocked behind the
pending delegreturn.
To avoid this problem, let's just ask the server not to give us a
delegation unless we're explicitly reclaiming one.
Fixes: be36e185bd26 ("NFSv4: nfs4_open_recover_helper() must set share access")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
