IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 7dd12fe34686d89c332b1a05104d18d728591f0a ]
Before this change, when operating in polled mode, i.e. no IRQ is
available, every individual C45 access would be hit with a 150us sleep
after the bus access.
For example, on a board with a CN9130 SoC connected to an MV88X3310
PHY, a single C45 read would take around 165us:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 165ms
By replacing the long sleep with a tighter poll loop, we observe a 10x
increase in bus throughput:
root@infix:~$ mdio f212a600.mdio-mii mmd 4:1 bench 0xc003
Performed 1000 reads in 15ms
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20231204100811.2708884-3-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 867046cc7027703f60a46339ffde91a1970f2901 upstream.
Allow (for example) min(unsigned_var, 20).
The opposite min(signed_var, 20u) is still errored.
Since a comparison between signed and unsigned never makes the unsigned
value negative it is only necessary to adjust the __types_ok() test.
Link: https://lkml.kernel.org/r/633b64e2f39e46bb8234809c5595b8c7@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4ead534fba42fc4fd41163297528d2aa731cd121 upstream.
Since 'unsigned char/short' get promoted to 'signed int' it is safe to
compare them against an 'int' value.
Link: https://lkml.kernel.org/r/8732ef5f809c47c28a7be47c938b28d4@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4b84b2ff851f01d0fac619eadef47eb41648534 upstream.
Remove the extra indentation and align continuation markers.
Link: https://lkml.kernel.org/r/bed41317a05c498ea0209eafbcab45a5@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d03eba99f5bf7cbc6e2fdde3b6fa36954ad58e09 upstream.
The type-check in min()/max() is there to stop unexpected results if a
negative value gets converted to a large unsigned value. However it also
rejects 'unsigned int' v 'unsigned long' compares which are common and
never problematc.
Replace the 'same type' check with a 'same signedness' check.
The new test isn't itself a compile time error, so use static_assert() to
report the error and give a meaningful error message.
Due to the way builtin_choose_expr() works detecting the error in the
'non-constant' side (where static_assert() can be used) also detects
errors when the arguments are constant.
Link: https://lkml.kernel.org/r/fe7e6c542e094bfca655abcd323c1c98@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 80fcac55385ccb710d33a20dc1caaef29bd5a921 upstream.
Patch series "minmax: Relax type checks in min() and max()", v4.
The min() (etc) functions in minmax.h require that the arguments have
exactly the same types.
However when the type check fails, rather than look at the types and fix
the type of a variable/constant, everyone seems to jump on min_t(). In
reality min_t() ought to be rare - when something unusual is being done,
not normality.
The orginal min() (added in 2.4.9) replaced several inline functions and
included the type - so matched the implicit casting of the function call.
This was renamed min_t() in 2.4.10 and the current min() added. There is
no actual indication that the conversion of negatve values to large
unsigned values has ever been an actual problem.
A quick grep shows 5734 min() and 4597 min_t(). Having the casts on
almost half of the calls shows that something is clearly wrong.
If the wrong type is picked (and it is far too easy to pick the type of
the result instead of the larger input) then significant bits can get
discarded.
Pretty much the worst example is in the derived clamp_val(), consider:
unsigned char x = 200u;
y = clamp_val(x, 10u, 300u);
I also suspect that many of the min_t(u16, ...) are actually wrong. For
example copy_data() in printk_ringbuffer.c contains:
data_size = min_t(u16, buf_size, len);
Here buf_size is 'unsigned int' and len 'u16', pass a 64k buffer (can you
prove that doesn't happen?) and no data is returned. Apparantly it did -
and has since been fixed.
The only reason that most of the min_t() are 'fine' is that pretty much
all the values in the kernel are between 0 and INT_MAX.
Patch 1 adds umin(), this uses integer promotions to convert both
arguments to 'unsigned long long'. It can be used to compare a signed
type that is known to contain a non-negative value with an unsigned type.
The compiler typically optimises it all away. Added first so that it can
be referred to in patch 2.
Patch 2 replaces the 'same type' check with a 'same signedness' one. This
makes min(unsigned_int_var, sizeof()) be ok. The error message is also
improved and will contain the expanded form of both arguments (useful for
seeing how constants are defined).
Patch 3 just fixes some whitespace.
Patch 4 allows comparisons of 'unsigned char' and 'unsigned short' to
signed types. The integer promotion rules convert them both to 'signed
int' prior to the comparison so they can never cause a negative value be
converted to a large positive one.
Patch 5 (rewritted for v4) allows comparisons of unsigned values against
non-negative constant integer expressions. This makes
min(unsigned_int_var, 4) be ok.
The only common case that is still errored is the comparison of signed
values against unsigned constant integer expressions below __INT_MAX__.
Typcally min(int_val, sizeof (foo)), the real fix for this is casting the
constant: min(int_var, (int)sizeof (foo)).
With all the patches applied pretty much all the min_t() could be replaced
by min(), and most of the rest by umin(). However they all need careful
inspection due to code like:
sz = min_t(unsigned char, sz - 1, LIM - 1) + 1;
which converts 0 to LIM.
This patch (of 6):
umin() and umax() can be used when min()/max() errors a signed v unsigned
compare when the signed value is known to be non-negative.
Unlike min_t(some_unsigned_type, a, b) umin() will never mask off high
bits if an inappropriate type is selected.
The '+ 0u + 0ul + 0ull' may look strange.
The '+ 0u' is needed for 'signed int' on 64bit systems.
The '+ 0ul' is needed for 'signed long' on 32bit systems.
The '+ 0ull' is needed for 'signed long long'.
Link: https://lkml.kernel.org/r/b97faef60ad24922b530241c5d7c933c@AcuMS.aculab.com
Link: https://lkml.kernel.org/r/41d93ca827a248698ec64bf57e0c05a5@AcuMS.aculab.com
Signed-off-by: David Laight <david.laight@aculab.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6e9d38f8eb00ac8b52e6d15f6aa9bcecacb081b upstream.
BUILD_BUG_ON*() macros are defined in build_bug.h. Include it. Replace
compiler_types.h by compiler.h, which provides the former, to have a
definition of the __UNIQUE_ID().
Link: https://lkml.kernel.org/r/20230912092355.79280-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
commit 5e57418a2031cd5e1863efdf3d7447a16a368172 upstream.
It appears that compiler_types.h already have an implementation of the
__unconst_integer_typeof() called __unqual_scalar_typeof(). Use it
instead of the copy.
Link: https://lkml.kernel.org/r/20230911154913.4176033-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53122a49f49796beb2c4a1bb702303b66347e29f ]
We should set the status to FC_TIMED_OUT when a timeout error is passed to
fc_fcp_rec_error().
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231129165832.224100-3-hare@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b57c4db5d23b9df0118a25e2441c9288edd73710 ]
The current FC error recovery is sending up to three REC (recovery) frames
in 10 second intervals, and as a final step sending an ABTS after 30
seconds for the command itself. Unfortunately sending an ABTS is also the
action for the SCSI abort handler, and the default timeout for SCSI
commands is also 30 seconds. This causes two ABTS to be scheduled, with the
libfc one slightly earlier. The ABTS scheduled by SCSI EH then sees the
command to be already aborted, and will always return with a 'GOOD' status
irrespective on the actual result from the first ABTS. This causes the
SCSI EH abort handler to always succeed, and SCSI EH never to be engaged.
Fix this by not issuing an ABTS when a SCSI command is present for the
exchange, but rather wait for the abort scheduled from SCSI EH. And warn
if an abort is already scheduled to avoid similar errors in the future.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231129165832.224100-2-hare@kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed7e818a7b501012038d6bc6fedadaf7375a380a ]
For AP mode, the peer is created earlier in ath12k_mac_op_add_interface() but
ath12k_mac_op_assign_vif_chanctx() will try to create peer again. Then an
error will return which makes AP mode startup fail.
Kernel log:
[ 5017.665006] ath12k_pci 0000:04:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant log:
Failed to set beacon parameters
Interface initialization failed
wls1: interface state UNINITIALIZED->DISABLED
wls1: AP-DISABLED
wls1: Unable to setup interface.
Failed to initialize AP interface
wls1: interface state DISABLED->DISABLED
wls1: AP-DISABLED
So fix this check and enable AP mode for WCN7850, as now AP mode works normally.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121022459.17209-1-quic_kangyang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 79d93b3c6ffd79abcd8e43345980aa1e904879c4 ]
Both map deletion operation, map release and map free operation use
fd_array_map_delete_elem() to remove the element from fd array and
need_defer is always true in fd_array_map_delete_elem(). For the map
deletion operation and map release operation, need_defer=true is
necessary, because the bpf program, which accesses the element in fd
array, may still alive. However for map free operation, it is certain
that the bpf program which owns the fd array has already been exited, so
setting need_defer as false is appropriate for map free operation.
So fix it by adding need_defer parameter to bpf_fd_array_map_clear() and
adding a new helper __fd_array_map_delete_elem() to handle the map
deletion, map release and map free operations correspondingly.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Link: https://lore.kernel.org/r/20231204140425.1480317-4-houtao@huaweicloud.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 756b31203d482d2dd1aa6c208978b0410dc7530f ]
In concurrent mode, when STA interface is scanning, it causes
AP interface TX beacon on wrong channel. We modified it to scan
with the operating channel when one of the interfaces is already
connected. Additionally, STA interface need to stop scan when AP
interface is starting to avoid TX beacon on wrong channel. Finally,
AP interface need to stop TX beacon when STA interface is scanning
and switching to non-OP channel,This prevent other device to get
beacons on wrong channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231129070046.18443-5-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5082b3e3027eae393a4e86874bffb4ce3f83c26e ]
We are seeing below error randomly in the case where only
one MSI vector is configured:
kernel: ath11k_pci 0000:03:00.0: wmi command 16387 timeout
The reason is, currently, in ath11k_pcic_ext_irq_enable(),
ATH11K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
This results in a race condition: after
ATH11K_FLAG_EXT_IRQ_ENABLED is set but before NAPI enabled,
CE interrupt breaks in. Since IRQ is shared by CE and data
path, ath11k_pcic_ext_interrupt_handler() is also called
where we call disable_irq_nosync() to disable IRQ. Then
napi_schedule() is called but it does nothing because NAPI
is not enabled at that time, meaning
ath11k_pcic_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Finally
we get above error.
Fix it by setting ATH11K_FLAG_EXT_IRQ_ENABLED after all
NAPI and IRQ work are done. With the fix, we are sure that
by the time ATH11K_FLAG_EXT_IRQ_ENABLED is set, NAPI is
enabled.
Note that the fix above also introduce some side effects:
if ath11k_pcic_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH11K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231117003919.26218-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2adc886244dff60f948497b59affb6c6ebb3c348 ]
Fix an array-index-out-of-bounds read in ath9k_htc_txstatus(). The bug
occurs when txs->cnt, data from a URB provided by a USB device, is
bigger than the size of the array txs->txstatus, which is
HTC_MAX_TX_STATUS. WARN_ON() already checks it, but there is no bug
handling code after the check. Make the function return if that is the
case.
Found by a modified version of syzkaller.
UBSAN: array-index-out-of-bounds in htc_drv_txrx.c
index 13 is out of range for type '__wmi_event_txstatus [12]'
Call Trace:
ath9k_htc_txstatus
ath9k_wmi_event_tasklet
tasklet_action_common
__do_softirq
irq_exit_rxu
sysvec_apic_timer_interrupt
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231113065756.1491991-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b16904fd9f01b580db357ef2b1cc9e86d89576c2 ]
With latest upstream llvm18, the following test cases failed:
$ ./test_progs -j
#13/2 bpf_cookie/multi_kprobe_link_api:FAIL
#13/3 bpf_cookie/multi_kprobe_attach_api:FAIL
#13 bpf_cookie:FAIL
#77 fentry_fexit:FAIL
#78/1 fentry_test/fentry:FAIL
#78 fentry_test:FAIL
#82/1 fexit_test/fexit:FAIL
#82 fexit_test:FAIL
#112/1 kprobe_multi_test/skel_api:FAIL
#112/2 kprobe_multi_test/link_api_addrs:FAIL
[...]
#112 kprobe_multi_test:FAIL
#356/17 test_global_funcs/global_func17:FAIL
#356 test_global_funcs:FAIL
Further analysis shows llvm upstream patch [1] is responsible for the above
failures. For example, for function bpf_fentry_test7() in net/bpf/test_run.c,
without [1], the asm code is:
0000000000000400 <bpf_fentry_test7>:
400: f3 0f 1e fa endbr64
404: e8 00 00 00 00 callq 0x409 <bpf_fentry_test7+0x9>
409: 48 89 f8 movq %rdi, %rax
40c: c3 retq
40d: 0f 1f 00 nopl (%rax)
... and with [1], the asm code is:
0000000000005d20 <bpf_fentry_test7.specialized.1>:
5d20: e8 00 00 00 00 callq 0x5d25 <bpf_fentry_test7.specialized.1+0x5>
5d25: c3 retq
... and <bpf_fentry_test7.specialized.1> is called instead of <bpf_fentry_test7>
and this caused test failures for #13/#77 etc. except #356.
For test case #356/17, with [1] (progs/test_global_func17.c)), the main prog
looks like:
0000000000000000 <global_func17>:
0: b4 00 00 00 2a 00 00 00 w0 = 0x2a
1: 95 00 00 00 00 00 00 00 exit
... which passed verification while the test itself expects a verification
failure.
Let us add 'barrier_var' style asm code in both places to prevent function
specialization which caused selftests failure.
[1] https://github.com/llvm/llvm-project/pull/72903
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20231127050342.1945270-1-yonghong.song@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f55da4cc37051cda600ea870ce8cf29f1297715 ]
imx7d-lcdif is compatible to imx6sx-lcdif. MXSFB_V6 supports overlay
by using LCDC_AS_CTRL register. This registers used by overlay plane:
* LCDC_AS_CTRL
* LCDC_AS_BUF
* LCDC_AS_NEXT_BUF
are listed in i.MX7D RM as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d4ac04fa7c3f6dc263dba6f575a2ec7a2d4eca8 ]
imx7d uses two ports for 'in-ports', so the syntax port@<num> has to
be used. imx7d has both port and port@1 nodes present, raising these
error:
funnel@30041000: in-ports: More than one condition true in oneOf schema
funnel@30041000: Unevaluated properties are not allowed
('in-ports' was unexpected)
Fix this by also using port@0 for imx7s as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c9260ff28ee561fca5f96425c9328a9698e8427b ]
Add PCI IDs checks for the cases where SAS5116 diverges from SAS4116 in
behavior.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Link: https://lore.kernel.org/r/20231123160132.4155-3-sumit.saxena@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2689b6a86b9d23574bd4b654bf770b6034e2c7e ]
The device is always reset two consecutive times (ax88179_reset is called
twice), one from usbnet_probe during the device binding and the other from
usbnet_open.
Remove the non-necessary reset during the device binding and let the reset
operation from open to keep the normal behavior (tested with generic ASIX
Electronics Corp. AX88179 Gigabit Ethernet device).
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120121239.54504-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d6b83f1e3707c4d60acfa58afd3515e17e5d5384 ]
If failed to allocate "tags" or could not find the final upper device from
start_dev's upper list in bond_verify_device_path(), only the loopback
detection of the current upper device should be affected, and the system is
no need to be panic.
So return -ENOMEM in alb_upper_dev_walk to stop walking, print some warn
information when failed to allocate memory for vlan tags in
bond_verify_device_path.
I also think that the following function calls
netdev_walk_all_upper_dev_rcu
---->>>alb_upper_dev_walk
---------->>>bond_verify_device_path
From this way, "end device" can eventually be obtained from "start device"
in bond_verify_device_path, IS_ERR(tags) could be instead of
IS_ERR_OR_NULL(tags) in alb_upper_dev_walk.
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20231118081653.1481260-1-shaozhengchao@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ed48c80b28d8dcd584d6ddaf00c75b7673e1a05 ]
Spectrum-{1,2,3,4} devices report that a D3hot->D0 transition causes a
reset (i.e., they advertise NoSoftRst-). However, this transition does
not have any effect on the device: It continues to be operational and
network ports remain up. Advertising this support makes it seem as if a
PM reset is viable for these devices. Mark it as unavailable to skip it
when testing reset methods.
Before:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
pm bus
After:
# cat /sys/bus/pci/devices/0000\:03\:00.0/reset_method
bus
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 915d25a9d69be969c1cc6c1dd0c3861f6da7b55e ]
In case of no phc we should not return SOFTWARE TIMESTAMPING flags as we do
not know whether the netdev supports of timestamping.
Remove it from the lan8841_ts_info and simply return 0.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 07e6a553c2f1d385edfc9185081dee442a9dd38d ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@fa600000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@fa600000: missing or empty reg/ranges property
Subtract 0xfa600000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ba2a45a48503665f7e8eeec51f8b40456566b0cd ]
The camera node has both unit address and children within the same bus
mapping, thus needs proper ranges property to fix dtc W=1 warnings:
Warning (unit_address_vs_reg): /soc/camera@11800000: node has a unit name, but no reg or ranges property
Warning (simple_bus_reg): /soc/camera@11800000: missing or empty reg/ranges property
Subtract 0x11800000 from all its children nodes. No functional impact
expected.
Link: https://lore.kernel.org/r/20230722121719.150094-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f5779b529240b715f0e358489ad0ed933bf77c97 ]
Because file_name and phba->ModelName are both declared a size 80 bytes,
the extra ".grp" file extension could cause an overflow into file_name.
Define a ELX_FW_NAME_SIZE macro with value 84. 84 incorporates the 4 extra
characters from ".grp". file_name is changed to be declared as a char and
initialized to zeros i.e. null chars.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20231031191224.150862-3-justintee8345@gmail.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c6724abf969251af53cdae525ad8100ec78d3c2 ]
Xen broadcasts SGI to each VM when multiple VMs run on Xen hypervisor. In
such case spurious SGI is expected if one event is registered by one VM and
not registered by another VM. We let users know that Unhandled SGI is not
error and expected if kernel is running on Xen hypervisor.
Signed-off-by: Tanmay Shah <tanmay.shah@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1698431039-2734260-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daed80ed07580e5adc0e6d8bc79933a35154135a ]
When preemption is enabled in kernel and if any task which can be
preempted should not use smp_processor_id() directly, since CPU
switch can happen at any time, the previous value of cpu_id
differs with current cpu_id. As a result we see the below call trace
during xlnx_event_manager_probe.
[ 6.140197] dump_backtrace+0x0/0x190
[ 6.143884] show_stack+0x18/0x40
[ 6.147220] dump_stack_lvl+0x7c/0xa0
[ 6.150907] dump_stack+0x18/0x34
[ 6.154241] check_preemption_disabled+0x124/0x134
[ 6.159068] debug_smp_processor_id+0x20/0x2c
[ 6.163453] xlnx_event_manager_probe+0x48/0x250
To protect cpu_id, It is recommended to use get_cpu()/put_cpu()
to disable preemption, get the cpu_id and enable preemption respectively.
(For Reference, Documentation/locking/preempt-locking.rst and
Documentation/kernel-hacking/hacking.rst)
Use preempt_disable()/smp_processor_id()/preempt_enable()
API's to achieve the same.
Signed-off-by: HariBabu Gattem <haribabu.gattem@xilinx.com>
Signed-off-by: Jay Buddhabhatti <jay.buddhabhatti@amd.com>
Link: https://lore.kernel.org/r/20231027055622.21544-1-jay.buddhabhatti@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 455a4c46e023ab84263eae0fc7acca9a5ee8b7ac ]
As the vendor DTS files were moved to per-vendor subdirs, there no need
to use common prefixes. Drop the `qcom-' prefix from PMIC dtsi file.
This makes 32-bit qcom/ dts files closer to arm64 ones.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230928110309.1212221-8-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4849775587844e44d215289c425bcd70f315efe7 ]
If the net_cls subsystem is already mounted, attempting to mount it again
in setup_classid_environment() will result in a failure with the error code
EBUSY. Despite this, tmpfs will have been successfully mounted at
/sys/fs/cgroup/net_cls. Consequently, the /sys/fs/cgroup/net_cls directory
will be empty, causing subsequent setup operations to fail.
Here's an error log excerpt illustrating the issue when net_cls has already
been mounted at /sys/fs/cgroup/net_cls prior to running
setup_classid_environment():
- Before that change
$ tools/testing/selftests/bpf/test_progs --name=cgroup_v1v2
test_cgroup_v1v2:PASS:server_fd 0 nsec
test_cgroup_v1v2:PASS:client_fd 0 nsec
test_cgroup_v1v2:PASS:cgroup_fd 0 nsec
test_cgroup_v1v2:PASS:server_fd 0 nsec
run_test:PASS:skel_open 0 nsec
run_test:PASS:prog_attach 0 nsec
test_cgroup_v1v2:PASS:cgroup-v2-only 0 nsec
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup.procs
(cgroup_helpers.c:540: errno: No such file or directory) Opening cgroup classid: /sys/fs/cgroup/net_cls/cgroup-test-work-dir/net_cls.classid
run_test:PASS:skel_open 0 nsec
run_test:PASS:prog_attach 0 nsec
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup-test-work-dir/cgroup.procs
run_test:FAIL:join_classid unexpected error: 1 (errno 2)
test_cgroup_v1v2:FAIL:cgroup-v1v2 unexpected error: -1 (errno 2)
(cgroup_helpers.c:248: errno: No such file or directory) Opening Cgroup Procs: /sys/fs/cgroup/net_cls/cgroup.procs
#44 cgroup_v1v2:FAIL
Summary: 0/0 PASSED, 0 SKIPPED, 1 FAILED
- After that change
$ tools/testing/selftests/bpf/test_progs --name=cgroup_v1v2
#44 cgroup_v1v2:OK
Summary: 1/0 PASSED, 0 SKIPPED, 0 FAILED
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Link: https://lore.kernel.org/r/20231111090034.4248-3-laoar.shao@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50da74e1e8b682853d1e07fc8bbe3a0774ae5e09 ]
Refer to Mediatek vendor driver RxDCOC_Calibration() function, when
performing gainfreeze calibration, we should write register 140
instead of 141. This fix can reduce the total calibration time from
6 seconds to 1 second.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315B13B89DF57B6B27BB854BCAFA@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 100888fb6d8a185866b1520031ee7e3182b173de ]
With latest clang18 (main branch of llvm-project repo), when building bpf selftests,
[~/work/bpf-next (master)]$ make -C tools/testing/selftests/bpf LLVM=1 -j
The following compilation error happens:
fatal error: error in backend: Branch target out of insn range
...
Stack dump:
0. Program arguments: clang -g -Wall -Werror -D__TARGET_ARCH_x86 -mlittle-endian
-I/home/yhs/work/bpf-next/tools/testing/selftests/bpf/tools/include
-I/home/yhs/work/bpf-next/tools/testing/selftests/bpf -I/home/yhs/work/bpf-next/tools/include/uapi
-I/home/yhs/work/bpf-next/tools/testing/selftests/usr/include -idirafter
/home/yhs/work/llvm-project/llvm/build.18/install/lib/clang/18/include -idirafter /usr/local/include
-idirafter /usr/include -Wno-compare-distinct-pointer-types -DENABLE_ATOMICS_TESTS -O2 --target=bpf
-c progs/pyperf180.c -mcpu=v3 -o /home/yhs/work/bpf-next/tools/testing/selftests/bpf/pyperf180.bpf.o
1. <eof> parser at end of file
2. Code generation
...
The compilation failure only happens to cpu=v2 and cpu=v3. cpu=v4 is okay
since cpu=v4 supports 32-bit branch target offset.
The above failure is due to upstream llvm patch [1] where some inlining behavior
are changed in clang18.
To workaround the issue, previously all 180 loop iterations are fully unrolled.
The bpf macro __BPF_CPU_VERSION__ (implemented in clang18 recently) is used to avoid
unrolling changes if cpu=v4. If __BPF_CPU_VERSION__ is not available and the
compiler is clang18, the unrollng amount is unconditionally reduced.
[1] 1a2e77cf9e
Signed-off-by: Yonghong Song <yonghong.song@linux.dev>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Link: https://lore.kernel.org/bpf/20231110193644.3130906-1-yonghong.song@linux.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4c7e887324f5776eef6e6e47a90e0ac8058a7a8 ]
Some compilers complain about get_pprint_mapv_size() not returning value
in some code paths. Fix with explicit return.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231102033759.2541186-3-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2b62aa59d02ed281fa4fc218df3ca91b773e1e62 ]
Compiler complains about malloc(). We also don't need to dynamically
allocate anything, so make the life easier by using statically sized
buffer.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/r/20231102033759.2541186-2-andrii@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a11d965a218f0cd95b13fe44d0bcd8a20ce134a8 ]
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031530EB6D98DCE4DF20766CBCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e416514e309f7e25e577fee45a65f246f67b2261 ]
Since 'rtw89_core_tx_kick_off_and_wait()' assumes timeout
(actually RTW89_ROC_TX_TIMEOUT) in milliseconds, I suppose
that RTW89_ROC_IDLE_TIMEOUT is in milliseconds as well. If
so, 'msecs_to_jiffies()' should be used in a call to
'ieee80211_queue_delayed_work()' from 'rtw89_roc_end()'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231024143137.30393-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d1935ac02ca5aee364a449a35e2977ea84509b0 ]
When we online resize an ext4 filesystem with a oversized flexbg_size,
mkfs.ext4 -F -G 67108864 $dev -b 4096 100M
mount $dev $dir
resize2fs $dev 16G
the following WARN_ON is triggered:
==================================================================
WARNING: CPU: 0 PID: 427 at mm/page_alloc.c:4402 __alloc_pages+0x411/0x550
Modules linked in: sg(E)
CPU: 0 PID: 427 Comm: resize2fs Tainted: G E 6.6.0-rc5+ #314
RIP: 0010:__alloc_pages+0x411/0x550
Call Trace:
<TASK>
__kmalloc_large_node+0xa2/0x200
__kmalloc+0x16e/0x290
ext4_resize_fs+0x481/0xd80
__ext4_ioctl+0x1616/0x1d90
ext4_ioctl+0x12/0x20
__x64_sys_ioctl+0xf0/0x150
do_syscall_64+0x3b/0x90
==================================================================
This is because flexbg_size is too large and the size of the new_group_data
array to be allocated exceeds MAX_ORDER. Currently, the minimum value of
MAX_ORDER is 8, the minimum value of PAGE_SIZE is 4096, the corresponding
maximum number of groups that can be allocated is:
(PAGE_SIZE << MAX_ORDER) / sizeof(struct ext4_new_group_data) ≈ 21845
And the value that is down-aligned to the power of 2 is 16384. Therefore,
this value is defined as MAX_RESIZE_BG, and the number of groups added
each time does not exceed this value during resizing, and is added multiple
times to complete the online resizing. The difference is that the metadata
in a flex_bg may be more dispersed.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231023013057.2117948-4-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b099eb87de105cf07cad731ded6fb40b2675108b ]
In commit 967ac8af4475 ("ext4: fix potential integer overflow in
alloc_flex_gd()"), an overflow check is added to alloc_flex_gd() to
prevent the allocated memory from being smaller than expected due to
the overflow. However, after kmalloc() is replaced with kmalloc_array()
in commit 6da2ec56059c ("treewide: kmalloc() -> kmalloc_array()"), the
kmalloc_array() function has an overflow check, so the above problem
will not occur. Therefore, the extra check is removed.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231023013057.2117948-3-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 658a52344fb139f9531e7543a6e0015b630feb38 ]
The maximum value of flexbg_size is 2^31, but the maximum value of int
is (2^31 - 1), so overflow may occur when the type of flexbg_size is
declared as int.
For example, when uninit_mask is initialized in ext4_alloc_group_tables(),
if flexbg_size == 2^31, the initialized uninit_mask is incorrect, and this
may causes set_flexbg_block_bitmap() to trigger a BUG_ON().
Therefore, the flexbg_size type is declared as unsigned int to avoid
overflow and memory waste.
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231023013057.2117948-2-libaokun1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68da4c44b994aea797eb9821acb3a4a36015293e ]
Suppose we issue two FITRIM ioctls for ranges [0,15] and [16,31] with
mininum length of trimmed range set to 8 blocks. If we have say a range of
blocks 10-22 free, this range will not be trimmed because it straddles the
boundary of the two FITRIM ranges and neither part is big enough. This is a
bit surprising to some users that call FITRIM on smaller ranges of blocks
to limit impact on the system. Also XFS trims all free space extents that
overlap with the specified range so we are inconsistent among filesystems.
Let's change ext4_try_to_trim_range() to consider for trimming the whole
free space extent that straddles the end of specified range, not just the
part of it within the range.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20231216010919.1995851-1-yebin10@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>
