IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
MT7996 hardware supports mesh A-MSDU subframes in hardware, but uses a
big-endian length field
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230314095956.62085-7-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This helps bring down rx CPU usage by avoiding calls to the rx handlers in
the slow path. Supports forwarding and local rx, including A-MSDU.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230314095956.62085-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Significantly reduces mesh forwarding path CPU usage and enables the
direct use of iTXQ.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/20230314095956.62085-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, fast xmit only worked on interface types where initially a
sta lookup is performed, and a cached header can be attached to the sta,
requiring only some fields to be updated at runtime.
This technique is not directly applicable for a mesh device type due
to the dynamic nature of the topology and protocol. There are more
addresses that need to be filled, and there is an extra header with a
dynamic length based on the addressing mode.
Change the code to cache entries contain a copy of the mesh subframe header +
bridge tunnel header, as well as an embedded struct ieee80211_fast_tx, which
contains the information for building the 802.11 header.
Add a mesh specific early fast xmit call, which looks up a cached entry and
adds only the mesh subframe header, before passing it over to the generic
fast xmit code.
To ensure the changes in network are reflected in these cached headers,
flush affected cached entries on path changes, as well as other conditions
that currently trigger a fast xmit check in other modes (key changes etc.)
This code is loosely based on a previous implementation by:
Sriram R <quic_srirrama@quicinc.com>
Cc: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230314095956.62085-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the sequence number is shared across different tx queues, it needs
to be atomic in order to avoid accidental duplicate assignment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230314095956.62085-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On newer MediaTek SoCs (e.g. MT7986), WLAN->WLAN or WLAN->Ethernet flows can
be offloaded by the SoC. In order to support that, the .ndo_setup_tc op is
needed.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230321091248.30947-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of enabling HW timestamping by default every time a station
is connected, disable it by default and enable it only upon request
for a specific station. HW timestamping can be enabled for only one
peer at a time.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.62b98fbf545b.I450c1017ada7900a71a63d879bb542a08e3166c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we have a new MLD STA cmd, there will be a different function to
add/remove a station in MLD mode. But both functions will share a
common part. Put this part in a separate function which will be used
later in adding/removing a sta in MLD mode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.d01e0c9ccdc3.I5e9e27c3b363b36209a0ff960d2e59708e7ff0bf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In iwl_mvm_add_sta() we're initializing the new allocated mvm_sta.
We are setting some fields to zero even though it was allocated with
kzalloc, for the case of HW restart. But in such a case we will never
get to this initializations due to the goto statement that we have in
this case. Remove these initializations.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.c0b4d1e986a5.I6959bf1aca74c865e3c1edbf711f5fe8fb8c0c9f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a new STA cmd as part of the new MLD API. There are some
parts of sending the STA cmd which are common to both the old and
the new one. Put this parts in functions which will later be used
to send the new STA cmd.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.4da940bd7384.I3a66990fbffe9611b5e41f3686c2aff37ba2eb56@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the new MLD API is introduced, we have a new enumeration
for the different station types. Since struct iwl_mvm_sta's
sta_type field will be in use for both new and old API,
change its type to a unified one, so it can hold both.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.c8b86d8ddd3e.I9581235860b91654b4f6c3a8797c777702690998@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function sends the STA_HE_CTXT_CMD, which won't be used in the
new MLD API. Instead, a part of the fields of this command
will be in the new STA cmd. Put the parts that are common to both
commands in functions, which will later be used in sending the new
STA cmd.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.19b9b6c346ab.I0b8512eb64d8f03ff83879bafe9707f897d5b3c6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We used to send a MAC CTXT cmd to ask the FW to not pass MCAST frames
if we're associated but not authorized, because we don't have the
keys in that stage, and after authorization - we sent the cmd again
to ask the FW to pass MCAST, as we have the keys now.
The patch linked below was changing this strategy to always allow
MCAST frames, and if we're not authorized - the driver will drop them.
But we're still sending the MAC CTXT cmd after deaouthorization even
though we don't tell the FW to not pass MCAST frames anymore.
Basically we don't tell the FW anything new with this cmd.
Fix this by not sending MAC CTXT command after deauthorization.
For authorization we're sending the cmd to configure other changes too,
so keep it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.11b3481bc497.I9672acff9cfc00e7e1a187e7178caa3a1911a1b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callbacks added here use the new MLD FW API
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.42b0d4726b8d.I0755baace47c0ab1d9d70137448125d3140ef3af@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callbacks added here use the new MLD FW API
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.3eb485c359fc.I28be198ea9389083d5a01f68c92763722613ba9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_get_sync_time() reads the gp2 from the device and then
reads the system clock. Since the two reads are not done atomically,
unexpected delays may happen between the two reads (e.g. context
switch) which make it inaccurate.
In order to improve the accuracy of the cross timestamp, call
iwl_mvm_get_sync_time() multiple times in a loop and take the
result in which the difference between the two clock is the smallest.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.d9e6f8f8998a.I569939ec4ddf0c6c64c112e7d0c30583f5509d9a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement the following PHC operations:
1. adjtime - for adding an offset to the PHC clock time.
2. adjfine - for adjusting the PHC clock frequency.
3. gettime64 - for getting the PHC clock time. This function returns
the time as adjusted by adjtime and adjfine.
The adjusted time will also be used for time sync frames timestamping.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.f59750deeee4.I110a7e3ac3c6d39d9dbe1fe77001e3f5bc3814eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For TM/FTM frames, report the hardware timestamps reported by the
fw as part of the RX/TX status. Since the fw reports the timestamps
in a dedicated notification (and not as part of the RX/TX status),
hold the frame until the fw timestamps notification is received.
Timestamping is enabled when a station is connected and disabled
when disconnected. For AP interface, only the first station will
have timestamping enabled since the fw only supports timestamping
for one peer.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.e0392d498101.I9bf12c8ecfb3f17253a13dc48a48647ddd6e7855@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware supports reading synced GP2/ATRB timestamps,
read the synced timestamps from firmware instead of reading the
GP2 register and the system time separately. Reading the synced
time from firmware should be more accurate.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.a6be5f0b5580.Idedb496a5943fa496143066ffbed08185a8c4582@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to enable/disable PHC clock. The PHC clock includes support
for fetching the cross timestamp i.e. a non-atomic snapshot of the current
time from the hardware (WiFi device) clock and system clock (wall-clock)
simultaneously.
Signed-off-by: Krishnanand Prabhu <krishnanand.prabhu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.ae1d64f513b9.Ib3b6ad61c9fa2fc5908f1e0d6f59f4af6eec1a77@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This chip is found in cheap "free driver" USB adapters from Aliexpress.
Initially they pretend to be a CD-ROM containing the driver for Windows.
"Ejecting" switches the device to wifi mode.
Features: 2.4 GHz, b/g/n mode, 1T1R, 150 Mbps.
This chip is more unique than other Realtek chips:
* The registers at addresses 0x0-0xff, which all the other chips use,
can't be used here. New registers at 0x8000-0x80ff must be used
instead. And it's not a simple matter of adding 0x8000: 0x2
(REG_SYS_FUNC) became 0x8004, 0x80 (REG_MCU_FW_DL) became 0x8090,
etc.
* Also there are a few new registers which must be accessed indirectly
because their addresses don't fit in 16 bits. No other chips seem to
have these.
* The vendor driver compiles to 8188gu.ko, but the code calls the chip
RTL8710B(U) pretty much everywhere, including messages visible to the
user.
Another difference compared to the other chips supported by rtl8xxxu is
that it has a new PHY status struct, or three of them actually, from
which we extract the RSSI, among other things. This is not unique,
though, just new. The chips supported by rtw88 also use it.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/4edbe29f-00b9-8eef-9789-20bed0b141e2@gmail.com
Always run the entire init sequence (rtl8xxxu_init_device()) for
RTL8192EU. It's what the vendor driver does too.
This fixes a bug where the device is unable to connect after
rebooting:
wlp3s0f3u2: send auth to ... (try 1/3)
wlp3s0f3u2: send auth to ... (try 2/3)
wlp3s0f3u2: send auth to ... (try 3/3)
wlp3s0f3u2: authentication with ... timed out
Rebooting leaves the device powered on (partially? at least the
firmware is still running), but not really in a working state.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Jes Sorensen <jes@trained-monkey.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/4eb111a9-d4c4-37d0-b376-4e202de7153c@gmail.com
Clang errors:
drivers/net/wireless/intel/iwlwifi/iwl-devtrace.c:15:32: error: unknown warning group '-Wsuggest-attribute=format', ignored [-Werror,-Wunknown-warning-option]
#pragma GCC diagnostic ignored "-Wsuggest-attribute=format"
^
1 error generated.
The warning being disabled by this pragma is GCC specific. Guard its use
with CONFIG_CC_IS_GCC so that it is not used with clang to clear up the
error.
Fixes: 4eca8cbf7ba8 ("wifi: iwlwifi: suppress printf warnings in tracing")
Link: https://github.com/ClangBuiltLinux/linux/issues/1818
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230315-iwlwifi-fix-pragma-v1-1-ad23f92c4739@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can't really be fixed due to the macro layout of
tracepoints (you'd need a special tracepoint macro for
when this is needed), so just suppress the warnings.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of issues here:
* if trans->reduce_power_loaded is already true, we call
iwl_trans_set_reduce_power() with an uninitialized len
value
* in this case we also clobber a previous load/setting
* if iwl_uefi_get_reduced_power() returns an ERR_PTR() we
try to kfree() it
Move the iwl_trans_set_reduce_power() call into the success
case only to fix these issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.aa2cf2281f5d.I33b4ab3427f1921c184c52fecd0f46781a89dc8a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there's a rate->index that maps inside the range but
to an uninitialized value, then that's also a bad rate,
avoid printing "(nil)" in that case and rather print the
"BAD_RATE" string instead as in the else branch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.06b38d160fc5.I45a9254d3658b1ce796aa4c427193d3cbf638d7e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cppcheck reports
[drivers/net/wireless/intel/iwlwifi/mvm/rs.c:2686]: (warning) Assignment of function parameter has no effect outside the function. Did you forget dereferencing it?
The setting of the 'sta' parameter is not needed. In the if-check that sets it
to NULL, mvm_sta is also set to NULL. Then the next statement checks if
mvm_sta is NULL and does an early return. So remove setting sta.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.711fe28cfdd6.I2f723f9d44f65720baaf3e84b72109759350a8f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callback added here uses the new MLD FW API
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.5d4bcd384425.I263eef3aad8efe23a597843fe7c56924038c8fdc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.fa05929badb9.I2222dc86cf7d7a7bb58c6a2f2529c8089bfe58b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another patch in the series adding all the ops
for the new MLD ieee80211_ops.
The callback added here uses the new MLD FW API.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.d3753975e720.I45f89cc81370d2cf8d4f51748ccb3ec675eff1bd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since parts of the functionality of this function is going to be used
also by the MLD version of it, put in a separate function the parts
that are common for both MLD and non-MLD modes.
The common function will later be used in the MLD ops.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.844755701cac.I1c650718ad2381eabc38f4103c1aac67936a1ffc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD remove_interface() callback
which uses the new MLD APIs.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.b87c5c0a4b6b.I631173a73d6ffd7232aa539ea8b356a222fac398@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD add_interface() callback
which uses the new MLD APIs added the previous patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.6adc29bff39b.I97ed469028009be9392dcc6f7b5ffbe45f4b2c43@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have new commands for STA
related operations (add/remove/aux/disable tx).
Add structures and enum definitions, along with part of the functions
that sends this commands.
This functions will be in used and more will be added in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.132873ce015c.I7b12a77e5be066730762e6ceeeaa7190293c3df1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have a new LINK command
to add/remove/configure a link.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
These functions will be in used in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.d7808329effb.I13bea2db206b78540bc866bc3ab755ad5be78c53@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As a part of the new MLD FW API changes, we have a new MAC CTXT command.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
This functions will be in used in the next patches.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.99a41a5bc55f.I310312c829f5f2f69b64fcddce487b1eab80165b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor MAC_CONTEXT_CMD sending flow:
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The MAC_CONTEXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. Use iwl_mvm_mac_ctxt_send_cmd when removing a mac instead of
implementing the same functionality once again.
3. Change the debug print when sending the command to be more specific,
so it will be easy to distinguish later if the old or new mac command
was sent.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.3ab62700db4e.I2e353b308667c215aa456c160e0d90de2b9b85cc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor STA_HE_CTXT_CMD sending flow:
1. As the new MLD API is introduced, there are some common fields in
both the old and new APIs. The STA_HE_CTXT_CMD of the non-MLD API
has common fields with the link and mac commands of the new MLD API.
Put this common parts in functions so it can be used later by the
new MLD API.
2. The HE capability which indicates whether the NIC is ack-enabled or
not is the same for all bands. No need to take it from the specific
band which is currently in use. Take it from the low band - this
simplifies the code and doesn't require a phy_ctxt.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.7ca960596953.Ifc3e816461abbd69c6fd87752342afcedfebc293@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In FW restart scenarios, we allocate the queues from the
iwl_mvm_realloc_queues_after_restart() function, but that
is called before we insert the station ID into our map
(mvm->fw_id_to_mac_id).
However, in all cases where we're actually allocating a
queue for a "real" (not bcast, aux, ...) station we have
the sta pointer already, so just pass it along to use it
instead of looking it up.
This fixes an issue where after restart we only allocated
a queue of size 16 (due to the ordering issue described
above), and thus never got good throughput again since no
aggregates could be formed on transmit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.4d70868003e8.I3476fee5c12f5b1af2be5e2f38a9df7d66d02b62@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
