IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently the ipq806x dwmac driver is almost always used attached to the
CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii".
Some device came up with a special configuration where the PHY is
directly attached to the GMAC port and in those case phy-mode needs to
be set to "rgmii-id" to make the PHY correctly work and receive packets.
Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id"
(or variants) mode is set, the mode is rejected and probe fails.
Add support also for these phy-modes to correctly setup PHYs that requires
delay applied to tx/rx.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance the error reporting mechanism in the switchdev framework to
provide more informative and user-friendly error messages.
Following feedback from users struggling to understand the implications
of error messages like "failed (err=-28) to add object (id=2)", this
update aims to clarify what operation failed and how this might impact
the system or network.
With this change, error messages now include a description of the failed
operation, the specific object involved, and a brief explanation of the
potential impact on the system. This approach helps administrators and
developers better understand the context and severity of errors,
facilitating quicker and more effective troubleshooting.
Example of the improved logging:
[ 70.516446] ksz-switch spi0.0 uplink: Failed to add Port Multicast
Database entry (object id=2) with error: -ENOSPC (-28).
[ 70.516446] Failure in updating the port's Multicast Database could
lead to multicast forwarding issues.
[ 70.516446] Current HW/SW setup lacks sufficient resources.
This comprehensive update includes handling for a range of switchdev
object IDs, ensuring that most operations within the switchdev framework
benefit from clearer error reporting.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a tracepoint for icmp_send, which can help users to get more
detail information conveniently when icmp abnormal events happen.
1. Giving an usecase example:
=============================
When an application experiences packet loss due to an unreachable UDP
destination port, the kernel will send an exception message through the
icmp_send function. By adding a trace point for icmp_send, developers or
system administrators can obtain detailed information about the UDP
packet loss, including the type, code, source address, destination address,
source port, and destination port. This facilitates the trouble-shooting
of UDP packet loss issues especially for those network-service
applications.
2. Operation Instructions:
==========================
Switch to the tracing directory.
cd /sys/kernel/tracing
Filter for destination port unreachable.
echo "type==3 && code==3" > events/icmp/icmp_send/filter
Enable trace event.
echo 1 > events/icmp/icmp_send/enable
3. Result View:
================
udp_client_erro-11370 [002] ...s.12 124.728002:
icmp_send: icmp_send: type=3, code=3.
From 127.0.0.1:41895 to 127.0.0.1:6666 ulen=23
skbaddr=00000000589b167a
Signed-off-by: Peilin He <he.peilin@zte.com.cn>
Signed-off-by: xu xin <xu.xin16@zte.com.cn>
Reviewed-by: Yunkai Zhang <zhang.yunkai@zte.com.cn>
Cc: Yang Yang <yang.yang29@zte.com.cn>
Cc: Liu Chun <liu.chun2@zte.com.cn>
Cc: Xuexin Jiang <jiang.xuexin@zte.com.cn>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel says:
====================
add DCB and DSCP support for KSZ switches
This patch series is aimed at improving support for DCB (Data Center
Bridging) and DSCP (Differentiated Services Code Point) on KSZ switches.
The main goal is to introduce global DSCP and PCP (Priority Code Point)
mapping support, addressing the limitation of KSZ switches not having
per-port DSCP priority mapping. This involves extending the DSA
framework with new callbacks for managing trust settings for global DSCP
and PCP maps. Additionally, we introduce IEEE 802.1q helpers for default
configurations, benefiting other drivers too.
Change logs are in separate patches.
Compared to v6 this series includes some new patches for DSCP global
mapping support and QoS selftest script for KSZ9477 switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests covering following functionality on KSZ9477 switch family:
- default port priority
- global DSCP to Internal Priority Mapping
- apptrust configuration
This script was tested on KSZ9893R
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switches like Microchip KSZ variants do not support per port DSCP
priority configuration. Instead there is a global DSCP mapping table.
To handle it, we will accept set/del request to any of user ports to
make global configuration and update dcb app entries for all other
ports.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.1q specification provides recommendation and examples which can
be used as good default values for different drivers.
This patch implements mapping examples documented in IEEE 802.1Q-2022 in
Annex I "I.3 Traffic type to traffic class mapping" and IETF DSCP naming
and mapping DSCP to Traffic Type inspired by RFC8325.
This helpers will be used in followup patches for dsa/microchip DCB
implementation.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCB support to get/set trust configuration for different packet
priority information sources. Some switch allow to chose different
source of packet priority classification. For example on KSZ switches it
is possible to configure VLAN PCP and/or DSCP sources.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-05-06 (ice)
This series contains updates to ice driver only.
Paul adds support for additional E830 devices and adjusts naming for
existing E830 devices.
Marcin commonizes a couple of TC setup calls to reduce duplicated code.
Mateusz adds ice_vsi_cfg_params into ice_vsi to consolidate info.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsi
ice: Deduplicate tc action setup
ice: update E830 device ids and comments
ice: add additional E830 device ids
====================
Link: https://lore.kernel.org/r/20240506170827.948682-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some usb drivers set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506143939.3673865-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some usb drivers try to set small skb->truesize and break
core networking stacks.
In this patch, I removed one of the skb->truesize override.
I also replaced one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Link: https://lore.kernel.org/r/20240506142358.3657918-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some usb drivers try to set small skb->truesize and break
core networking stacks.
I replace one skb_clone() by an allocation of a fresh
and small skb, to get minimally sized skbs, like we did
in commit 1e2c611723 ("net: cdc_ncm: reduce skb truesize
in rx path") and 4ce62d5b2f ("net: usb: ax88179_178a:
stop lying about skb->truesize")
Fixes: 361459cd96 ("net: usb: aqc111: Implement RX data path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20240506135546.3641185-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When building with clang, via:
make LLVM=1 -C tools/testing/selftest
...clang warns about three variables that are not initialized in all
cases:
1) The opt_ipproto_off variable is used uninitialized if "testname" is
not "ip". Willem de Bruijn pointed out that this is an actual bug, and
suggested the fix that I'm using here (thanks!).
2) The addr_len is used uninitialized, but only in the assert case,
which bails out, so this is harmless.
3) The family variable in add_listener() is only used uninitialized in
the error case (neither IPv4 nor IPv6 is specified), so it's also
harmless.
Fix by initializing each variable.
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20240506190204.28497-1-jhubbard@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the Dynamic Interrupt Moderation (DIM) library to be built as a
module. This is particularly useful in an Android GKI (Google Kernel
Image) configuration where everything is built as a module, including
Ethernet controller drivers. Having to build DIMLIB into the kernel
image with potentially no user is wasteful.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20240506175040.410446-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netdev CI reports occasional failures with this test
("ERROR: ns2-dX6bUE did not pick up tcp connection from peer").
Add explicit busywait call until the initial connection attempt shows
up in conntrack rather than a one-shot 'must exist' check.
Signed-off-by: Florian Westphal <fw@strlen.de>
Link: https://lore.kernel.org/r/20240506114320.12178-1-fw@strlen.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
make C=1 reports:
warning: Function parameter or struct member 'mrtt' not described in 'ccid2_rtt_estimator'
So document the 'mrtt' parameter.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240505-ccid2_rtt_estimator-kdoc-v1-1-09231fcb9145@quicinc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The embedded PHYs of the 88E6250 family switches are very basic - they
do not even have an Extended Address / Page register.
This adds support for the PHYs to the driver to set up PHY interrupts
and retrieve error stats. To deal with PHYs without a page register,
"simple" variants of all stat handling functions are introduced.
The code should work with all 88E6250 family switches (6250/6220/6071/
6070/6020). The PHY ID 0x01410db0 was read from a 88E6020, under the
assumption that all switches of this family use the same ID. The spec
only lists the prefix 0x01410c00 and leaves the last 10 bits as reserved,
but that seems too unspecific to be useful, as it would cover several
existing PHY IDs already supported by the driver; therefore, the ID read
from the actual hardware is used.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/0695f699cd942e6e06da9d30daeedfd47785bc01.1714643285.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Jurgens says:
====================
Remove RTNL lock protection of CVQ
Currently the buffer used for control VQ commands is protected by the
RTNL lock. Previously this wasn't a major concern because the control VQ
was only used during device setup and user interaction. With the recent
addition of dynamic interrupt moderation the control VQ may be used
frequently during normal operation.
This series removes the RNTL lock dependency by introducing a mutex
to protect the control buffer and writing SGs to the control VQ.
v6:
- Rebased over new stats code.
- Added comment to cvq_lock, init the mutex unconditionally,
and replaced some duplicate code with a goto.
- Fixed minor grammer errors, checkpatch warnings, and clarified
a comment.
v5:
- Changed cvq_lock to a mutex.
- Changed dim_lock to mutex, because it's held taking
the cvq_lock.
- Use spin/mutex_lock/unlock vs guard macros.
v4:
- Protect dim_enabled with same lock as well intr_coal.
- Rename intr_coal_lock to dim_lock.
- Remove some scoped_guard where the error path doesn't
have to be in the lock.
v3:
- Changed type of _offloads to __virtio16 to fix static
analysis warning.
- Moved a misplaced hunk to the correct patch.
v2:
- New patch to only process the provided queue in
virtnet_dim_work
- New patch to lock per queue rx coalescing structure.
====================
Link: https://lore.kernel.org/r/20240503202445.1415560-1-danielj@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The rtnl lock is no longer needed to protect the control buffer and
command VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Once the RTNL locking around the control buffer is removed there can be
contention on the per queue RX interrupt coalescing data. Use a mutex
per queue. A mutex is required because virtnet_send_command can sleep.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since we no longer have to hold the RTNL lock here just do updates for
the specified queue.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The command VQ will no longer be protected by the RTNL lock. Use a
mutex to protect the control buffer header and the VQ.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Allocate memory for the data when it's used. Ideally the struct could
be on the stack, but we can't DMA stack memory. With this change only
the header and status memory are shared between commands, which will
allow using a tighter lock than RTNL.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop storing RSS setting in the control buffer. This is prep work for
removing RTNL lock protection of the control buffer.
Signed-off-by: Daniel Jurgens <danielj@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Heng Qi <hengqi@linux.alibaba.com>
Tested-by: Heng Qi <hengqi@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the MT7530 DSA subdriver configures the MT7530 switch to provide
direct access to switch PHYs, meaning, the switch PHYs listen on the MDIO
bus the switch listens on. The PHY muxing feature makes use of this.
This is problematic as the PHY may be attached before the switch is
initialised, in which case, the PHY will fail to be attached.
Since commit 91374ba537 ("net: dsa: mt7530: support OF-based registration
of switch MDIO bus"), we can describe the switch PHYs on the MDIO bus of
the switch on the device tree. Extend the check to detect PHY muxing when
the PHY is defined on the MDIO bus of the switch on the device tree.
When the PHY is described this way, the switch will be initialised first,
then the switch MDIO bus will be registered. Only after these steps, the
PHY will be attached.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20240430-b4-for-netnext-mt7530-use-switch-mdio-bus-for-phy-muxing-v2-1-9104d886d0db@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Eric Dumazet says:
====================
rtnetlink: more rcu conversions for rtnl_fill_ifinfo()
We want to no longer rely on RTNL for "ip link show" command.
This is a long road, this series takes care of some parts.
====================
Link: https://lore.kernel.org/r/20240503192059.3884225-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We want to be able to run rtnl_fill_ifinfo() under RCU protection
instead of RTNL in the future.
All rtnl_link_ops->get_link_net() methods already using dev_net()
are ready. I added READ_ONCE() annotations on others.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev->xdp_prog is protected by RCU, we can lift RTNL requirement
from rtnl_xdp_prog_skb().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Change dev_change_proto_down() and dev_change_proto_down_reason()
to write once on dev->proto_down and dev->proto_down_reason.
Then rtnl_fill_proto_down() can use READ_ONCE() annotations
and run locklessly.
rtnl_proto_down_size() should assume worst case,
because readng dev->proto_down_reason multiple
times would be racy without RTNL in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the following patch we want to read dev->allmulti
and dev->promiscuity locklessly from rtnl_fill_ifinfo()
In this patch I change __dev_set_promiscuity() and
__dev_set_allmulti() to write these fields (and dev->flags)
only if they succeed, with WRITE_ONCE() annotations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
rtnl_fill_ifinfo() can read dev->tx_queue_len locklessly,
granted we add corresponding READ_ONCE()/WRITE_ONCE() annotations.
Add missing READ_ONCE(dev->tx_queue_len) in teql_enqueue()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We can use netdev_copy_name() to no longer rely on RTNL
to fetch dev->name.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
dev->qdisc can be read using RCU protection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
says:
====================
net: qede: don't restrict error codes
This series fixes the qede driver, so that when a helper function fails,
then the callee should return the returned error code, instead just
assuming that the error is eg. -EINVAL.
The patches in this series, reduces the change of future bugs, so new
error codes can be returned from the helpers, without having to update
the call sites.
This is a follow-up to my recent series "net: qede: avoid overruling
error codes", which fixed the cases where the implicit assumption of
failing with specific error codes had been broken.
https://lore.kernel.org/netdev/20240426091227.78060-1-ast@fiberby.net/
Asbjørn Sloth Tønnesen (3):
net: qede: use return from qede_parse_actions() for flow_spec
net: qede: use return from qede_flow_spec_validate_unused()
net: qede: use return from qede_flow_parse_ports()
.../net/ethernet/qlogic/qede/qede_filter.c | 27 ++++++++++++-------
1 file changed, 18 insertions(+), 9 deletions(-)
====================
Link: https://lore.kernel.org/r/20240503105505.839342-1-ast@fiberby.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling qede_flow_parse_ports(), then the
return code was only used for a non-zero check,
and then -EINVAL was returned.
qede_flow_parse_ports() can currently fail with:
* -EINVAL
This patch changes qede_flow_parse_v{4,6}_common() to
use the actual return code from qede_flow_parse_ports(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When calling qede_flow_spec_validate_unused() then
the return code was only used for a non-zero check,
and then -EOPNOTSUPP was returned.
qede_flow_spec_validate_unused() can currently fail with:
* -EOPNOTSUPP
This patch changes qede_flow_spec_to_rule() to use the
actual return code from qede_flow_spec_validate_unused(),
so it's no longer assumed that all errors are -EOPNOTSUPP.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In qede_flow_spec_to_rule(), when calling
qede_parse_actions() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_actions() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
Commit 319a1d1947 ("flow_offload: check for
basic action hw stats type") broke the implicit
assumption that it could only fail with -EINVAL,
by changing it to return -EOPNOTSUPP, when hardware
stats are requested.
However AFAICT it's not possible to trigger
qede_parse_actions() to return -EOPNOTSUPP, when
called from qede_flow_spec_to_rule(), as hardware
stats can't be requested by ethtool_rx_flow_rule_create().
This patch changes qede_flow_spec_to_rule() to use
the actual return code from qede_parse_actions(),
so it's no longer assumed that all errors are -EINVAL.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>