IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Remove comment about adding start delay since it will
be done when support for A/V synchronization is added.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add the I2C device node for the rt5647 codec.
Eventually, this will be done automatically somewhere
else but for now its done in the audio driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The asoc_simple_dai structure does not contain the 'fmt'
member in Linux kernel version v4.1 and later so only
build code that uses it when the kernel version is earlier
than v4.1.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Set the various DAI formats so the bridge on the module
is the master of all clocks and the codec is the slave.
The only DAI protocol currently supported is I2S.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Instead of using the fixed suffix, '6-001b', in the
codec name, generate it from the I2S adapter number
and I2C address of the codec.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The greybus code requires that an operation's response buffer be
the exact size of the response; however, the size of the response to
the GB_I2S_MGMT_TYPE_GET_SUPPORTED_CONFIGURATIONS operation is unknown.
To fix this, an extension to the I2S specification is required.
In the meantime, set the number of configurations returned to 20
because that is how many configurations will be returned (using
"insider knowledge" of the firmware).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
The rt5647 codec on speaker and mediabar modules require that
the following clock edge settings:
ll_wclk_change_edge GB_I2S_MGMT_EDGE_FALLING
ll_wclk_tx_edge GB_I2S_MGMT_EDGE_RISING
ll_wclk_rx_edge GB_I2S_MGMT_EDGE_FALLING
(Those are the setting that work, at least). So make the Greybus
audio driver configure the GPBridge with those settings.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix section mismatches introduced by b27227ce93c0 ("greybus: Use
gb_gpbridge_protocol_init()"), which added __exit annotation to
gpbridge-protocol exit functions that are called in the error path of
gpbridge_init, which lives in the init section.
This triggered the following modpost warning:
WARNING: modpost: Found 8 section mismatch(es).
Fixes: 16b33d100bff ("protocol: Add gb_gpbridge_protocol_driver()")
Fixes: b27227ce93c0 ("greybus: Use gb_gpbridge_protocol_init()")
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Increase the maximum allowed buffer size to the full 16-bit range
supported by the protocol.
Note that host devices will generally use smaller buffers than the
maximum.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Host devices impose buffer-size constraints on Greybus core which are
taken into account when allocating messages.
Make sure to verify these constraints when the host device is allocated,
rather than when the first message is allocated.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove a couple of unused function prototypes from the greybus header
file.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Remove unnecessary greybus.h include from header files.
Signed-off-by: Johan Hovold <johan@hovoldconsulting.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There are many gpbridge protocol drivers that need gb_protocol_driver()
without the module_init/exit() lines. Lets create one for them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
That's what followed for .h, etc.. Rename for better consistency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This is what coding guidelines say. Lets do it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Routines should be named this way: gb_<object>_<operation>. Fix all
routines that don't match this.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In order to facilitate re-use of spi structures, split them out of
independent files and add them into a shared gpbridge.h
This will be a prereq to sharing these headers w/ gbsim.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Spaces were present in place of tab. Fix that.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This is what I get over mainline:
greybus/raw.c: In function 'gb_raw_send':
greybus/raw.c:153:2: error: implicit declaration of function 'copy_from_user' [-Werror=implicit-function-declaration]
if (copy_from_user(&request->data[0], data, len)) {
^
greybus/raw.c: In function 'raw_read':
greybus/raw.c:305:2: error: implicit declaration of function 'copy_to_user' [-Werror=implicit-function-declaration]
if (copy_to_user(buf, &raw_data->data[0], raw_data->len)) {
^
Fix this by including uaccess.h.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
This adds a driver that implements the greybus Raw protocol as
specified.
It preserves the message boundries by only allowing a read to receive
a "full" message, and any write() call also is passed in a single
greybus request.
Totally untested, given that we have no raw firmware or gbsim code yet.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
ida_simple_* has a built-in spinlock, no need to grab another lock when
accessing it.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
All we need is a simple ida, so use that interface instead of the more
"complex" idr one. Bonus is we don't need to fix the locking issue I
forgot about when using an idr, as ida has one built-in.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
It should remove the object from sysfs when loopback
connection init error.
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add checks for options that shall be enabled in the kernel config
and for options that shall be disable.
To add options to list append them to CONFIG_OPTIONS_ENABLE or
CONFIG_OPTIONS_DISABLE respectively.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
There's no reason we can't support loopback pings or transfers
initiated by the module. Allow it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Add some symbols to indicate what kind of "function" the
loopback thread is supposed to be performing--the type of
traffic it generates over its connection.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Use a symbolic constant to define the maximum time (number of
milliseconds) to delay between initiated operations.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Fix a comment that incorrectly says the delay between messages is
limited to 1024 msec; it actually must be <= 1000 msec.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
If an error occurs starting up the loopback thread, the error code
is not extracted properly. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In gb_loopback_check_attr(), the value of gb->type is checked for
validity. The only valid values are 0, 1, and 2. But the check
allows the value 3. Fix that.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
sparse is rightfully complaining about a lack of converting when
accessing or assigning to little endian fields. Fix them all up to work
properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
This makes some functions and structures static, as warned by sparse, as
they don't need to be global.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Alex Elder <elder@linaro.org>
remane protocol define from GREYBUS_PROTOCOL_LED to GREYBUS_PROTOCOL_LIGHTS to
be coherent with the specification.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
We already have code to parse Endo ID, lets use it to create modules at
run time instead of creating them from a static array.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Endo is described by a 16 bit value. Which represents the properties of
modules, interface and ribs on front and back of endo.
This 16 bit value can be used to find all possible pairs of modules and
interfaces and creating modules based on that.
This patch provides helpers to parse 16 bit Endo ID.
(Based on original code written by Alex Elder.)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
In commit 1efb53a220b7 ("ASoC: simple-card: Remove support for setting
differing DAI formats"), the .fmt field was removed from struct
asoc_simple_dai. Fix this build breakage by not trying to set it.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
sizeof wants %zu when on a 64bit build, so change the dev_err() call to
remove a build warning in the audio.c file.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Introduce INSTALL_MOD_PATH to allow for building and installing of the
greybus modules from a different location.
This lets you build the greybus modules on a PC and then install the
modules to an SD card in the appropriate location relative to the SD such
as /media/sdcard/lib/modules/version and subsequent running of depmod in
the same location. If INSTALL_MOD_PATH isn't specified the default
behaviour of installing and depmoding to /lib/modules/version is
maintained.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
So here's the current greybus audio driver, which I
wanted to send out for more serious review and
consideration for merging.
I've tried to integrate much of the feedback from the
last round and most of the hotplug issues that I've found
have been resolved. I've tested this via gbsim, and the
Android ARA HAL layer seems to work with it.
Mark has also successfully played audio with this driver,
adding a few hacks to get the codec's i2c connection to
probe.
Current issues:
* Hotplug problem - When gbsim is killed, or the module
removed, the greybus driver gets stuck since the android
mediaserver process is holding the audio device open.
Killing the mediaserver allows things to clean up and
allows greybus to accept new gbsim connections. I have
a workaround patch to the soc-core.c logic which converts
the snd_card_free() call to snd_card_free_when_closed()
which allows the greybus connection cleanup to finish.
Remaining todos:
* Probably need to break apart the mgmt_setup function
to integrate better with the constraint logic. I took
a really basic stab at this, but more is probably
needed.
* Figure out how to properly find and tie in the
codec's I2C bus-id to the driver.
This code requires that the kernel support the following
config options, which I've enabled in a separate kernel
patch:
CONFIG_SND_SIMPLE_CARD
CONFIG_SND_SOC_SPDIF
CONFIG_SND_SOC_RT5645
I really can't calim to be the sole author of this, since
many many fixes and tweaks that have been folded in have
come from Mark Greer. His analsysis and debugging is really
what has made this dummy-framework driver evolve into an
actual audio driver. So much credit and thanks to Mark!
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
All protocols use the same value to distinguish between request and
response message types. This is a requirement.
Use GB_MESSAGE_TYPE_RESPONSE rather than GB_OPERATION_TYPE_RESPONSE
for the name of the flag used to distiguish between request and
response messages.
Get rid of the redundant response flag definitions that are
associated with specific protocols.
Describe the symbolic values as "operation types" rather than
"message types" where they are defined. The message type for a
request is the same as the operation type; the message type for a
response is the operation type OR'd with GB_MESSAGE_TYPE_RESPONSE.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Conditionally define a new symbol DRIVER_OWNS_PSY_STRUCT, which is
set in "kernel_ver.h" based on on the kernel version. Use it to
distinguish code used for kernels that differ in whether a power
supply structure is owned by the driver, or by the power supply
core.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
When a battery connection is initialized, a gb_battery structure for
it is allocated in gb_battery_connection_init(). Currently that
function ends by calling init_and_register(); in the event an error
occurs, init_and_register() is responsible for freeing the allocated
gb_battery structure.
Make the code a bit better balanced by having the function that
allocates the structure be responsible for freeing it in case of
error.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Both ES1 and ES2 drivers cannot be loaded due to a driver name conflict.
Give ES2 driver the correct name.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
No need to go past 80 characters for the define_get_version macro, so
fix up the indentation to not do so.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Remove the trailing ';' character from the gb_protocol_driver() macro as
it's not needed and is bad coding style.
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
