IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
RK3588 has three USB3 controllers. This adds the host-only controller,
which is using the naneng-combphy shared with PCIe and SATA.
The other two are dual-role and using a different PHY that is not yet
supported upstream.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20231020150022.48725-4-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Rockchip RK3588 one of the DWC3 cores is integrated weirdly and
requires two extra clocks to be enabled. Without these extra clocks
hot-plugging USB devices is broken.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231020150022.48725-3-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RK3588 has three DWC3 controllers. Two of them are fully functional in
host, device and OTG mode including USB2 support. They are connected to
dedicated PHYs, that also support USB-C's DisplayPort alternate mode.
The third controller is connected to one of the combphy's shared
with PCIe and SATA. It can only be used in host mode and does not
support USB2. Compared to the other controllers this one needs
some extra clocks.
While adding the extra clocks required by RK3588, I noticed grf_clk
is not available on RK3568, so I disallowed it for that platform.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231020150022.48725-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a reset-controller for supporting Xilinx versal platforms. To reset
the USB controller, get the reset ID from device-tree and using ID trigger
the reset, with the assert and deassert reset controller APIs for USB
controller initialization.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20231013125847.20334-1-piyush.mehta@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
The function mtu3_remove() can only return a non-zero value if
ssusb->dr_mode is neiter USB_DR_MODE_PERIPHERAL nor USB_DR_MODE_HOST nor
USB_DR_MODE_OTG. In this case however the probe callback doesn't succeed
and so the remove callback isn't called at all. So the code branch
resulting in this error path could just be dropped were it not for the
compiler choking on "enumeration value 'USB_DR_MODE_UNKNOWN' not handled
in switch [-Werror=switch]". So instead replace this code path by a
WARN_ON and then mtu3_remove() be converted to return void trivially.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231020151537.2202675-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver for the NXP PTN36502 Type-C USB 3.1 Gen 1 and DisplayPort
v1.2 combo redriver.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231020-ptn36502-v2-2-b37a337d463e@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document bindings for this Type-C USB 3.1 Gen 1 and DisplayPort v1.2
combo redriver.
The PTN36502 can also run in GPIO mode where it is configured
differently, without any I2C connection, but this is not supported yet.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20231020-ptn36502-v2-1-b37a337d463e@fairphone.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
module_platform_driver_probe() has the advantage that the .probe() and
.remove() calls can live in .init.text and .exit.text respectively and
so some memory is saved. The downside is that dynamic bind and unbind
are impossible. As the driver doesn't benefit from the advantages (both
.probe and .remove are defined in plain .text), stop suffering from the
downsides and use module_platform_driver() instead of
module_platform_driver_probe().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231017204442.1625925-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 14485de431 ("usb: Use device_get_match_data()") dropped the
unconditional use of ci_hdrc_usb2_of_match resulting in this warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:41:34: warning: unused variable 'ci_hdrc_usb2_of_match' [-Wunused-const-variable]
The fix is to drop of_match_ptr() which is not necessary because DT is
always used for this driver.
Fixes: 14485de431 ("usb: Use device_get_match_data()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310131627.M43j234A-lkp@intel.com/
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231019183015.841460-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add Nuvoton NPCM BMC SoCs support to USB ChipIdea driver.
NPCM SoC includes ChipIdea IP block that is used for USB device controller
mode.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231017195903.1665260-4-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding CI_HDRC_FORCE_VBUS_ACTIVE_ALWAYS flag to modify the vbus_active
parameter to active in case the ChipIdea USB IP role is device-only and
there is no otgsc register.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20231017195903.1665260-2-tmaimon77@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "reset-gpios" is optional in real case, for example reset pin is
is hard wired to "high". And this fact is also reflected by the
devm_gpio_get_optional() calling in driver code.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231018150448.1980-1-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch internal usb-storage quirk value to 64-bit as quirks currently
use all 32 bits.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231016072604.40179-3-gmazyland@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes macro that was used only by commit that was reverted
in commit ab4b71644a ("USB: storage: fix Huawei mode switching
regression")
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231016072604.40179-2-gmazyland@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a 120ms delay implemented for allowing the XHCI host controller to
detect a U3 wakeup pulse. The intention is to wait for the device to retry
the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status
by the time it is checked. As per the USB3 specification:
tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts")
This would allow the XHCI resume sequence to determine if the root hub
needs to be also resumed. However, in case there is no device connected,
or if there is only a HSUSB device connected, this delay would still affect
the overall resume timing.
Since this delay is solely for detecting U3 wake events (USB3 specific)
then ignore this delay for the disconnected case and the HSUSB connected
only case.
[skip helper function, rename usb3_connected variable -Mathias ]
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this driver enables the xHC clocks while resuming from sleep, it calls
clk_prepare_enable() without checking for errors and blithely goes on to
read/write the xHC's registers -- which, with the xHC not being clocked,
at least on ARM32 usually causes an imprecise external abort exceptions
which cause kernel oops. Currently, the chips for which the driver does
the clock dance on suspend/resume seem to be the Broadcom STB SoCs, based
on ARM32 CPUs, as it seems...
Found by Linux Verification Center (linuxtesting.org) with the Svace static
analysis tool.
Fixes: 8bd954c561 ("usb: host: xhci-plat: suspend and resume clocks")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some situations where xhci removal happens parallel to xhci_handshake,
we encounter a scenario where the xhci_handshake can't succeed, and it
polls until timeout.
If xhci_handshake runs until timeout it can on some platforms result in
a long wait which might lead to a watchdog timeout.
Add a helper that checks xhci status during the handshake, and exits if
set state is entered. Use this helper in places where xhci_handshake is
called unlocked and has a long timeout. For example xhci command timeout
and xhci reset.
[commit message and code comment rewording -Mathias]
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current function that both removes and frees an interrupter isn't
optimal when using several interrupters. The array of interrupters need
to be protected with a lock while removing interrupters, but the default
xhci spin lock can't be used while freeing the interrupters event ring
segment table as dma_free_coherent() should be called with IRQs enabled.
There is no need to free the interrupter under the lock, so split this
code into separate unlocked free part, and a lock protected remove part.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD USB host controller (1022:43f7) isn't going into PCI D3 by default
without anything connected. This is because the policy that was introduced
by commit a611bf473d ("xhci-pci: Set runtime PM as default policy on all
xHC 1.2 or later devices") only covered 1.2 or later.
The 1.1 specification also has the same requirement as the 1.2
specification for D3 support. So expand the runtime PM as default policy
to all AMD 1.1 devices as well.
Fixes: a611bf473d ("xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices")
Link: https://composter.com.ua/documents/xHCI_Specification_for_USB.pdf
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the event ring dequeue pointer for port change events in the
same way as other event types. No need to handle it separately.
This only touches the driver side tracking of event ring dequeue.
Note: this does move forward the event ring dequeue increase for port
change events a bit.
Previously the dequeue was increased before temporarily dropping
the xhci lock while kicking roothub polling.
Now dequeue is increased after re-aquiring the lock.
This should not matter as event ring dequeue is not touched at all by
hub thread. It's only touched in xhci interrupt handler.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No matter what type of event we receive we want to increase the event
ring dequeue pointer one step for every event that is handled.
For unknown reasons the event ring dequeue increase is done inside the
transfer event handler and port event handler.
As the transfer event handler got more complex and can now loop through
several transfer TRBs on a transfer ring, there were additinal checks
added to avoid increasing event ring dequeue more than one step.
No need for elaborate checks to avoid increasing event ring dequeue
in case the transfer event handler goes through a loop.
Just increasing the event ring dequeue outside the transfer event
handler.
End goal is to increase event ring dequeue in just one place.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_alloc_erst() has global scope even though it's only used in
xhci-mem.c. Declare it static.
xhci_free_erst() was removed by commit b17a57f89f ("xhci: Refactor
interrupter code for initial multi interrupter support."), but a
declaration in xhci.h still remains. Drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ebd88cf507 ("xhci: Remove unused defines for ERST_SIZE and
ERST_ENTRIES") removed the ERST_SIZE macro but retained a code comment
explaining the quantity chosen in the macro.
Remove the code comment as well.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias notes that the ERST_PTR_MASK macro is named as if it's masking
the Event Ring Dequeue Pointer in the ERDP register, but in actuality
it's masking the inverse.
Invert the macro's value for clarity.
Migrate it to the modern GENMASK_ULL() syntax to avoid u64 casts.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ring segments have just been amended with a monotonically increasing
number.
To allow developers to inspect the segment numbers and ensure
correctness in particular after ring expansion, expose them in each
ring's "trbs" file in debugfs.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When expanding a ring at its "end", ring->last_seg needs to be updated
for Event Rings as well, not just for all the other ring types.
This is not a fix because ring expansion currently isn't done on the
Event Ring. It's just in preparation for when it's added.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initial xhci_ring allocation has just been amended to assign a
monotonically increasing number to each ring segment.
However rings may be expanded after initial allocation.
So number newly inserted segments starting from the preceding segment in
the ring and renumber all segments succeeding the newly inserted ones.
This is not a fix because ring expansion currently isn't done on the
Event Ring and that's the only ring type using the segment number.
It's just in preparation for when either Event Ring expansion is added
or when other ring types start making use of the segment number.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
Event Ring is drained by the kernel.
Commit dc0ffbea57 ("usb: host: xhci: update event ring dequeue pointer
on purpose") mitigated the issue by advancing the Event Ring Dequeue
Pointer already after half a segment has been processed. Nevertheless,
providing a larger Event Ring would be useful to cope with load peaks.
Expand the number of event TRB slots available by increasing the number
of Event Ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, but with up to 32k it can be excessively high
(sec 5.3.4). So cap the actual number at 2 (configurable through the
ERST_MAX_SEGS macro), which seems like a reasonable quantity. It is
supported by any xHC because the limit in the HCSPARAMS2 register is
defined as a power of 2. Renesas uPD720201 and VIA VL805 controllers
do not support more than 2 ERST entries.
An alternative to increasing the number of Event Ring segments would be
an increase of the segment size. But that requires allocating multiple
contiguous pages, which may be impossible if memory is fragmented.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using more than one Event Ring segment (ERSTSZ > 1), software shall
set the DESI bits in the ERDP register to the number of the segment to
which the upper ERDP bits are pointing. The xHC may use the DESI bits
as a shortcut to determine whether it needs to check for an Event Ring
Full condition: If it's enqueueing events in a different segment, it
need not compare its internal Enqueue Pointer with the Dequeue Pointer
in the upper bits of the ERDP register (sec 5.5.2.3.3).
Not setting the DESI bits correctly can result in the xHC enqueueing
events past the Dequeue Pointer. On Renesas uPD720201 host controllers,
incorrect DESI bits cause an interrupt storm. For comparison, VIA VL805
host controllers do not exhibit such problems. Perhaps they do not take
advantage of the optimization afforded by the DESI bits.
To fix the issue, assign the segment number to each struct xhci_segment
in xhci_segment_alloc(). When advancing the Dequeue Pointer in
xhci_update_erst_dequeue(), write the segment number to the DESI bits.
On driver probe, set the DESI bits to zero in xhci_set_hc_event_deq() as
processing starts in segment 0. Likewise on driver teardown, clear the
DESI bits to zero in xhci_free_interrupter() when clearing the upper
bits of the ERDP register. Previously those functions (incorrectly)
treated the DESI bits as if they're declared RsvdP.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The next_trb() helper relies on a link TRB at the end of a ring segment
to know a segment ends. This works well with transfer rings that use
link trbs, but not with event rings.
Event rings segments are always filled by host to segment size
before moving to next segment. It does not use link TRBs
Check for both link trb and full segment in next_trb() helper to
support event rings.
Useful if several interrupters with several event rings are supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With several xhci controllers active at the same time its hard to
keep track of ports without knowing bus number
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to trace other port structure members than just port number
so pass entire port structure as parameter instead of just port number.
Dig the port number from the port structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a i.MX8QXP MEK board that has an NXP CBDTU02043 mux, there is
no mode-switch support, only orientation switch.
Make the 'mode-switch' property a non-required one.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231016131141.680517-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Type-C port drivers can make PM related decisions based
on is the device USB3 or USB2.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding functions that USB hub code can use to inform the
Type-C class about connected USB devices.
Once taken into use, it will allow the Type-C port drivers
to power off components that are not needed, for example if
USB2 device is enumerated, everything that is only relevant
for USB3 (retimers, etc.), can be powered off.
This will also create a symlink "typec" for the USB devices
pointing to the USB Type-C partner device.
Suggested-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231011105825.320062-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 45e34c8af5, and the
two subsequent fixes to it:
3f874c9b2a ("x86/smp: Don't send INIT to non-present and non-booted CPUs")
b1472a60a5 ("x86/smp: Don't send INIT to boot CPU")
because it seems to result in hung machines at shutdown. Particularly
some Dell machines, but Thomas says
"The rest seems to be Lenovo and Sony with Alderlake/Raptorlake CPUs -
at least that's what I could figure out from the various bug reports.
I don't know which CPUs the DELL machines have, so I can't say it's a
pattern.
I agree with the revert for now"
Ashok Raj chimes in:
"There was a report (probably this same one), and it turns out it was a
bug in the BIOS SMI handler.
The client BIOS's were waiting for the lowest APICID to be the SMI
rendevous master. If this is MeteorLake, the BSP wasn't the one with
the lowest APIC and it triped here.
The BIOS change is also being pushed to others for assimilation :)
Server BIOS's had this correctly for a while now"
and it does look likely to be some bad interaction between SMI and the
non-BSP cores having put into INIT (and thus unresponsive until reset).
Link: https://bbs.archlinux.org/viewtopic.php?pid=2124429
Link: https://www.reddit.com/r/openSUSE/comments/16qq99b/tumbleweed_shutdown_did_not_finish_completely/
Link: https://forum.artixlinux.org/index.php/topic,5997.0.html
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2241279
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 295525e29a ("virtio_net: merge dma operations when filling
mergeable buffers") unmaps the buffer with DMA_ATTR_SKIP_CPU_SYNC when
the dma->ref is zero. We do that with DMA_ATTR_SKIP_CPU_SYNC, because we
do not want to do the sync for the entire page_frag. But that misses the
sync for the current area.
This patch does cpu sync regardless of whether the ref is zero or not.
Fixes: 295525e29a ("virtio_net: merge dma operations when filling mergeable buffers")
Reported-by: Michael Roth <michael.roth@amd.com>
Closes: http://lore.kernel.org/all/20230926130451.axgodaa6tvwqs3ut@amd.com
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve a
number of small reported issues. Included in here are:
- thunderbolt driver fixes
- xhci driver fixes
- cdns3 driver fixes
- musb driver fixes
- a number of typec driver fixes
- a few other small driver fixes
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZSwElQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylx7ACgthY1JVY+YL61s2CBKgSdVJ7eAJUAnjnFwSy4
KTcgnEAnFlm/xpfVgHwA
=2xN2
-----END PGP SIGNATURE-----
Merge tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt fixes from Greg KH:
"Here are some USB and Thunderbolt driver fixes for 6.6-rc6 to resolve
a number of small reported issues. Included in here are:
- thunderbolt driver fixes
- xhci driver fixes
- cdns3 driver fixes
- musb driver fixes
- a number of typec driver fixes
- a few other small driver fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-6.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (22 commits)
usb: typec: ucsi: Use GET_CAPABILITY attributes data to set power supply scope
usb: typec: ucsi: Fix missing link removal
usb: typec: altmodes/displayport: Signal hpd low when exiting mode
xhci: Preserve RsvdP bits in ERSTBA register correctly
xhci: Clear EHB bit only at end of interrupt handler
xhci: track port suspend state correctly in unsuccessful resume cases
usb: xhci: xhci-ring: Use sysdev for mapping bounce buffer
usb: typec: ucsi: Clear EVENT_PENDING bit if ucsi_send_command fails
usb: misc: onboard_hub: add support for Microchip USB2412 USB 2.0 hub
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: cdns3: Modify the return value of cdns_set_active () to void when CONFIG_PM_SLEEP is disabled
usb: dwc3: Soft reset phy on probe for host
usb: hub: Guard against accesses to uninitialized BOS descriptors
usb: typec: qcom: Update the logic of regulator enable and disable
usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call
usb: musb: Get the musb_qh poniter after musb_giveback
usb: musb: Modify the "HWVers" register address
usb: cdnsp: Fixes issue with dequeuing not queued requests
thunderbolt: Restart XDomain discovery handshake after failure
thunderbolt: Correct TMU mode initialization from hardware
...
