IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Extend the Tegra194 IO pad table with additional information such as pin
names and 1.8/3.3 V settings to allow a table of voltage control pins to
generated from it. This is similar to what's done for older chips and is
needed to support high-speed modes for SDHCI where switching the pins to
1.8V or 3.3V is necessary.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the firmware header to support uninitialization of UPHY PLL
when the PCIe controller is operating in endpoint mode and host cuts
the PCIe reference clock.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.
Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.
Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to other DSA switches, in the Ocelot cores, the RX filtering is
a much more important concern.
Firstly, the primary use case for Ocelot is non-DSA, so there isn't any
secondary Ethernet MAC [the DSA master's one] to implicitly drop frames
having a DMAC we are not interested in. So the switch driver itself
needs to install FDB entries towards the CPU port module (PGID_CPU) for
the MAC address of each switch port, in each VLAN installed on the port.
Every address that is not whitelisted is implicitly dropped. This is in
order to achieve a behavior similar to N standalone net devices.
Secondly, even in the secondary use case of DSA, such as illustrated by
Felix with the NPI port mode, that secondary Ethernet MAC is present,
but its RX filter is bypassed. This is because the DSA tags themselves
are placed before Ethernet, so the DMAC that the switch ports see is
not seen by the DSA master too (since it's shifter to the right).
So RX filtering is pretty important. A good RX filter won't bother the
CPU in case the switch port receives a frame that it's not interested
in, and there exists no other line of defense.
Ocelot is pretty strict when it comes to RX filtering: non-IP multicast
and broadcast traffic is allowed to go to the CPU port module, but
unknown unicast isn't. This means that traffic reception for any other
MAC addresses than the ones configured on each switch port net device
won't work. This includes use cases such as macvlan or bridging with a
non-Ocelot (so-called "foreign") interface. But this seems to be fine
for the scenarios that the Linux system embedded inside an Ocelot switch
is intended for - it is simply not interested in unknown unicast
traffic, as explained in Allan Nielsen's presentation [0].
On the other hand, the Felix DSA switch is integrated in more
general-purpose Linux systems, so it can't afford to drop that sort of
traffic in hardware, even if it will end up doing so later, in software.
Actually, unknown unicast means more for Felix than it does for Ocelot.
Felix doesn't attempt to perform the whitelisting of switch port MAC
addresses towards PGID_CPU at all, mainly because it is too complicated
to be feasible: while the MAC addresses are unique in Ocelot, by default
in DSA all ports are equal and inherited from the DSA master. This adds
into account the question of reference counting MAC addresses (delayed
ocelot_mact_forget), not to mention reference counting for the VLAN IDs
that those MAC addresses are installed in. This reference counting
should be done in the DSA core, and the fact that it wasn't needed so
far is due to the fact that the other DSA switches don't have the DSA
tag placed before Ethernet, so the DSA master is able to whitelist the
MAC addresses in hardware.
So this means that even regular traffic termination on a Felix switch
port happens through flooding (because neither Felix nor Ocelot learn
source MAC addresses from CPU-injected frames).
So far we've explained that whitelisting towards PGID_CPU:
- helps to reduce the likelihood of spamming the CPU with frames it
won't process very far anyway
- is implemented in the ocelot driver
- is sufficient for the ocelot use cases
- is not feasible in DSA
- breaks use cases in DSA, in the current status (whitelisting enabled
but no MAC address whitelisted)
So the proposed patch allows unknown unicast frames to be sent to the
CPU port module. This is done for the Felix DSA driver only, as Ocelot
seems to be happy without it.
[0]: https://www.youtube.com/watch?v=B1HhxEcU7Jg
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export the cls_flower methods from the ocelot driver and hook them up to
the DSA passthrough layer.
Tables for the VCAP IS2 parameters, as well as half key packing (field
offsets and lengths) need to be defined for the VSC9959 core, as they
are different from Ocelot, mainly due to the different port count.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the definitions for the VCAP IS2 table from ocelot_ace.c, since
it is specific to VSC7514.
The VSC9959 VCAP IS2 table supports more rules (1024 instead of 64) and
has a different width for the action (89 bits instead of 99).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix driver is now using its own PHYLINK instance, not calling into
ocelot_adjust_link. So the port_pcs_init function pointer is an
unnecessary indirection. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IGR_PORT_MASK key width is different between the 11-port VSC7514 and
the 6-port VSC9959 switches. And since IGR_PORT_MASK is one of the first
fields of a VCAP key entry, it means that all further field
offset/length pairs are shifted between the 2.
The ocelot driver performs packing of VCAP half keys with the help of
some preprocessor macros:
- A set of macros for defining the HKO (Half Key Offset) and HKL (Half
Key Length) of each possible key field. The offset of each field is
defined as the sum between the offset and the sum of the previous
field.
- A set of accessors on top of vcap_key_set for shorter (aka less
typing) access to the HKO and HKL of each key field.
Since the field offsets and lengths are different between switches,
defining them through the preprocessor isn't going to fly. So introduce
a structure holding (offset, length) pairs and instantiate it in
ocelot_board.c for VSC7514. In a future patch, a similar structure will
be instantiated in felix_vsc9959.c for NXP LS1028A.
The accessors also need to go. They are based on macro name
concatenation, which is horrible to understand and follow.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot tc-flower offload binds a second flow block callback (apart
from the one for matchall) just because it uses a different block
private structure (ocelot_port_private for matchall, ocelot_port_block
for flower).
But ocelot_port_block just appears to be boilerplate, and doesn't help
with anything in particular at all, it's just useless glue between the
(global!) struct ocelot_acl_block *block pointer, and a per-netdevice
struct ocelot_port_private *priv.
So let's just simplify that, and make struct ocelot_port_private be the
private structure for the block offload. This makes us able to use the
same flow callback as in the case of matchall.
This also reveals that the struct ocelot_acl_block *block is used rather
strangely, as mentioned above: it is defined globally, allocated at
probe time, and freed at unbind time. So just move the structure to the
main ocelot structure, which gives further opportunity for
simplification.
Also get rid of backpointers from struct ocelot_acl_block and struct
ocelot_ace_rule back to struct ocelot, by reworking the function
prototypes, where necessary, to use a more DSA-friendly "struct ocelot
*ocelot, int port" format.
And finally, remove the debugging prints that were added during
development, since they provide no useful information at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update of QMAN the interface to enqueue frame. We now support multiple
enqueue (qbman_swp_enqueue_multiple) and multiple enqueue with
a table of descriptor (qbman_swp_enqueue_multiple_desc).
Signed-off-by: Youri Querry <youri.querry_1@nxp.com>
Acked-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
rpmh_flush() was exported with the idea that an external entity
operation during CPU idle would know when to flush the sleep and wake
TCS. Since, this is not the case when defining a power domain for the
RSC. Remove the function export and instead allow the function to be
called internally.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1580736940-6985-3-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----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=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
The commit 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
moves the sifive L2 cache driver to driver/soc. It did not move the
header file along with the driver. Therefore this patch moves the header
file to driver/soc
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
[paul.walmsley@sifive.com: updated to fix the include guard]
Fixes: 9209fb5189 ("riscv: move sifive_l2_cache.c to drivers/soc")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Since the Felix DSA driver is implementing its own PHYLINK instance due
to SoC differences, it needs access to the few registers that are
common, mainly for flow control.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ocelot switchdev driver and the Felix DSA one need it for different
reasons. Felix (or at least the VSC9959 instantiation in NXP LS1028A) is
integrated with the traditional NXP Layerscape PCS design which does not
support runtime configuration of SerDes protocol. So it needs to
pre-validate the phy-mode from the device tree and prevent PHYLINK from
attempting to change it. For this, it needs to cache it in a private
variable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building this on a 64-bit platform gcc rightly warns that the
error checking is broken (-ENOMEM stored in an u32 does not compare
greater than (unsigned long)-MAX_ERRNO). Instead, change the
ucc_fast_[tr]x_virtual_fifo_base_offset members to s32 and use an
ordinary check-for-negative. Also, this avoids treating 0 as "this
cannot have been returned from qe_muram_alloc() so don't free it".
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
When trying to build this for a 64-bit platform, one gets warnings
from using IS_ERR_VALUE on something which is not sizeof(long).
Instead, change the various *_offset fields to store a signed integer,
and simply check for a negative return from qe_muram_alloc(). Since
qe_muram_free() now accepts and ignores a negative argument, we only
need to make sure these fields are initialized with -1, and we can
just unconditionally call qe_muram_free() in ucc_slow_free().
Note that the error case for us_pram_offset failed to set that field
to 0 (which, as noted earlier, is anyway a bogus sentinel value).
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Nobody uses the return value from cpm_muram_free, and functions that
free resources usually return void. One could imagine a use for a "how
much have I allocated" a la ksize(), but knowing how much one had
access to after the fact is useless.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
There are a number of problems with cpm_muram_alloc() and its
callers. Most callers assign the return value to some variable and
then use IS_ERR_VALUE to check for allocation failure. However, when
that variable is not sizeof(long), this leads to warnings - and it is
indeed broken to do e.g.
u32 foo = cpm_muram_alloc();
if (IS_ERR_VALUE(foo))
on a 64-bit platform, since the condition
foo >= (unsigned long)-ENOMEM
is tautologically false. There are also callers that ignore the
possibility of error, and then there are those that check for error by
comparing the return value to 0...
One could fix that by changing all callers to store the return value
temporarily in an "unsigned long" and test that. However, use of
IS_ERR_VALUE() is error-prone and should be restricted to things which
are inherently long-sized (stuff in pt_regs etc.). Instead, let's aim
for changing to the standard kernel style
int foo = cpm_muram_alloc();
if (foo < 0)
deal_with_it()
some->where = foo;
Changing the return type from unsigned long to s32 (aka signed int)
doesn't change the value that gets stored into any of the callers'
variables except if the caller was storing the result in a u64 _and_
the allocation failed, so in itself this patch should be a no-op.
Another problem with cpm_muram_alloc() is that it can certainly
validly return 0 - and except if some cpm_muram_alloc_fixed() call
interferes, the very first cpm_muram_alloc() call will return just
that. But that shows that both ucc_slow_free() and ucc_fast_free() are
buggy, since they assume that a value of 0 means "that field was never
allocated". We'll later change cpm_muram_free() to accept (and ignore)
a negative offset, so callers can use a sentinel of -1 instead of 0
and just unconditionally call cpm_muram_free().
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
asm/cpm.h under arch/powerpc is now just a wrapper for including
soc/fsl/cpm.h. In order to make the qe.h header usable on other
architectures, use the latter path directly.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Some drivers, e.g. ucc_uart, need definitions from cpm.h. In order to
allow building those drivers for non-ppc based SOCs, move the header
to include/soc/fsl. For now, leave a trivial wrapper at the old
location so drivers can be updated one by one.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The public qe_ic.h header is no longer included by anything but
qe_ic.c. Merge both headers into qe_ic.c, and drop the unused
constants.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
These are only called from within qe_ic.c, so make them static.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
There are no current callers of these functions, and they use the
ppc-specific virq_to_hw(). So removing them gets us one step closer to
building QE support for ARM.
If the functionality is ever actually needed, the code can be dug out
of git and then adapted to work on all architectures, but for future
reference please note that I believe qe_ic_set_priority is buggy: The
"priority < 4" should be "priority <= 4", and in the else branch 24
should be replaced by 28, at least if I'm reading the data sheet right.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
These functions are only ever called through a function pointer, and
therefore it makes no sense for them to be "static inline" - gcc has
no choice but to emit a copy in each translation unit that takes the
address of one of these. Since they are now only referenced from
qe_ic.c, just make them local to that file.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Having to call qe_ic_init() from platform-specific code makes it
awkward to allow building the QE drivers for ARM. It's also a needless
duplication of code, and slightly error-prone: Instead of the caller
needing to know the details of whether the QUICC Engine High and QUICC
Engine Low are actually the same interrupt (see e.g. the machine_is()
in mpc85xx_mds_qeic_init), just let the init function choose the
appropriate handlers after it has parsed the DT and figured it out. If
the two interrupts are distinct, use separate handlers, otherwise use
the handler which first checks the CHIVEC register (for the high
priority interrupts), then the CIVEC.
All existing callers pass 0 for flags, so continue to do that from the
new single caller. Later cleanups will remove that argument
from qe_ic_init and simplify the body, as well as make qe_ic_init into
a proper init function for an IRQCHIP_DECLARE, eliminating the need to
manually look up the fsl,qe-ic node.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The *_ipic and *_mpic handlers are almost identical - the only
difference is that the latter end with an unconditional
chip->irq_eoi() call. Since IPIC does not have ->irq_eoi, we can
reduce some code duplication by calling irq_eoi conditionally.
This is similar to what is already done in mpc8xxx_gpio_irq_cascade().
This leaves the functions slightly misnamed, but that will be fixed in
a subsequent patch.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
The QUICC engine drivers use the powerpc-specific out_be32() etc. In
order to allow those drivers to build for other architectures, those
must be replaced by iowrite32be(). However, on powerpc, out_be32() is
a simple inline function while iowrite32be() is out-of-line. So in
order not to introduce a performance regression on powerpc when making
the drivers work on other architectures, introduce qe_io* helpers.
Also define the qe_{clr,set,clrset}bits* helpers in terms of these new
macros.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Make it clear that these operate on big-endian registers (i.e. use the
iowrite*be primitives) before we introduce more uses of them and allow
the QE drivers to be built for platforms other than ppc32.
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting
-----BEGIN PGP SIGNATURE-----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=3cs2
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Dave Airlie:
"Rob pointed out I missed his pull request for msm-next, it's been in
next for a while outside of my tree so shouldn't cause any unexpected
issues, it has some OCMEM support in drivers/soc that is acked by
other maintainers as it's outside my tree.
Otherwise it's a usual fixes pull, i915, amdgpu, the main ones, with
some tegra, omap, mgag200 and one core fix.
Summary:
msm-next:
- OCMEM support for a3xx and a4xx GPUs.
- a510 support + display support
core:
- mst payload deletion fix
i915:
- uapi alignment fix
- fix for power usage regression due to security fixes
- change default preemption timeout to 640ms from 100ms
- EHL voltage level display fixes
- TGL DGL PHY fix
- gvt - MI_ATOMIC cmd parser fix, CFL non-priv warning
- CI spotted deadlock fix
- EHL port D programming fix
amdgpu:
- VRAM lost fixes on BACO for CI/VI
- navi14 DC fixes
- misc SR-IOV, gfx10 fixes
- XGMI fixes for arcturus
- SRIOV fixes
amdkfd:
- KFD on ppc64le enabled
- page table optimisations
radeon:
- fix for r1xx/2xx register checker.
tegra:
- displayport regression fixes
- DMA API regression fixes
mgag200:
- fix devices that can't scanout except at 0 addr
omap:
- fix dma_addr refcounting"
* tag 'drm-next-2019-12-06' of git://anongit.freedesktop.org/drm/drm: (100 commits)
drm/dp_mst: Correct the bug in drm_dp_update_payload_part1()
drm/omap: fix dma_addr refcounting
drm/tegra: Run hub cleanup on ->remove()
drm/tegra: sor: Make the +5V HDMI supply optional
drm/tegra: Silence expected errors on IOMMU attach
drm/tegra: vic: Export module device table
drm/tegra: sor: Implement system suspend/resume
drm/tegra: Use proper IOVA address for cursor image
drm/tegra: gem: Remove premature import restrictions
drm/tegra: gem: Properly pin imported buffers
drm/tegra: hub: Remove bogus connection mutex check
ia64: agp: Replace empty define with do while
agp: Add bridge parameter documentation
agp: remove unused variable num_segments
agp: move AGPGART_MINOR to include/linux/miscdevice.h
agp: remove unused variable size in agp_generic_create_gatt_table
drm/dp_mst: Fix build on systems with STACKTRACE_SUPPORT=n
drm/radeon: fix r1xx/r2xx register checker for POT textures
drm/amdgpu: fix GFX10 missing CSIB set(v3)
drm/amdgpu: should stop GFX ring in hw_fini
...
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Convert to use skb queue instead of the list of skbs.
The skb queue could provide protection with lock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.
Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.
Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce driver for the External Memory Controller (EMC) found on Tegra30
chips, it controls the external DRAM on the board. The purpose of this
driver is to program memory timing for external memory on the EMC clock
rate change.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Before this change, unbinding the QMan portals did not trigger a
corresponding unbinding of the dpaa_eth making use of it; the first
QMan portal related operation issued afterwards crashed the kernel.
The device link ensures the dpaa_eth dependency upon the qman portal
used is honoured at the QMan portal removal.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the API required to make sure that the devices that use
the QMan portal are unbound when the portal is unbound.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild bot reported the following compiler errors when compiling on
MIPS with CONFIG_QCOM_OCMEM disabled:
In file included from <command-line>:0:0:
>> include/soc/qcom/ocmem.h:43:49: warning: 'struct device' declared
inside parameter list will not be visible outside of this
definition or declaration
static inline struct ocmem *of_get_ocmem(struct device *dev)
^~~~~~
include/soc/qcom/ocmem.h: In function 'of_get_ocmem':
>> include/soc/qcom/ocmem.h:45:9: error: implicit declaration of
function 'ERR_PTR' [-Werror=implicit-function-declaration]
return ERR_PTR(-ENODEV);
^~~~~~~
>> include/soc/qcom/ocmem.h:45:18: error: 'ENODEV' undeclared (first
use in this function)
return ERR_PTR(-ENODEV);
Add the proper includes to fix the compiler errors.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Gabriel Francisco <frc.gabriel@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The OCMEM driver handles allocation and configuration of the On Chip
MEMory that is present on some Snapdragon SoCs. Devices which have
OCMEM do not have GMEM inside the GPU core, so the GPU must instead
use OCMEM to be functional. Since the GPU is currently the only OCMEM
user with an upstream driver, this is just a minimal implementation
sufficient for statically allocating to the GPU it's chunk of OCMEM.
This driver currently does not read the gmu-sram node that is described
in the device tree bindings. The starting memory address of the GPU's
reserved memory region is hardcoded to zero to match what the hardware
expects. The driver can be updated to read the reserved memory regions
from device tree once other users of OCMEM are added upstream.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Co-developed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Gabriel Francisco <frc.gabrielgmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIT1g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym9lwCgrHZlMMvfYNVm6GQ5ge58JJsVTL4AoNatTcL4
hfVMA6pCHWBjV65xVSf6
=Tijw
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver pull request for 5.4-rc1.
As has been happening in previous releases, more and more individual
driver subsystem trees are ending up in here. Now if that is good or
bad I can't tell, but hopefully it makes your life easier as it's more
of an aggregation of trees together to one merge point for you.
Anyway, lots of stuff in here:
- habanalabs driver updates
- thunderbolt driver updates
- misc driver updates
- coresight and intel_th hwtracing driver updates
- fpga driver updates
- extcon driver updates
- some dma driver updates
- char driver updates
- android binder driver updates
- nvmem driver updates
- phy driver updates
- parport driver fixes
- pcmcia driver fix
- uio driver updates
- w1 driver updates
- configfs fixes
- other assorted driver updates
All of these have been in linux-next for a long time with no reported
issues"
* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (200 commits)
misc: mic: Use PTR_ERR_OR_ZERO rather than its implementation
habanalabs: correctly cast variable to __le32
habanalabs: show correct id in error print
habanalabs: stop using the acronym KMD
habanalabs: display card name as sensors header
habanalabs: add uapi to retrieve aggregate H/W events
habanalabs: add uapi to retrieve device utilization
habanalabs: Make the Coresight timestamp perpetual
habanalabs: explicitly set the queue-id enumerated numbers
habanalabs: print to kernel log when reset is finished
habanalabs: replace __le32_to_cpu with le32_to_cpu
habanalabs: replace __cpu_to_le32/64 with cpu_to_le32/64
habanalabs: Handle HW_IP_INFO if device disabled or in reset
habanalabs: Expose devices after initialization is done
habanalabs: improve security in Debug IOCTL
habanalabs: use default structure for user input in Debug IOCTL
habanalabs: Add descriptive name to PSOC app status register
habanalabs: Add descriptive names to PSOC scratch-pad registers
habanalabs: create two char devices per ASIC
habanalabs: change device_setup_cdev() to be more generic
...
Here are the interconnect driver updates for the 5.4-rc1 merge window.
- New feature is the path tagging support that helps with grouping and
aggregating the bandwidth requests into separate buckets based on a tag.
- The first user of the path tagging is the Qualcomm sdm845 driver that
now implements support for wake/sleep sets. This allows consumer drivers
to express their bandwidth needs for the different CPU power states.
- New interconnect driver for the qcs404 platforms and a driver that
communicates bandwidth requests with remote processor over shared memory.
- Cleanups and fixes.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
-----BEGIN PGP SIGNATURE-----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=TVC/
-----END PGP SIGNATURE-----
Merge tag 'icc-5.4-rc1' of https://git.linaro.org/people/georgi.djakov/linux into char-misc-next
Georgi writes:
interconnect patches for 5.4
Here are the interconnect driver updates for the 5.4-rc1 merge window.
- New feature is the path tagging support that helps with grouping and
aggregating the bandwidth requests into separate buckets based on a tag.
- The first user of the path tagging is the Qualcomm sdm845 driver that
now implements support for wake/sleep sets. This allows consumer drivers
to express their bandwidth needs for the different CPU power states.
- New interconnect driver for the qcs404 platforms and a driver that
communicates bandwidth requests with remote processor over shared memory.
- Cleanups and fixes.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.4-rc1' of https://git.linaro.org/people/georgi.djakov/linux:
drivers: qcom: Add BCM vote macro to header
interconnect: qcom: remove COMPILE_TEST from CONFIG_INTERCONNECT_QCOM_QCS404
interconnect: qcom: Add QCS404 interconnect provider driver
interconnect: qcom: Add interconnect RPM over SMD driver
dt-bindings: interconnect: Add Qualcomm QCS404 DT bindings
interconnect: qcom: Add tagging and wake/sleep support for sdm845
interconnect: Add pre_aggregate() callback
interconnect: Add support for path tags
Remove the "struct mtk_smi_iommu" to simplify the code since it has only
one item in it right now.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The "mediatek,larb-id" has already been parsed in MTK IOMMU driver.
It's no need to parse it again in SMI driver. Only clean some codes.
This patch is fit for all the current mt2701, mt2712, mt7623, mt8173
and mt8183.
After this patch, the "mediatek,larb-id" only be needed for mt2712
which have 2 M4Us. In the other SoCs, we can get the larb-id from M4U
in which the larbs in the "mediatek,larbs" always are ordered.
Correspondingly, the larb_nr in the "struct mtk_smi_iommu" could also
be deleted.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
- Support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJdZWFxAAoJEGnX8d3iisJe1/QP/1QlB6bDp36ONuc0wgtvyZhS
/KDfgwyLK89WiH/lc2AgPL6BkFaOBSqpNe9PS8IdjRscGMJFaXnfifKBl2eX/sM3
4nkiIjAb9Fl4dLdaPs/51p+wvHlkdD9pzI5SYJl2IeNCZRNjjixBlaF8fezONtlu
2yuzmikeggcT7NZGnZ5IQGj6CWRm7Drb5J4mfmZu3HJ+BJOnXZpdza3q3WduT3DC
6tUA/xtUXq8sGpylXL2MgA34SbgjBDmxW8Kv32sQp6mipGJwq4jF4+n8rxF/znCe
6ILiqOwp7CjEHmpYTn2cxMC5FTP0BuvnLh/ECEFKUWgIH4/A3zy/RJOKhbZ0P0rV
+vraRvdjOA2/0P6Y1A+cGGYP2c3HwmSgHmtXwd/QRfesX2/Y7jhMlEOXZ9H2K6CC
zTqobUWQ4tFprz1P0H6p1h7Z/tJv/q4TNMZR5tcQyjwT6i7Sw+ReffTnwpPMr92V
GAZu6sahsJCOqRqk0MfaZVa54r+UlE8bbapGZo+7fZ9+UVrxLKgWwfnYbe/6eSHX
osddo3zoLuBrgq2gt/ZMseeQRdRYeH8p/3jgnEws2G/uen7GjAw9m0c3Yrs+ibVS
oNp3DNk8wkzgrLgC7xXhBkwyok85SEoCfZoQg96DXo365G0YyHZyHCI2HzIAP4oy
wtRcqnsQgEtvV1s7RiTU
=CJKr
-----END PGP SIGNATURE-----
Merge tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support for Edge Triggered IRQs in ARC IDU intc
- other fixes here and there
* tag 'arc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: prefer __section from compiler_attributes.h
dt-bindings: IDU-intc: Add support for edge-triggered interrupts
dt-bindings: IDU-intc: Clean up documentation
ARCv2: IDU-intc: Add support for edge-triggered interrupts
ARC: unwind: Mark expected switch fall-throughs
ARC: [plat-hsdk]: allow to switch between AXI DMAC port configurations
ARC: fix typo in setup_dma_ops log message
ARCv2: entry: early return from exception need not clear U & DE bits
This adds support for an optional extra interrupt cell to specify edge
vs level triggered. It is backward compatible with dts files with only
one cell, and will default to level-triggered in such a case.
Note that I had to make a change to idu_irq_set_affinity as well, as
this function was setting the interrupt type to "level" unconditionally,
since this was the only type supported previously.
Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
Convert docs to ReST and add them to the arch-specific
book.
The conversion here was trivial, as almost every file there
was already using an elegant format close to ReST standard.
The changes were mostly to mark literal blocks and add a few
missing section title identifiers.
One note with regards to "--": on Sphinx, this can't be used
to identify a list, as it will format it badly. This can be
used, however, to identify a long hyphen - and "---" is an
even longer one.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> # cxl
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
-----BEGIN PGP SIGNATURE-----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=C+f6
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers
NXP/FSL SoC driver updates for v5.3
DPAA2 Console driver
- Add driver to export two char devices to dump logs for MC and
AIOP
DPAA2 DPIO driver
- Add support for memory backed QBMan portals
- Increase the timeout period to prevent false error
- Add APIs to retrieve QBMan portal probing status
DPAA Qman driver
- Only make liodn fixup on powerpc SoCs with PAMU iommu
* tag 'soc-fsl-next-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qbman_portals: add APIs to retrieve the probing status
soc: fsl: qman: fixup liodns only on ppc targets
soc: fsl: dpio: Add support for memory backed QBMan portals
bus: mc-bus: Add support for mapping shareable portals
soc: fsl: dpio: Increase timeout for QBMan Management Commands
soc: fsl: add DPAA2 console support
Documentation: DT: Add entry for DPAA2 console
soc: fsl: guts: Add definition for LX2160A
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 33 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081038.745679586@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a couple of new APIs to check the probing status of the required
cpu bound qman and bman portals:
'int bman_portals_probed()' and 'int qman_portals_probed()'.
They return the following values.
* 1 if qman/bman portals were all probed correctly
* 0 if qman/bman portals were not yet probed
* -1 if probing of qman/bman portals failed
Portals are considered successful probed if no error occurred during
the probing of any of the portals and if enough portals were probed
to have one available for each cpu.
The error handling paths were slightly rearranged in order to fit this
new functionality without being too intrusive.
Drivers that use qman/bman portal driver services are required to use
these APIs before calling any functions exported by these drivers or
otherwise they will crash the kernel.
First user will be the dpaa1 ethernet driver, coming in a subsequent
patch.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Pull clocksource updates from Ingo Molnar:
"Misc clocksource/clockevent driver updates that came in a bit late but
are ready for v5.2"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
misc: atmel_tclib: Do not probe already used TCBs
clocksource/drivers/timer-atmel-tcb: Convert tc_clksrc_suspend|resume() to static
clocksource/drivers/tcb_clksrc: Rename the file for consistency
clocksource/drivers/timer-atmel-pit: Rework Kconfig option
clocksource/drivers/tcb_clksrc: Move Kconfig option
ARM: at91: Implement clocksource selection
clocksource/drivers/tcb_clksrc: Use tcb as sched_clock
clocksource/drivers/tcb_clksrc: Stop depending on atmel_tclib
ARM: at91: move SoC specific definitions to SoC folder
clocksource/drivers/timer-milbeaut: Cleanup common register accesses
clocksource/drivers/timer-milbeaut: Add shutdown function
clocksource/drivers/timer-milbeaut: Fix to enable one-shot timer
clocksource/drivers/tegra: Rework for compensation of suspend time
clocksource/drivers/sp804: Add COMPILE_TEST to CONFIG_ARM_TIMER_SP804
clocksource/drivers/sun4i: Add a compatible for suniv
dt-bindings: timer: Add Allwinner suniv timer
MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from generic
functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
* Switch to ->exec-op().
- meson:
* Misc cleanups and fixes.
* New OOB layout.
- Sunxi:
* A23/A33 NAND DMA support.
- Ingenic:
* Full reorganization and cleanup.
* Clear separation between NAND controller and ECC engine.
* Support JZ4740 an JZ4725B.
- Denali:
* Clear controller/chip separation.
* ->exec_op() migration.
* Various cleanups.
- fsl_elbc:
* Enable software ECC support.
- Atmel:
* Sam9x60 support.
- GPMI:
* Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
* Avoid crossing 4K address boundary on read/write
* Add support for Intel Comet Lake SPI serial flash
-----BEGIN PGP SIGNATURE-----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=HXap
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- New AFS partition parser
- Update MAINTAINERS entry
- Use of fall-throughs markers
NAND core changes:
- Support having the bad block markers in either the first, second or
last page of a block. The combination of all three location is now
possible.
- Constification of NAND_OP_PARSER(_PATTERN) elements.
- Generic NAND DT bindings changed to yaml format (can be used to
check the proposed bindings. First platform to be fully supported:
sunxi.
- Stopped using several legacy hooks.
- Preparation to use the generic NAND layer with the addition of
several helpers and the removal of the struct nand_chip from
generic functions.
- Kconfig cleanup to prepare the introduction of external ECC engines
support.
- Fallthrough comments.
- Introduction of the SPI-mem dirmap API for SPI-NAND devices.
Raw NAND controller drivers changes:
- nandsim:
- Switch to ->exec-op().
- meson:
- Misc cleanups and fixes.
- New OOB layout.
- Sunxi:
- A23/A33 NAND DMA support.
- Ingenic:
- Full reorganization and cleanup.
- Clear separation between NAND controller and ECC engine.
- Support JZ4740 an JZ4725B.
- Denali:
- Clear controller/chip separation.
- ->exec_op() migration.
- Various cleanups.
- fsl_elbc:
- Enable software ECC support.
- Atmel:
- Sam9x60 support.
- GPMI:
- Introduce the GPMI_IS_MXS() macro.
- Various trivial/spelling/coding style fixes.
SPI NOR core changes:
- Print all JEDEC ID bytes on error
- Fix comment of spi_nor_find_best_erase_type()
- Add region locking flags for s25fl512s
SPI NOR controller drivers changes:
- intel-spi:
- Avoid crossing 4K address boundary on read/write
- Add support for Intel Comet Lake SPI serial flash"
* tag 'mtd/for-5.2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: part: fix incorrect format specifier for an unsigned long long
mtd: lpddr_cmds: Mark expected switch fall-through
mtd: phram: Mark expected switch fall-throughs
mtd: cfi_cmdset_0002: Mark expected switch fall-throughs
mtd: cfi_util: mark expected switch fall-throughs
MAINTAINERS: MTD Git repository is hosted on kernel.org
MAINTAINERS: Update jffs2 entry
mtd: afs: add v2 partition parsing
mtd: afs: factor the IIS read into partition parser
mtd: afs: factor footer parsing into the v1 part parsing
mtd: factor out v1 partition parsing
mtd: afs: simplify partition detection
mtd: afs: simplify partition parsing
mtd: partitions: Add OF support to AFS partitions
mtd: partitions: Add AFS partitions DT bindings
mtd: afs: Move AFS partition parser to parsers subdir
mtd: maps: Make uclinux_ram_map static
mtd: maps: Allow MTD_PHYSMAP with MTD_RAM
MAINTAINERS: Add myself as MTD maintainer
MAINTAINERS: Remove my name from the MTD and NAND entries
...
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Keep generic names, as there are no conflicts with previous
SFR definitions.
While touching bits, update AT91_OHCIICR_USB_SUSPEND to use
GENMASK, replace unused AT91_OHCIICR_SUSPEND_A/B/C with a more
generic macro, align values on tab-width.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Including:
- A big cleanup and optimization patch-set for the
Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and
Intel VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some
aliased devices, needed for future devices which send IRQ
messages from more than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable
outside of the IOMMU code
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=cKsD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- A big cleanup and optimization patch-set for the Tegra GART driver
- Documentation updates and fixes for the IOMMU-API
- Support for page request in Intel VT-d scalable mode
- Intel VT-d dma_[un]map_resource() support
- Updates to the ATS enabling code for PCI (acked by Bjorn) and Intel
VT-d to align with the latest version of the ATS spec
- Relaxed IRQ source checking in the Intel VT-d driver for some aliased
devices, needed for future devices which send IRQ messages from more
than on request-ID
- IRQ remapping driver for Hyper-V
- Patches to make generic IOVA and IO-Page-Table code usable outside of
the IOMMU code
- Various other small fixes and cleanups
* tag 'iommu-updates-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (60 commits)
iommu/vt-d: Get domain ID before clear pasid entry
iommu/vt-d: Fix NULL pointer reference in intel_svm_bind_mm()
iommu/vt-d: Set context field after value initialized
iommu/vt-d: Disable ATS support on untrusted devices
iommu/mediatek: Fix semicolon code style issue
MAINTAINERS: Add Hyper-V IOMMU driver into Hyper-V CORE AND DRIVERS scope
iommu/hyper-v: Add Hyper-V stub IOMMU driver
x86/Hyper-V: Set x2apic destination mode to physical when x2apic is available
PCI/ATS: Add inline to pci_prg_resp_pasid_required()
iommu/vt-d: Check identity map for hot-added devices
iommu: Fix IOMMU debugfs fallout
iommu: Document iommu_ops.is_attach_deferred()
iommu: Document iommu_ops.iotlb_sync_map()
iommu/vt-d: Enable ATS only if the device uses page aligned address.
PCI/ATS: Add pci_ats_page_aligned() interface
iommu/vt-d: Fix PRI/PASID dependency issue.
PCI/ATS: Add pci_prg_resp_pasid_required() interface.
iommu/vt-d: Allow interrupts from the entire bus for aliased devices
iommu/vt-d: Add helper to set an IRTE to verify only the bus number
iommu: Fix flush_tlb_all typo
...
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
-----BEGIN PGP SIGNATURE-----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=t5+u
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom ARM/ARM64/MIPS based SoCs changes
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
* tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4)
soc: bcm: bcm2835-pm: Make local symbol static
soc: bcm: Make PM driver default for BCM2835
soc: bcm: bcm2835-pm: Add support for power domains under a new binding.
bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.
dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4)
firmware: raspberrypi: notify VC4 firmware of a reboot
soc: bcm2835: sync firmware properties with downstream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a couple of miscellaneous fixes for minor issues and a
largish rework of the PMC driver to make it work on systems where the
PMC has been locked down and can only be accessed from secure firmware.
-----BEGIN PGP SIGNATURE-----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=C9+u
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.1-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.1-rc1
This contains a couple of miscellaneous fixes for minor issues and a
largish rework of the PMC driver to make it work on systems where the
PMC has been locked down and can only be accessed from secure firmware.
* tag 'tegra-for-5.1-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Support systems where PMC is marked secure
soc/tegra: pmc: Explicitly initialize all fields
soc/tegra: pmc: Make alignment consistent
soc/tegra: pmc: Pass struct tegra_pmc * where possible
soc/tegra: pmc: Make tegra_powergate_is_powered() a local function
soc/tegra: pmc: Add missing kerneldoc
soc/tegra: pmc: Sort includes alphabetically
soc/tegra: pmc: Use TEGRA186_ prefix for GPIO names
soc/tegra: fuse: Fix typo in tegra210_init_speedo_data
soc/tegra: fuse: Fix illegal free of IO base address
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These changes add support for BPMP on Tegra210.
-----BEGIN PGP SIGNATURE-----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=8HHq
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.1-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
firmware: tegra: Changes for v5.1-rc1
These changes add support for BPMP on Tegra210.
* tag 'tegra-for-5.1-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware/tegra: Enable Tegra186 BPMP support on Tegra194
firmware: tegra: Conditionally support SoC generations
firmware: tegra: bpmp-tegra186: Remove unused includes
firmware: tegra: add bpmp driver for Tegra210
firmware: tegra: Refactor BPMP driver
firmware: tegra: Reword messaging terminology
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds driver for Tegra210 BPMP firmware.
The BPMP is a specific processor in Tegra210 chip, which runs firmware
for assisting in entering deep low power states (suspend to ram), and
offloading DRAM memory clock scaling on some platforms.
Based on work by Sivaram Nair <sivaramn@nvidia.com>
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Split BPMP driver into common and chip specific parts to facilitate
adding support for previous and future Tegra chips that are using BPMP
as co-processor.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now there are no more external users of tegra_powergate_is_powered(),
make this a local function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device-tree binding has been changed. There is no separate GART device
anymore, it is squashed into the Memory Controller. Integrate GART module
with the MC in a way it is done for the SMMU on Tegra30+.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The tegra20-mc device-tree binding has been changed, GART has been
squashed into Memory Controller and now the clock property is mandatory
for Tegra20, the DT compatible has been changed as well. Adapt driver to
the DT changes.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
In all QBMan registers, the buffer pool id field is two bytes long.
The low level qbman APIs reflect this, but the high level DPIO ones
use u32. Modify them in order to avoid implicit downcasts.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Automatically add a device link between the actual device requesting the
dpaa2_io_service_register and the underlying dpaa2_io used. This link
will ensure that when a DPIO device, which is indirectly used by other
devices, is unbound any consumer devices will be also unbound from their
drivers.
For example, any DPNI, bound to the dpaa2-eth driver, which is using
DPIO devices will be unbound before its supplier device.
Also, add a new parameter to the dpaa2_io_service_[de]register functions
to specify the requesting device (ie the consumer).
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add a new field in the dpaa2_io structure to hold a backpointer to the
actual DPIO device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add latest firmware property tags from the latest Raspberry Pi downstream
kernel. This is needed to use the reboot notify in the following
commit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The current implementation of the dpio driver uses a static next_cpu
variable to keep track of the index of the next cpu available. This
approach does not handle well unbinding and binding dpio devices in a
random order. For example, unbinding a dpio and then binding it again
with the driver, will generate the below error:
$ echo dpio.5 > /sys/bus/fsl-mc/drivers/fsl_mc_dpio/unbind
$ echo dpio.5 > /sys/bus/fsl-mc/drivers/fsl_mc_dpio/bind
[ 103.946380] fsl_mc_dpio dpio.5: probe failed. Number of DPIOs exceeds
NR_CPUS.
[ 103.955157] fsl_mc_dpio dpio.5: fsl_mc_driver_probe failed: -34
-bash: echo: write error: No such device
Fix this error by keeping a global cpumask of unused cpus that will be
updated at every dpaa2_dpio_[probe,remove].
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64 C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
+ misc cleanups across several platforms
-----BEGIN PGP SIGNATURE-----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=yEX2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Misc driver updates for platforms, many of them power related.
- Rockchip adds power domain support for rk3066 and rk3188
- Amlogic adds a power measurement driver
- Allwinner adds SRAM support for three platforms (F1C100, H5, A64
C1)
- Wakeup and ti-sysc (platform bus) fixes for OMAP/DRA7
- Broadcom fixes suspend/resume with Thumb2 kernels, and improves
stability of a handful of firmware/platform interfaces
- PXA completes their conversion to dmaengine framework
- Renesas does a bunch of PM cleanups across many platforms
- Tegra adds support for suspend/resume on T186/T194, which includes
some driver cleanups and addition of wake events
- Tegra also adds a driver for memory controller (EMC) on Tegra2
- i.MX tweaks power domain bindings, and adds support for i.MX8MQ in
GPC
- Atmel adds identifiers and LPDDR2 support for a new SoC, SAM9X60
and misc cleanups across several platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: at91: add support in soc driver for new SAM9X60
ARM: at91: add support in soc driver for LPDDR2 SiP
memory: omap-gpmc: Use of_node_name_eq for node name comparisons
bus: ti-sysc: Check for no-reset and no-idle flags at the child level
ARM: OMAP2+: Check also the first dts child for hwmod flags
soc: amlogic: meson-clk-measure: Add missing REGMAP_MMIO dependency
soc: imx: gpc: Increase GPC_CLK_MAX to 7
soc: renesas: rcar-sysc: Fix power domain control after system resume
soc: renesas: rcar-sysc: Merge PM Domain registration and linking
soc: renesas: rcar-sysc: Remove rcar_sysc_power_{down,up}() helpers
soc: renesas: r8a77990-sysc: Fix initialization order of 3DG-{A,B}
dt-bindings: sram: sunxi: Add compatible for the A64 SRAM C1
dt-bindings: sram: sunxi: Add bindings for the H5 with SRAM C1
dt-bindings: sram: Add Allwinner suniv F1C100s
soc: sunxi: sram: Add support for the H5 SoC system control
soc: sunxi: sram: Enable EMAC clock access for H3 variant
soc: imx: gpcv2: add support for i.MX8MQ SoC
soc: imx: gpcv2: move register access table to domain data
soc: imx: gpcv2: prefix i.MX7 specific defines
dmaengine: pxa: make the filter function internal
...
Pull networking updates from David Miller:
1) New ipset extensions for matching on destination MAC addresses, from
Stefano Brivio.
2) Add ipv4 ttl and tos, plus ipv6 flow label and hop limit offloads to
nfp driver. From Stefano Brivio.
3) Implement GRO for plain UDP sockets, from Paolo Abeni.
4) Lots of work from Michał Mirosław to eliminate the VLAN_TAG_PRESENT
bit so that we could support the entire vlan_tci value.
5) Rework the IPSEC policy lookups to better optimize more usecases,
from Florian Westphal.
6) Infrastructure changes eliminating direct manipulation of SKB lists
wherever possible, and to always use the appropriate SKB list
helpers. This work is still ongoing...
7) Lots of PHY driver and state machine improvements and
simplifications, from Heiner Kallweit.
8) Various TSO deferral refinements, from Eric Dumazet.
9) Add ntuple filter support to aquantia driver, from Dmitry Bogdanov.
10) Batch dropping of XDP packets in tuntap, from Jason Wang.
11) Lots of cleanups and improvements to the r8169 driver from Heiner
Kallweit, including support for ->xmit_more. This driver has been
getting some much needed love since he started working on it.
12) Lots of new forwarding selftests from Petr Machata.
13) Enable VXLAN learning in mlxsw driver, from Ido Schimmel.
14) Packed ring support for virtio, from Tiwei Bie.
15) Add new Aquantia AQtion USB driver, from Dmitry Bezrukov.
16) Add XDP support to dpaa2-eth driver, from Ioana Ciocoi Radulescu.
17) Implement coalescing on TCP backlog queue, from Eric Dumazet.
18) Implement carrier change in tun driver, from Nicolas Dichtel.
19) Support msg_zerocopy in UDP, from Willem de Bruijn.
20) Significantly improve garbage collection of neighbor objects when
the table has many PERMANENT entries, from David Ahern.
21) Remove egdev usage from nfp and mlx5, and remove the facility
completely from the tree as it no longer has any users. From Oz
Shlomo and others.
22) Add a NETDEV_PRE_CHANGEADDR so that drivers can veto the change and
therefore abort the operation before the commit phase (which is the
NETDEV_CHANGEADDR event). From Petr Machata.
23) Add indirect call wrappers to avoid retpoline overhead, and use them
in the GRO code paths. From Paolo Abeni.
24) Add support for netlink FDB get operations, from Roopa Prabhu.
25) Support bloom filter in mlxsw driver, from Nir Dotan.
26) Add SKB extension infrastructure. This consolidates the handling of
the auxiliary SKB data used by IPSEC and bridge netfilter, and is
designed to support the needs to MPTCP which could be integrated in
the future.
27) Lots of XDP TX optimizations in mlx5 from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1845 commits)
net: dccp: fix kernel crash on module load
drivers/net: appletalk/cops: remove redundant if statement and mask
bnx2x: Fix NULL pointer dereference in bnx2x_del_all_vlans() on some hw
net/net_namespace: Check the return value of register_pernet_subsys()
net/netlink_compat: Fix a missing check of nla_parse_nested
ieee802154: lowpan_header_create check must check daddr
net/mlx4_core: drop useless LIST_HEAD
mlxsw: spectrum: drop useless LIST_HEAD
net/mlx5e: drop useless LIST_HEAD
iptunnel: Set tun_flags in the iptunnel_metadata_reply from src
net/mlx5e: fix semicolon.cocci warnings
staging: octeon: fix build failure with XFRM enabled
net: Revert recent Spectre-v1 patches.
can: af_can: Fix Spectre v1 vulnerability
packet: validate address length if non-zero
nfc: af_nfc: Fix Spectre v1 vulnerability
phonet: af_phonet: Fix Spectre v1 vulnerability
net: core: Fix Spectre v1 vulnerability
net: minor cleanup in skb_ext_add()
net: drop the unused helper skb_ext_get()
...
Add FQ (Frame Queue) and BP (Buffer Pool) query APIs that
users of QBMan can invoke to see the status of the queues
and pools that they are using.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SMP is disabled, the tegra clk driver now fails to build:
drivers/clk/tegra/clk-tegra30.c: In function ‘tegra30_cpu_rail_off_ready’:
drivers/clk/tegra/clk-tegra30.c:1151:2: error: implicit declaration of function ‘tegra_pmc_cpu_is_powered’ [-Werror=implicit-function-declaration]
cpu_pwr_status = tegra_pmc_cpu_is_powered(1) ||
^
Fix the above error by removing the CONFIG_SMP ifdef around the
declaration around the PMC CPU APIs because although these are not
needed for non-SMP configurations, there is no harm in including these
for non-SMP builds either.
Fixes: 61866523ed6e ("clk: tegra30: Use Tegra CPU powergate helper function")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These changes update the BPMP ABI header and implement a new variant of
the BPMP firmware version tag query if supported.
-----BEGIN PGP SIGNATURE-----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=hyDw
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
firmware: tegra: Changes for v4.21-rc1
These changes update the BPMP ABI header and implement a new variant of
the BPMP firmware version tag query if supported.
* tag 'tegra-for-4.21-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: Use in-band messages for firmware version query
soc/tegra: bpmp: Update ABI header
firmware: tegra: Print version tag at full
firmware: tegra: Switch to global mrq_is_supported()
firmware: tegra: Add helper to check for supported MRQs
Signed-off-by: Olof Johansson <olof@lixom.net>
These changes are mostly cleanups to the PMC driver, but they also add
support for wake events on Tegra186 and Tegra194, which can be used to
wake the system from sleep. With this and the corresponding device
tree additions suspend/resume is finally working on these SoCs.
-----BEGIN PGP SIGNATURE-----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=lNWz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.21-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
soc/tegra: Changes for v4.21-rc1
These changes are mostly cleanups to the PMC driver, but they also add
support for wake events on Tegra186 and Tegra194, which can be used to
wake the system from sleep. With this and the corresponding device
tree additions suspend/resume is finally working on these SoCs.
* tag 'tegra-for-4.21-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add initial Tegra194 wake events
soc/tegra: pmc: Add initial Tegra186 wake events
soc/tegra: pmc: Add wake event support
soc/tegra: pmc: Add Tegra194 support
soc/tegra: pmc: Change to use DEFINE_SHOW_ATTRIBUTE macro
soc/tegra: Don't leak device tree node reference
soc/tegra: fuse: Remove duplicated function declaration
soc/tegra: pmc: Drop locking from tegra_powergate_is_powered()
soc/tegra: pmc: Add sysfs entries for reset info
soc/tegra: pmc: Don't power-up XUSB power-domains
Signed-off-by: Olof Johansson <olof@lixom.net>
* Fix llcc license, includes, and error checks
* Remove use of memcpy in cmd-db and fix API breakage
* Add QCS404 compatible to SMD-RPM
* Minor fixes for QMI
* Add irq clear handling in QCOM Geni SE during init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hySS
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Qualcomm ARM Based Driver Updates for v4.21
* Fix llcc license, includes, and error checks
* Remove use of memcpy in cmd-db and fix API breakage
* Add QCS404 compatible to SMD-RPM
* Minor fixes for QMI
* Add irq clear handling in QCOM Geni SE during init
* tag 'qcom-drivers-for-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
drm: msm: Check cmd_db_read_aux_data() for failure
soc: qcom: smd-rpm: Add QCS404 compatible
soc: qcom: llcc-slice: Remove duplicated include from llcc-slice.c
soc: qcom: cmd-db: Stop memcpy()ing in cmd_db_read_aux_data()
soc: qcom: cmd-db: Remove memcpy()ing from cmd_db_get_header()
soc: qcom: Drop help text for QCOM_QMI_HELPERS
soc: qcom: qmi_interface: Limit txn ids to U16_MAX
soc: qcom: llcc-slice: Add error checks for API functions
soc: qcom/llcc: add MODULE_LICENSE tag
soc: qcom: Add irq clear handling during SE init
Signed-off-by: Olof Johansson <olof@lixom.net>
Check that the values received by the portal interrupt coalesce
change APIs are in range.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Let's change the function signature to return the pointer to memory or
an error pointer on failure, and take an argument that lets us return
the size of the aux data read. This way we can remove the
cmd_db_read_aux_data_len() API entirely and also get rid of the memcpy
operation from cmd_db to the caller. Updating the only user of this code
shows that making this change allows us to remove a function and put the
lookup where the user is.
Cc: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The function tegra_read_chipid() is declared twice in fuse.h. Remove the
redundant declaration.
Signed-off-by: Bo Yan <byan@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the firmware header file to a more recent version. The major
changes in the new version are:
* add a new MRQ for firmware version query ABI and deprecates the old
* add ABI to query Tegra194 CPU frequency limits
* add ABI to control subset of PCIE UPHY state
The new header contains also some editorial changes to the
documentation.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Sivaram Nair <sivaramn@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a helper function to check that firmware is supporting a given MRQ
command.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Sivaram Nair <sivaramn@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl" interface
that was a little controversial at first, but the version we merged
solved that by not exposing arbitrary firmware calls to user space.
- The Amlogic Meson platform gains a "canvas" driver that is used
for video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for
their respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in particular
a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem"
device driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=c/PQ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The most noteworthy SoC driver changes this time include:
- The TEE subsystem gains an in-kernel interface to access the TEE
from device drivers.
- The reset controller subsystem gains a driver for the Qualcomm
Snapdragon 845 Power Domain Controller.
- The Xilinx Zynq platform now has a firmware interface for its
platform management unit. This contains a firmware "ioctl"
interface that was a little controversial at first, but the version
we merged solved that by not exposing arbitrary firmware calls to
user space.
- The Amlogic Meson platform gains a "canvas" driver that is used for
video processing and shared between different high-level drivers.
The rest is more of the usual, mostly related to SoC specific power
management support and core drivers in drivers/soc:
- Several Renesas SoCs (RZ/G1N, RZ/G2M, R-Car V3M, RZ/A2M) gain new
features related to power and reset control.
- The Mediatek mt8183 and mt6765 SoC platforms gain support for their
respective power management chips.
- A new driver for NXP i.MX8, which need a firmware interface for
power management.
- The SCPI firmware interface now contains support estimating power
usage of performance states
- The NVIDIA Tegra "pmc" driver gains a few new features, in
particular a pinctrl interface for configuring the pads.
- Lots of small changes for Qualcomm, in particular the "smem" device
driver.
- Some cleanups for the TI OMAP series related to their sysc
controller.
Additional cleanups and bugfixes in SoC specific drivers include the
Meson, Keystone, NXP, AT91, Sunxi, Actions, and Tegra platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (129 commits)
firmware: tegra: bpmp: Implement suspend/resume support
drivers: clk: Add ZynqMP clock driver
dt-bindings: clock: Add bindings for ZynqMP clock driver
firmware: xilinx: Add zynqmp IOCTL API for device control
Documentation: xilinx: Add documentation for eemi APIs
MAINTAINERS: imx: include drivers/firmware/imx path
firmware: imx: add misc svc support
firmware: imx: add SCU firmware driver support
reset: Fix potential use-after-free in __of_reset_control_get()
dt-bindings: arm: fsl: add scu binding doc
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
reset: qcom: PDC Global (Power Domain Controller) reset controller
dt-bindings: reset: Add PDC Global binding for SDM845 SoCs
reset: Grammar s/more then once/more than once/
bus: ti-sysc: Just use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS
...
Extract error information from rx and tx buffer descriptors,
and update error counters.
Signed-off-by: Mathias Thore <mathias.thore@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Update qbman driver to better work with CPU hotplug
- Add Kconfig dependency of 64-bit DMA addressing for qbman driver
- Use last reponse to determine valid bit for qbman driver
- Defer bman_portals probe if bman is not probed
- Add interrupt coalescing APIs to qbman driver
-----BEGIN PGP SIGNATURE-----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=2fhR
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-next-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into next/drivers
NXP/FSL SoC drivers updates for v4.20 take 2
- Update qbman driver to better work with CPU hotplug
- Add Kconfig dependency of 64-bit DMA addressing for qbman driver
- Use last reponse to determine valid bit for qbman driver
- Defer bman_portals probe if bman is not probed
- Add interrupt coalescing APIs to qbman driver
* tag 'soc-fsl-next-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qbman: add interrupt coalesce changing APIs
soc: fsl: bman_portals: defer probe after bman's probe
soc: fsl: qbman: Use last response to determine valid bit
soc: fsl: qbman: Add 64 bit DMA addressing requirement to QBMan
soc: fsl: qbman: replace CPU 0 with any online CPU in hotplug handlers
soc: fsl: qbman: Check if CPU is offline when initializing portals
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since HSIO address space can be accessed by different drivers, let's
simplify the register address definitions so that it can be easily used
by all drivers and put the register address definition in the
include/soc/mscc/ocelot_hsio.h header file.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since HSIO address space can be used by different drivers (PLL, SerDes
muxing, temperature sensor), let's move it somewhere it can be included
by all drivers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the APIs required to control the QMan portal interrupt coalescing
settings.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add a couple of new APIs to check the probing status of qman and bman:
'int bman_is_probed()' and 'int qman_is_probed()'.
They return the following values.
* 1 if qman/bman were probed correctly
* 0 if qman/bman were not yet probed
* -1 if probing of qman/bman failed
Drivers that use qman/bman driver services are required to use these
APIs before calling any functions exported by qman or bman drivers
or otherwise they will crash the kernel.
The APIs will be used in the following couple of qbman portal patches
and later in the series in the dpaa1 ethernet driver.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add support for Congestion State Change Notifications (CSCN), which
allow DPIO users to be notified when a congestion group changes its
state (due to hitting the entrance / exit threshold).
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for dpaa2_fd_list format, i.e. dpaa2_fl_entry structure
and accessors.
Frame list entries (FLEs) are similar, but not identical to FDs:
+ "F" (final) bit
- FMT[b'01] is reserved
- DD, SC, DROPP bits (covered by "FD compatibility" field in FLE case)
- FLC[5:0] not used for stashing
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This commit adds back functions removed in
commit a211c8170b ("staging: fsl-mc/dpio: remove couple of unused functions")
since dpseci object will make use of them.
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make tegra_io_pad_set_voltage() and tegra_io_pad_get_voltage() static
and remove the prototypes from pmc.h. Remove enum tegra_io_pad_voltage
and use the defines from <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
instead.
These functions aren't used outside of the pmc driver and new use cases
should use the pinctrl interface instead.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Implement support for the PMC_IMPL_E_33V_PWR register which replaces
PMC_PWR_DET register interface of the SoC generations preceding
Tegra186. Also add the voltage bit offsets to the tegra186_io_pads[]
table and the AO_HV pad.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Moves DPAA2 DPIO driver from staging to fsl/soc
Adds multiple-pin support to QE gpio driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJbV51GAAoJEIbcUA77rBVUzB0P/1l1XZ14jlyIc4PI8eiEKx2i
Emet7qvEaeeoRYI06Dqtm+VkNYjO2Ev4n+XQYPTZGP3/b+cPh7CEI1N/L+ULFGop
HtD0FsOikvfql7BMHvGCCRLzFYHYjDNpg8JCB/3q+aOhI3/8HQyVIAEyggh1Ztam
NSmMQXHwdB8d1qAGcSYGttiJCIxLcDUtVEGcF6ZN6Lg3orpDHEbCceeQ10f1yayQ
PZuM+F1YFM4Lp17gt92caMSKENsN0Kyk/7lEVPHq0ANGMvVsHIVtZGJML+/ulaeI
v7FZrEicYJVu8LDkFAPeg3qK+O6WirOa9bQEctH7jia43QWZAZ9EROCkFOzlEwx6
+AmOB5BsqMTQsz7HppNOqB6v3zgK898UIYavGeud0c/SaIqAW3uVkKvHLKxXd/uY
K2eyvxcBs9ttK+qLopLWO1QzwWAvedIZFjSDCYpGcWDlhZR1lOqoC1u6wSApX/ZC
h7SGOOhjmzZBLtS89hHn7LnzN7RI6teNmC9uhdFtY+55IVfcRAzX3m2ym/TWPRc8
dQNA/vNMuXK2Hv8rtElqIEVUvWil3p86+640m1fnbkljmSqgzp8vAIAopUbhq2Qj
QytaQBwWPcIoAgKQjLMOypjyCTyNs1oFhKycGlwL4Jq5BwxWq27714fl+dSk4JMz
itj5Fz0+82WeDts7CBjM
=9CHI
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into next/drivers
Various updates to soc/fsl for 4.19
Moves DPAA2 DPIO driver from staging to fsl/soc
Adds multiple-pin support to QE gpio driver
* tag 'soc-fsl-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
Signed-off-by: Olof Johansson <olof@lixom.net>
Move the NXP DPIO (Datapath I/O Driver) out of the
drivers/staging directory and into the drivers/soc/fsl directory.
The DPIO driver enables access to Queue and Buffer Manager (QBMAN)
hardware on NXP DPAA2 devices. This is a prerequisite to moving the
DPAA2 Ethernet driver out of staging.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Platform drivers need make a lot of resource state requests at the same
time, say, at the start or end of an usecase. It can be quite
inefficient to send each request separately. Instead they can give the
RPMH library a batch of requests to be sent and wait on the whole
transaction to be complete.
rpmh_write_batch() is a blocking call that can be used to send multiple
RPMH command sets. Each RPMH command set is set asynchronously and the
API blocks until all the command sets are complete and receive their
tx_done callbacks.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Platform drivers that want to send a request but do not want to block
until the RPMH request completes have now a new API -
rpmh_write_async().
The API allocates memory and send the requests and returns the control
back to the platform driver. The tx_done callback from the controller is
handled in the context of the controller's thread and frees the
allocated memory. This API allows RPMH requests from atomic contexts as
well.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Active state requests are sent immediately to the RSC controller, while
sleep and wake state requests are cached in this driver to avoid taxing
the RSC controller repeatedly. The cached values will be sent to the
controller when the rpmh_flush() is called.
Generally, flushing is a system PM activity and may be called from the
system PM drivers when the system is entering suspend or deeper sleep
modes during cpuidle.
Also allow invalidating the cached requests, so they may be re-populated
again.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
[rplsssn: remove unneeded semicolon, address line over 80chars error]
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Sending RPMH requests and waiting for response from the controller
through a callback is common functionality across all platform drivers.
To simplify drivers, add a library functions to create RPMH client and
send resource state requests.
rpmh_write() is a synchronous blocking call that can be used to send
active state requests.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add controller driver for QCOM SoCs that have hardware based shared
resource management. The hardware IP known as RSC (Resource State
Coordinator) houses multiple Direct Resource Voter (DRV) for different
execution levels. A DRV is a unique voter on the state of a shared
resource. A Trigger Control Set (TCS) is a bunch of slots that can house
multiple resource state requests, that when triggered will issue those
requests through an internal bus to the Resource Power Manager Hardened
(RPMH) blocks. These hardware blocks are capable of adjusting clocks,
voltages, etc. The resource state request from a DRV are aggregated
along with state requests from other processors in the SoC and the
aggregate value is applied on the resource.
Some important aspects of the RPMH communication -
- Requests are <addr, value> with some header information
- Multiple requests (upto 16) may be sent through a TCS, at a time
- Requests in a TCS are sent in sequence
- Requests may be fire-n-forget or completion (response expected)
- Multiple TCS from the same DRV may be triggered simultaneously
- Cannot send a request if another request for the same addr is in
progress from the same DRV
- When all the requests from a TCS are complete, an IRQ is raised
- The IRQ handler needs to clear the TCS before it is available for
reuse
- TCS configuration is specific to a DRV
- Platform drivers may use DRV from different RSCs to make requests
Resource state requests made when CPUs are active are called 'active'
state requests. Requests made when all the CPUs are powered down (idle
state) are called 'sleep' state requests. They are matched by a
corresponding 'wake' state requests which puts the resources back in to
previously requested active state before resuming any CPU. TCSes are
dedicated for each type of requests. Active mode TCSes (AMC) are used to
send requests immediately to the resource, while control TCS are used to
provide specific information to the controller. Sleep and Wake TCS send
sleep and wake requests, after and before the system halt respectively.
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Raju P.L.S.S.S.N <rplsssn@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Recent Raspberry Pi firmware provides a mailbox property to detect
under-voltage conditions. Here is the current definition.
The u32 value returned by the firmware is divided into 2 parts:
- lower 16-bits are the live value
- upper 16-bits are the history or sticky value
Bits:
0: undervoltage
1: arm frequency capped
2: currently throttled
16: undervoltage has occurred
17: arm frequency capped has occurred
18: throttling has occurred
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
This is a branch with a few merge requests that either came in late, or
took a while longer for us to review and merge than usual and thus cut
it a bit close to the merge window. We stage them in a separate branch
and if things look good, we still send them up -- and that's the case
here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface.
-----BEGIN PGP SIGNATURE-----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=RUL0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
The tegra_cpuidle_pcie_irqs_in_use() function is stubbed out for non-ARM
builds, but now we can compile-test the Tegra pci driver on non-Tegra
ARM platforms as well, which results in a new link error:
drivers/pci/host/pci-tegra.o: In function `tegra_pcie_map_irq':
pci-tegra.c:(.text+0x288): undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
drivers/pci/host/pci-tegra.o: In function `tegra_msi_map':
pci-tegra.c:(.text+0xba0): undefined reference to `tegra_cpuidle_pcie_irqs_in_use'
This adapts the #ifdef statement to match the exact condition under which
the function can be called.
Fixes: 51bc085d64 ("PCI: Improve host drivers compile test coverage")
Cc: Rob Herring <robh@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Command DB is a simple database in the shared memory of QCOM SoCs, that
provides information regarding shared resources. Some shared resources
in the SoC have properties that are probed dynamically at boot by the
remote processor. The information pertaining to the SoC and the platform
are made available in the shared memory. Drivers can query this
information using predefined strings.
Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This contains some cleanup of the memory controller driver as well as
unification work to share more code between Tegra20 and later SoC
generations. Also included are an implementation for the hot resets
functionality by the memory controller which is required to properly
reset busy hardware.
-----BEGIN PGP SIGNATURE-----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=uVPT
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.18-memory-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
memory: tegra: Changes for v4.18-rc1
This contains some cleanup of the memory controller driver as well as
unification work to share more code between Tegra20 and later SoC
generations. Also included are an implementation for the hot resets
functionality by the memory controller which is required to properly
reset busy hardware.
* tag 'tegra-for-4.18-memory-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
memory: tegra: Add Tegra210 memory controller hot resets
memory: tegra: Add Tegra124 memory controller hot resets
memory: tegra: Add Tegra114 memory controller hot resets
memory: tegra: Add Tegra30 memory controller hot resets
memory: tegra: Add Tegra20 memory controller hot resets
memory: tegra: Introduce memory client hot reset
memory: tegra: Squash tegra20-mc into common tegra-mc driver
memory: tegra: Remove unused headers inclusions
memory: tegra: Apply interrupts mask per SoC
memory: tegra: Setup interrupts mask before requesting IRQ
memory: tegra: Do not handle spurious interrupts
dt-bindings: memory: tegra: Add hot resets definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to reset busy HW properly, memory controller needs to be
involved, otherwise it is possible to get corrupted memory or hang machine
if HW was reset during DMA. Introduce memory client 'hot reset' that will
be used for resetting of busy HW.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30+ has some minor differences in registers / bits layout compared
to Tegra20. Let's squash Tegra20 driver into the common tegra-mc driver
in a preparation for the upcoming MC hot reset controls implementation,
avoiding code duplication.
Note that this currently doesn't report the value of MC_GART_ERROR_REQ
because it is located within the GART register area and cannot be safely
accessed from the MC driver (this happens to work only by accident). The
proper solution is to integrate the GART driver with the MC driver, much
like is done for the Tegra SMMU, but that is an invasive change and will
be part of a separate patch series.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently we are enabling handling of interrupts specific to Tegra124+
which happen to overlap with previous generations. Let's specify
interrupts mask per SoC generation for consistency and in a preparation
of squashing of Tegra20 driver into the common one that will enable
handling of GART faults which may be undesirable by newer generations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If CONFIG_RASPBERRYPI_FIRMWARE=n:
drivers/gpio/gpio-raspberrypi-exp.c: In function ‘rpi_exp_gpio_get_polarity’:
drivers/gpio/gpio-raspberrypi-exp.c:71: warning: ‘get.polarity’ is used uninitialized in this function
drivers/gpio/gpio-raspberrypi-exp.c: In function ‘rpi_exp_gpio_get_direction’:
drivers/gpio/gpio-raspberrypi-exp.c:150: warning: ‘get.direction’ is used uninitialized in this function
The dummy firmware interface functions return 0, which means success,
causing subsequent code to make use of the never initialized output
parameter.
Fix this by making the dummy functions return an error code (-ENOSYS)
instead.
Note that this assumes the firmware always fills in the requested data
in the CONFIG_RASPBERRYPI_FIRMWARE=y case.
Fixes: d45f1a563b ("staging: vc04_services: fix up rpi firmware functions")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaxiNzAAoJEGCrR//JCVInYhYP/2kPhc5t/kszA1bcklcbO9dY
eX37Ra/RR4yQ5yeQZVIZ4UkUovxk9PmG2tM4K5oJaTDsz5pPEgavVOOr3sbfj6vb
4O9auTeysEQlHcbVdNFum0YS2gUY2YD7D12DTRorotLxCqod184ccWXq0XGfIWaY
l3YRrcL/lPlqmyS3z/GNx9oNygOMUzEfXfIQYICyzHuYiLBUGnkKC1vIb+Hx1TDq
Cxk++AUqH13Mss24O2A2QQh+oBHj2BybDLLqwcC5PSpsUbFrVCfzG54l43mig32T
NOxV0Qnml2wAtU4H0QcgtSgwRimHD0YOiX8ssquvDDiqTqM5G+llSTGkEbYe+AUW
4GIZYoBOwGkfEXS+tyymHe9yfc5h1OLYAeFU1jRm723c7phanuu67rPn35YC8UMK
zSql10JpkAGNzMikrxxb6wnis951w2UFlzhgZQ6ItA/nRq3l+oEQA0Qiljv965nz
DVLsD5+gdhK6GBctkzlsD5HFn6GjM8JilnsOVPHD765nKnVBSxKiXRLV228XVug2
rChF1FhQqLnM54jCMqHZX5fS9SbSgtYswHqIXpVw6GmJkqq/Ly10yGR0vuWD+uyn
BV7q5AKpGrwm6wZkMM2uZ1VdUtWzn856AbkqrvX/QhmJcX4McuqaLUrC8bSOj1ty
KeVil0akq3nU+xHl5Ojs
=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
These changes are rather small, with just a fix for a return value check
and some preparatory work for Tegra194 BPMP support.
-----BEGIN PGP SIGNATURE-----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=oigm
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-firmware' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "firmware: Changes for v4.17-rc1" from Thierry Reding:
These changes are rather small, with just a fix for a return value check
and some preparatory work for Tegra194 BPMP support.
* tag 'tegra-for-4.17-firmware' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
firmware: tegra: adjust tested variable
firmware: tegra: Simplify channel management
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlqlyPEeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGNa0H/RIa/StQuYu/SBwa
JRqQFmkIsx+gG+FyamJrqGzRfyjounES8PbfyaN3cCrzYgeRwMp1U/bZW6/l5tkb
OjTtrCJ6CJaa21fC/7aqn3rhejHciKyk83EinMu5WjDpsQcaF2xKr3SaPa62Ja24
fhawKq3CnUa+OUuAbicVX8yn4viUB6x8FjSN/IWfp3Cs4IBR7SGxxD7A4MET9FbQ
5OOu0al8ly9QeCggTtJyk+cApeLfexEBTbUur9gm7GcH9jhUtJSyZCZsDJx6M2yb
CwdgF4fyk58c1fuHvTFb0AdUns55ba3nicybRHHMVbDpZIG9v4/M1yJETHHf5cD7
t3rFjrY=
=+Ldf
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rc5' into devel
Linux 4.16-rc5 merged into the GPIO devel branch to resolve
a nasty conflict between fixes and devel in the RCAR driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra194 BPMP only implements 5 channels (4 to BPMP, 1 to CCPLEX),
and they are not placed contiguously in memory. The current channel
management in the BPMP driver does not support this.
Simplify and refactor the channel management such that only one atomic
transmit channel and one receive channel are supported, and channels
are not required to be placed contiguously in memory. The same
configuration also works on T186 so we end up with less code.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- MCIP aka ARconnect fixes for SMP builds [Euginey]
- Preventive fix for SLC (L2 cache) flushing [Euginey]
- Kconfig default fix [Ulf Magnusson]
- trailing semicolon fixes [Luis de Bethencourt]
- other assorted minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+Bmc
-----END PGP SIGNATURE-----
Merge tag 'arc-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- MCIP aka ARconnect fixes for SMP builds [Euginey]
- preventive fix for SLC (L2 cache) flushing [Euginey]
- Kconfig default fix [Ulf Magnusson]
- trailing semicolon fixes [Luis de Bethencourt]
- other assorted minor fixes
* tag 'arc-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: setup cpu possible mask according to possible-cpus dts property
ARC: mcip: update MCIP debug mask when the new cpu came online
ARC: mcip: halt GFRC counter when ARC cores halt
ARCv2: boot log: fix HS48 release number
arc: dts: use 'atmel' as manufacturer for at24 in axs10x_mb
ARC: Fix malformed ARC_EMUL_UNALIGNED default
ARC: boot log: Fix trailing semicolon
ARC: dw2 unwind: Fix trailing semicolon
ARC: Enable fatal signals on boot for dev platforms
ARCv2: Don't pretend we may set L-bit in STATUS32 with kflag instruction
ARCv2: cache: fix slc_entire_op: flush only instead of flush-n-inv
As of today we use hardcoded MCIP debug mask, so if we launch
kernel via debugger and kick fever cores than HW has all cpus
hang at the momemt of setup MCIP debug mask.
So update MCIP debug mask when the new cpu came online, instead of
use hardcoded MCIP debug mask.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
In SMP systems, GFRC is used for clocksource. However by default the
counter keeps running even when core is halted (say when debugging via a
JTAG debugger). This confuses Linux timekeeping and triggers flase RCU stall
splat such as below:
| [ARCLinux]# while true; do ./shm_open_23-1.run-test ; done
| Running with 1000 processes for 1000 objects
| hrtimer: interrupt took 485060 ns
|
| create_cnt: 1000
| Running with 1000 processes for 1000 objects
| [ARCLinux]# INFO: rcu_preempt self-detected stall on CPU
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| INFO: rcu_preempt detected stalls on CPUs/tasks:
| 0-...: (1 GPs behind) idle=71e/0/0 softirq=135264/135264 fqs=0
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| 3-...: (1 GPs behind) idle=4e0/0/0 softirq=134304/134304 fqs=0
| (detected by 1, t=13648 jiffies, g=31493, c=31492, q=1)
Starting from ARC HS v3.0 it's possible to tie GFRC to state of up-to 4
ARC cores with help of GFRC's CORE register where we set a mask for
cores which state we need to rely on.
We update cpu mask every time new cpu came online instead of using
hardcoded one or using mask generated from "possible_cpus" as we
want it set correctly even if we run kernel on HW which has fewer cores
than expected (or we launch kernel via debugger and kick fever cores
than HW has)
Note that GFRC halts when all cores have halted and thus relies on
programming of Inter-Core-dEbug register to halt all cores when one
halts.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog]
Add latest firmware property tags from the latest Raspberry Pi downstream
kernel. This is needed for the GPIO tags, so we can control the GPIO
multiplexor lines.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A number of new drivers get added this time, along with many low-priority
bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with
the TEE is added
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yz0k
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
Create SMMU display groups for Tegra30, Tegra114, Tegra124 and Tegra210.
This allows the display controllers on these devices to share the same
IOMMU domain using the standard IOMMU group mechanism.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move Tegra186 support to the consolidated PMC driver to reduce some of
the duplication and also gain I/O pad functionality on the new SoC as a
side-effect.
Signed-off-by: Thierry Reding <treding@nvidia.com>
large change that introduces runtime PM support to the clk framework. Now we
properly call runtime PM operations on the device providing a clk when the clk
is in use. This helps on SoCs where the clks provided by a device need
something to be powered on before using the clks, like power domains or
regulators. It also helps power those things down when clks aren't in use. The
other core change is a devm API addition for clk providers so we can get rid of
a bunch of clk driver remove functions that are just doing
of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and smattering
of non-critical fixes to existing drivers. The biggest diff is support for
Mediatek MT2712 and MT7622 SoCs, but those patches really just add a bunch
of data.
By the way, we're trying something new here where we build the tree up with
topic branches. We plan to work this into our workflow so that we don't step
on each other's toes, and so the fixes branch can be merged on an as-needed
basis.
Core:
- Runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- Runtime PM support for Samsung exynos5433/exynos4412 providers
- Removal of clkdev aliases on Samsung SoCs
- Convert clk-gpio to use gpio descriptors
- Various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- Sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- Support for the second display unit clock on Renesas RZ/G1E
- Suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- New clock ids for Rockchip rk3188 and rk3368 SoCs
- Various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hC7z
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have two changes to the core framework this time around.
The first being a large change that introduces runtime PM support to
the clk framework. Now we properly call runtime PM operations on the
device providing a clk when the clk is in use. This helps on SoCs
where the clks provided by a device need something to be powered on
before using the clks, like power domains or regulators. It also helps
power those things down when clks aren't in use.
The other core change is a devm API addition for clk providers so we
can get rid of a bunch of clk driver remove functions that are just
doing of_clk_del_provider().
Outside of the core, we have the usual addition of clk drivers and
smattering of non-critical fixes to existing drivers. The biggest diff
is support for Mediatek MT2712 and MT7622 SoCs, but those patches
really just add a bunch of data.
By the way, we're trying something new here where we build the tree up
with topic branches. We plan to work this into our workflow so that we
don't step on each other's toes, and so the fixes branch can be merged
on an as-needed basis.
Summary:
Core:
- runtime PM support for clk providers
- devm API for of_clk_add_hw_provider()
New Drivers:
- Mediatek MT2712 and MT7622
- Renesas R-Car V3M SoC
Updates:
- runtime PM support for Samsung exynos5433/exynos4412 providers
- removal of clkdev aliases on Samsung SoCs
- convert clk-gpio to use gpio descriptors
- various driver cleanups to match kernel coding style
- Amlogic Video Processing Unit VPU and VAPB clks
- sigma-delta modulation for Allwinner audio PLLs
- Allwinner A83t Display clks
- support for the second display unit clock on Renesas RZ/G1E
- suspend/resume support for Renesas R-Car Gen3 CPG/MSSR
- new clock ids for Rockchip rk3188 and rk3368 SoCs
- various 'const' markings on clk_ops structures
- RPM clk support on Qualcomm MSM8996/MSM8660 SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: stm32h7: fix test of clock config
clk: pxa: fix building on older compilers
clk: sunxi-ng: a83t: Fix i2c buses bits
clk: ti: dra7-atl-clock: fix child-node lookups
clk: qcom: common: fix legacy board-clock registration
clk: uniphier: fix DAPLL2 clock rate of Pro5
clk: uniphier: fix parent of miodmac clock data
clk: hi3798cv200: correct parent mux clock for 'clk_sdio0_ciu'
clk: hisilicon: Delete an error message for a failed memory allocation in hisi_register_clkgate_sep()
clk: hi3660: fix incorrect uart3 clock freqency
clk: kona-setup: Delete error messages for failed memory allocations
ARC: clk: fix spelling mistake: "configurarion" -> "configuration"
clk: cdce925: remove redundant check for non-null parent_name
clk: versatile: Improve sizeof() usage
clk: versatile: Delete error messages for failed memory allocations
clk: ux500: Improve sizeof() usage
clk: ux500: Delete error messages for failed memory allocations
clk: spear: Delete error messages for failed memory allocations
clk: ti: Delete error messages for failed memory allocations
clk: mmp: Adjust checks for NULL pointers
...
By default, it is assumed that the UTMI clock is generated from a 12 MHz
reference clock (MAINCK). If it's not the case, the FREQ field of the
SFR_UTMICKTRIM has to be updated to generate the UTMI clock in the
proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target of
480 MHz.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Tegra power management firmware running on the co-processor (BPMP)
implements a simple pseudo file system akin to debugfs. The file
system can be used for debugging purposes to examine and change the
status of selected resources controlled by the firmware (such as
clocks, resets, voltages, powergates, ...).
Add support to "mirror" the firmware's file system to debugfs. At
boot, query firmware for a list of all possible files and create
corresponding debugfs entries. Read/write of individual files is
implemented by sending a Message ReQuest (MRQ) that passes the full
file path name and data to firmware via DRAM.
Signed-off-by: Timo Alho <talho@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add static inline stubs to bpmp.h when CONFIG_BPMP is not enabled.
This allows building BPMP-related drivers with COMPILE_TEST.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose and export the tegra_bpmp_mrq_return() function for use by
drivers outside the core BPMP driver. This function is used to reply to
messages originating from the BPMP, which is required in the thermal
driver.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Response messages from Tegra BPMP firmware contain an error return code
as the first word of payload. The error code is used to indicate
incorrectly formatted request message or use of non-existing resource
(clk, reset, powergate) identifier. Current implementation of
tegra_bpmp_transfer() ignores this code and does not pass it to caller.
Fix this by adding an extra struct member to tegra_bpmp_message and
populate that with return code.
Signed-off-by: Timo Alho <talho@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver subsystems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZtdt7AAoJEIwa5zzehBx3EboP/jR2T9lrMavXR1zL48L14yJb
S+fiJlrX1Kr42UF4PQvsfs+uTqOLmycrPVFkMb6IwoUPzQ9UCOSoiMzYm2b7ZPvt
uIesHhdM3/xun6wKfieN8GmNA1yDVynTxo0TTYDw5ha7I6s2GHgw0GSFzy3wm0Qg
KzerAO3gzf3L5XsKR0cai3IXNjHO9ubpFG1ReR09da28nPElP8ggWg0KnqdO76Ch
BGpFj78EC875ZNqwHgnspUqgGDJnBjig3m/uA4FWA0G9Jl38tCyKTZfUR7cEraoV
kyCgBlR/UrI8eXVTyEy5k5iTsQ3A1VhX4rGjyH+5NZHTs1yWr4+RDND/qeGl9tSo
VASuOtH6Rc3vdUDpHPBNAFNQH8fwwDoKf96dvN1tiffsx6LSKb//NyOfkXzKOtR6
CP5raYfX4YktLtHq0XVTZ/6r3XmLcTHzElR/dCFpQOFcTOYii0pWtfcWouahbZ1w
dhoBX/dbNq37MfzrxtHN2VTIEHpn2GU7u+ZGkp2ArokD58BAft/M3Xee1cDnF75g
ZDwe5eNFT8aBZKaY7zwG8cdxiw9kACAivDRwW+zgpfUr39c+d0+QmVfnfJh4EGXK
Ri6yr2EfBWK6jw3cwkdSyyt7iSzIkB+RiuuD1MjpYhWzAvoDpzqkXYukFGbpXnuy
vUFHNuP1ocUsRtCs8mm1
=yBzS
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
The M4U IP blocks in mt2712 is MTK's generation2 M4U which use the
ARM Short-descriptor like mt8173, and most of the HW registers are
the same.
The difference is that there are 2 M4U HWs in mt2712 while there's
only one in mt8173. The purpose of 2 M4U HWs is for balance the
bandwidth.
Normally if there are 2 M4U HWs, there should be 2 iommu domains,
each M4U has a iommu domain.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move this code from arch/arm/mach-tegra and make it common among 32-bit
and 64-bit Tegra SoCs. This is slightly complicated by the fact that on
32-bit Tegra, the SoC device is used as the parent for all devices that
are instantiated from device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
The BPMP firmware, found on Tegra186 and later, provides an ABI that can
be used to enable and disable power to several power partitions in Tegra
SoCs. The ABI allows for enumeration of the available power partitions,
so the driver can be reused on future generations, provided the BPMP ABI
remains stable.
Based on work by Stefan Kristiansson <stefank@nvidia.com> and Mikko
Perttunen <mperttunen@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the BPMP ABI header to a more recent version. The new version
adds support for a new powergating ABI as well as access to the ring
buffer console, which allows debug messages to be output to the BPMP
debug console.
Some of the previously undocumented fields have been documented and
missing bitmasks have been added. Furthermore the MRQ_RESET request
now has a sub-command that allows to determine the maximum ID which
in turn allows the resets to be enumerated, thereby allowing drivers
to become agnostic of the Tegra generation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds support for hdlc-bus mode to the fsl_ucc_hdlc driver. This can
be enabled with the "fsl,hdlc-bus" property in the DTS node of the
corresponding ucc.
This aligns the configuration of the UPSMR and GUMR registers to what is
done in our ucc_hdlc driver (that only support hdlc-bus mode) and with
the QuickEngine's documentation for hdlc-bus mode.
GUMR/SYNL is set to AUTO for the busmode as in this case the CD signal
is ignored. The brkpt_support is enabled to set the HBM1 bit in the
CMXUCR register to configure an open-drain connected HDLC bus.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the bitmask for the two bit SYNL register according to the QUICK
Engine Reference Manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
- rework the Linux page table geometry to lower memory usage on 64-bit Book3S
(IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features on future
firmwares.
- Freescale updates from Scott: "Includes a fix for a powerpc/next mm regression
on 64e, a fix for a kernel hang on 64e when using a debugger inside a
relocated kernel, a qman fix, and misc qe improvements."
Thanks to:
Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong, Nicholas Piggin, Roy
Pledge, Scott Wood, Valentin Longchamp.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YOQs
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
Driver updates for ARM SoCs.
* Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
* PATA driver for Palmchip BK371 (acked by Tejun)
* Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
* PMC support for Tegra186
* SoC detection support for Renesas RZ/G1H and RZ/G1N
* Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
* Misc smaller tweaks for other platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=B43K
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs:
Reset subsystem, merged through arm-soc by tradition:
- Make bool drivers explicitly non-modular
- New support for i.MX7 and Arria10 reset controllers
PATA driver for Palmchip BK371 (acked by Tejun)
Power domain drivers for i.MX (GPC, GPCv2)
- Moved out of mach-imx for GPC
- Bunch of tweaks, fixes, etc
PMC support for Tegra186
SoC detection support for Renesas RZ/G1H and RZ/G1N
Move Tegra flow controller driver from mach directory to drivers/soc
- (Power management / CPU power driver)
Misc smaller tweaks for other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
soc: pm-domain: Fix the mangled urls
soc: renesas: rcar-sysc: Add support for R-Car H3 ES2.0
soc: renesas: rcar-sysc: Add support for fixing up power area tables
soc: renesas: Register SoC device early
soc: imx: gpc: add workaround for i.MX6QP to the GPC PD driver
dt-bindings: imx-gpc: add i.MX6 QuadPlus compatible
soc: imx: gpc: add defines for domain index
soc: imx: Add GPCv2 power gating driver
dt-bindings: Add GPCv2 power gating driver
ARM/clk: move the ICST library to drivers/clk
ARM: plat-versatile: remove stale clock header
ARM: keystone: Drop PM domain support for k2g
soc: ti: Add ti_sci_pm_domains driver
dt-bindings: Add TI SCI PM Domains
PM / Domains: Do not check if simple providers have phandle cells
PM / Domains: Add generic data pointer to genpd data struct
soc/tegra: Add initial flowctrl support for Tegra132/210
soc/tegra: flowctrl: Add basic platform driver
soc/tegra: Move Tegra flowctrl driver
ARM: tegra: Remove unnecessary inclusion of flowctrl header
...
immrbar_virt_to_phys() is not used anymore
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Li Yang <pku.leo@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Since commit 5093bb965a ("powerpc/QE: switch to the cpm_muram
implementation"), muram area is not part of immrbar mapping anymore
so immrbar_virt_to_phys() is not usable anymore.
Fixes: 5093bb965a ("powerpc/QE: switch to the cpm_muram implementation")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Li Yang <pku.leo@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The flowctrl driver is required for both ARM and ARM64 Tegra devices
and in order to enable support for it for ARM64, move the Tegra flowctrl
driver into drivers/soc/tegra.
By moving the flowctrl driver, tegra_flowctrl_init() is now called by
via an early initcall and to prevent this function from attempting to
mapping IO space for a non-Tegra device, a test for 'soc_is_tegra()'
is also added.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With the new Tegra186 PMC driver merged, anything that relies on the previous
PMC driver fails to link when that is disabled:
arch/arm/mach-tegra/pm.o: In function `tegra_pm_set':
pm.c:(.text.tegra_pm_set+0x3c): undefined reference to `tegra_pmc_enter_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_suspend_enter':
pm.c:(.text.tegra_suspend_enter+0x4): undefined reference to `tegra_pmc_get_suspend_mode'
arch/arm/mach-tegra/pm.o: In function `tegra_init_suspend':
pm.c:(.init.text+0x1c): undefined reference to `tegra_pmc_get_suspend_mode'
pm.c:(.init.text+0x74): undefined reference to `tegra_pmc_set_suspend_mode'
ERROR: tegra_powergate_sequence_power_up [drivers/ata/ahci_tegra.ko] undefined!
ERROR: tegra_powergate_power_off [drivers/ata/ahci_tegra.ko] undefined!
Making the definition depend on the presence of the driver makes it build
again, though that might not be the correct fix.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 854014236290 ("soc/tegra: Implement Tegra186 PMC support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A few other things need to be added in soc/qman, such that
caam/qi won't open-code them.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Export qman_query_fq_np() function and related structures.
This will be needed in the caam/qi driver, where "queue empty"
condition will be decided based on the frm_cnt.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add and export the ID of the channel serviced by the
CAAM (Cryptographic Acceleration and Assurance Module) DCP.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since qman_volatile_dequeue() is already exported, move the related
structures into the public header too.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WPBu
-----END PGP SIGNATURE-----
Merge tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
* tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-*] ARC_HAS_COH_CACHES no longer relevant
ARCv2: intc: Delete useless comments in Device Trees
ARCv2: IDU-intc: Delete deprecated parameters in Device Trees
ARCv2: IDU-intc: mask all common interrupts by default
ARCv2: IDU-intc: Use build registers for getting numbers of interrupts
ARCv2: intc: Set default priority for all core interrupts
ARCv2: intc: Use runtime value of irq count for setting up intc
ARCv2: intc: Rework the build time irq count information
ARC: [intc-*]: confine NR_CPU_IRQS to intc code
ARCv2: intc: Use ARC_REG_STATUS32 for addressing STATUS32 reg
arc: vdk: Add support of UIO
arc: vdk: Add support of MMC controller
arc: vdk: Disable halt on reset
This enhancement is needed to allow masking all available common interrupts
in IDU interrupt controller in boot time since the kernel can
discover a number of them from the build register. Also now there
is no need to specify in device tree a list of used core interrupts
by IDU. E.g. before:
idu_intc: idu-interrupt-controller {
compatible = "snps,archs-idu-intc";
interrupt-controller;
interrupt-parent = <&core_intc>;
#interrupt-cells = <2>;
interrupts = <24 25 26 27 28 29 30 31>;
};
and after:
idu_intc: idu-interrupt-controller {
compatible = "snps,archs-idu-intc";
interrupt-controller;
interrupt-parent = <&core_intc>;
#interrupt-cells = <2>;
};
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The Atmel MPDDR controller support LPDDR2 and LPDDR3 memories, add their
types.
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for secure and
trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and store
them as relative offsets to save space in the kernel image & memory.
- Allow building the kernel with thin archives, which should allow us to build
an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the kernel endian
from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9 Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage support,
qbman fixes/cleanup, device tree updates, and some misc cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman Khandual,
Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz, Christophe Jaillet,
Christophe Leroy, Denis Kirjanov, Elimar Riesebieter, Frederic Barrat,
Gautham R. Shenoy, Geliang Tang, Geoff Levand, Jack Miller, Johan Hovold,
Lars-Peter Clausen, Libin, Madhavan Srinivasan, Michael Neuling, Nathan
Fontenot, Naveen N. Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin,
Rashmica Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xOzf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights include:
- Support for the kexec_file_load() syscall, which is a prereq for
secure and trusted boot.
- Prevent kernel execution of userspace on P9 Radix (similar to
SMEP/PXN).
- Sort the exception tables at build time, to save time at boot, and
store them as relative offsets to save space in the kernel image &
memory.
- Allow building the kernel with thin archives, which should allow us
to build an allyesconfig once some other fixes land.
- Build fixes to allow us to correctly rebuild when changing the
kernel endian from big to little or vice versa.
- Plumbing so that we can avoid doing a full mm TLB flush on P9
Radix.
- Initial stack protector support (-fstack-protector).
- Support for dumping the radix (aka. Linux) and hash page tables via
debugfs.
- Fix an oops in cxl coredump generation when cxl_get_fd() is used.
- Freescale updates from Scott: "Highlights include 8xx hugepage
support, qbman fixes/cleanup, device tree updates, and some misc
cleanup."
- Many and varied fixes and minor enhancements as always.
Thanks to:
Alexey Kardashevskiy, Andrew Donnellan, Aneesh Kumar K.V, Anshuman
Khandual, Anton Blanchard, Balbir Singh, Bartlomiej Zolnierkiewicz,
Christophe Jaillet, Christophe Leroy, Denis Kirjanov, Elimar
Riesebieter, Frederic Barrat, Gautham R. Shenoy, Geliang Tang, Geoff
Levand, Jack Miller, Johan Hovold, Lars-Peter Clausen, Libin,
Madhavan Srinivasan, Michael Neuling, Nathan Fontenot, Naveen N.
Rao, Nicholas Piggin, Pan Xinhui, Peter Senna Tschudin, Rashmica
Gupta, Rui Teng, Russell Currey, Scott Wood, Simon Guo, Suraj
Jitindar Singh, Thiago Jung Bauermann, Tobias Klauser, Vaibhav Jain"
[ And thanks to Michael, who took time off from a new baby to get this
pull request done. - Linus ]
* tag 'powerpc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (174 commits)
powerpc/fsl/dts: add FMan node for t1042d4rdb
powerpc/fsl/dts: add sg_2500_aqr105_phy4 alias on t1024rdb
powerpc/fsl/dts: add QMan and BMan nodes on t1024
powerpc/fsl/dts: add QMan and BMan nodes on t1023
soc/fsl/qman: test: use DEFINE_SPINLOCK()
powerpc/fsl-lbc: use DEFINE_SPINLOCK()
powerpc/8xx: Implement support of hugepages
powerpc: get hugetlbpage handling more generic
powerpc: port 64 bits pgtable_cache to 32 bits
powerpc/boot: Request no dynamic linker for boot wrapper
soc/fsl/bman: Use resource_size instead of computation
soc/fsl/qe: use builtin_platform_driver
powerpc/fsl_pmc: use builtin_platform_driver
powerpc/83xx/suspend: use builtin_platform_driver
powerpc/ftrace: Fix the comments for ftrace_modify_code
powerpc/perf: macros for power9 format encoding
powerpc/perf: power9 raw event format encoding
powerpc/perf: update attribute_group data structure
powerpc/perf: factor out the event format field
powerpc/mm/iommu, vfio/spapr: Put pages on VFIO container shutdown
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip
it is running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system controller
- A new checking module for the ARM "PSCI" (not to be confused
with "SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their
power management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra
bpmp interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates.
Conflicts:
- ARCH_RENESAS now selects SOC_BUS, but no longer needs GPIOLIB
- drivers/soc/renesas/Makefile: multiple files got added, keep
all in logical sorting
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6dP8
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- A new driver for the power management controller on TI Keystone
- Support for the prerelease "SCPI" firmware protocol that ended up
being shipped by Amlogic in their GXBB SoC.
- A soc_device can now be matched using a glob from inside the
kernel, when another driver wants to know the specific chip it is
running on and cannot find out from DT, firmware or hardware.
- Renesas SoCs now support identification through the soc_device
interface, both in user space and kernel.
- Renesas r8a7743 and r8a7745 gain support for their system
controller
- A new checking module for the ARM "PSCI" (not to be confused with
"SCPI" mentioned above) firmware interface.
- A new driver for the Tegra GMI memory interface
- Support for the Tegra firmware interfaces with their power
management controllers
As usual, the updates for the reset controller framework are merged
here, as they tend to touch multiple SoCs as well, including a new
driver for the Oxford (now Broadcom) OX820 chip and the Tegra bpmp
interface.
The existing drivers for Atmel, Qualcomm, NVIDIA, TI Davinci, and
Rockchips SoCs see some further updates"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
misc: sram: remove useless #ifdef
drivers: psci: Allow PSCI node to be disabled
drivers: psci: PSCI checker module
soc: renesas: Identify SoC and register with the SoC bus
firmware: qcom: scm: Return PTR_ERR when devm_clk_get fails
firmware: qcom: scm: Remove core, iface and bus clocks dependency
dt-bindings: firmware: scm: Add MSM8996 DT bindings
memory: da8xx-ddrctl: drop the call to of_flat_dt_get_machine_name()
bus: da8xx-mstpri: drop the call to of_flat_dt_get_machine_name()
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: rcar-sysc: add R8A7745 support
reset: Add Tegra BPMP reset driver
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
mailbox: tegra-hsp: Use after free in tegra_hsp_remove_doorbells()
mailbox: Add Tegra HSP driver
firmware: arm_scpi: add support for pre-v1.0 SCPI compatible
...
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Hlx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"These are mostly timer/clocksource driver updates which were
Reviewed/Acked by Daniel but had to be merged via ARC tree due to
dependencies.
I will follow up with another pull request with actual ARC changes
early next week !
Summary:
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]"
* tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: axs10x: really enable ARC PGU
ARC: rename Zebu platform support to HAPS
clocksource: nps: avoid maybe-uninitialized warning
clocksource: Add clockevent support to NPS400 driver
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
soc: Support for NPS HW scheduling
clocksource: import ARC timer driver
ARC: breakout timer include code into separate header ...
ARC: move mcip.h into include/soc and adjust the includes
ARC: breakout aux handling into a separate header
ARC: time: move time_init() out of the driver
ARC: timer: gfrc, rtc: build under same option (64-bit timers)
ARC: timer: gfrc, rtc: Read BCR to detect whether hardware exists ...
ARC: timer: gfrc, rtc: deuglify big endian code
This new header file is for NPS400 SoC (part of ARC architecture).
The header file includes macros for save/restore of HW scheduling.
The control of HW scheduling is achieved by writing core registers.
This code was moved from arc/plat-eznps so it can be used
from drivers/clocksource/, available only for CONFIG_EZNPS_MTM_EXT.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Also remove the dependency on ARCv2, to increase compile coverage for
!ARCV2 builds
Acked-by: Daniel Lezcano <daniel.lezcnao@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC timers use aux registers for programming and this paves way for
moving ARC timer drivers into drivers/clocksource
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The hardware descriptors have big endian (BE) format.
Provide proper endianness handling for the remaining
descriptor fields, to ensure they are correctly
accessed by non-BE CPUs too.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
There are multiple occurences of both contextB and context_b
in different h/w descriptors, referring to the same descriptor
field known as "Context B". Stick with the "context_b" naming,
for obvious reasons including consistency (see also context_a).
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Preventively mask every access to the 'fqid' h/w field,
since it is defined as a 24-bit field, for every h/w
descriptor. Add generic accessors for this field to
ensure correct access.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This contains mostly cleanup and new feature work on the power
management controller as well as the addition of a Kconfig symbol for
the new Tegra186 (Parker) SoC generation.
-----BEGIN PGP SIGNATURE-----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=yvrl
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
soc: tegra: Core SoC changes for v4.10-rc1
This contains mostly cleanup and new feature work on the power
management controller as well as the addition of a Kconfig symbol for
the new Tegra186 (Parker) SoC generation.
* tag 'tegra-for-4.10-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Use consistent naming for PM domains
soc/tegra: pmc: Remove genpd when adding provider fails
soc/tegra: pmc: Check return code for pm_genpd_init()
soc/tegra: pmc: Clean-up I/O rail error messages
soc/tegra: pmc: Simplify IO rail bit handling
soc/tegra: pmc: Guard against uninitialised PMC clock
soc/tegra: pmc: Add I/O pad voltage support
soc/tegra: pmc: Use consistent ordering of bit definitions
soc/tegra: pmc: Correct type of variable for tegra_pmc_readl()
soc/tegra: pmc: Use BIT macro for register field definition
Signed-off-by: Olof Johansson <olof@lixom.net>
IVC is an inter-processor communication protocol that uses shared memory
to exchange data between processors. The BPMP driver makes use of this
to communicate with the Boot and Power Management Processor (BPMP) and
uses an additional hardware synchronization primitive from the HSP block
to signal availability of new data (doorbell).
Firmware running on the BPMP implements a number of services such as the
control of clocks and resets within the system, or the ability to ungate
or gate power partitions.
-----BEGIN PGP SIGNATURE-----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=9jQK
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
firmware: Add Tegra IVC and BPMP support
IVC is an inter-processor communication protocol that uses shared memory
to exchange data between processors. The BPMP driver makes use of this
to communicate with the Boot and Power Management Processor (BPMP) and
uses an additional hardware synchronization primitive from the HSP block
to signal availability of new data (doorbell).
Firmware running on the BPMP implements a number of services such as the
control of clocks and resets within the system, or the ability to ungate
or gate power partitions.
* tag 'tegra-for-4.10-firmware' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: firmware: Allow child nodes inside the Tegra BPMP
dt-bindings: Add power domains to Tegra BPMP firmware
firmware: tegra: Add BPMP support
firmware: tegra: Add IVC library
dt-bindings: firmware: Add bindings for Tegra BPMP
Signed-off-by: Olof Johansson <olof@lixom.net>
The Boot and Power Management Processor (BPMP) is a co-processor found
on Tegra SoCs. It is designed to handle the early stages of the boot
process and offload power management tasks (such as clocks, resets,
powergates, ...) as well as system control services.
Compared to the ARM SCPI, the services provided by BPMP are message-
based rather than method-based. The BPMP firmware driver provides the
services to transmit data to and receive data from the BPMP. Users can
also register a Message ReQuest (MRQ), for which a service routine will
be run when a corresponding event is received from the firmware.
A set of messages, called the BPMP ABI, are specified for a number of
different services provided by the BPMP (such as clocks or resets).
Based on work by Sivaram Nair <sivaramn@nvidia.com> and Joseph Lo
<josephl@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Inter-VM communication (IVC) is a communication protocol which is
designed for interprocessor communication (IPC) or the communication
between the hypervisor and the virtual machine with a guest OS.
Message channels are used to communicate between processors. They are
backed by DRAM or SRAM, so care must be taken to maintain coherence of
data.
The IVC library maintains memory-based descriptors for the transmission
and reception channels as well as the data coherence of the counter and
payload. Clients, such as the driver for the BPMP firmware, can use the
library to exchange messages with remote processors.
Based on work by Peter Newman <pnewman@nvidia.com> and Joseph Lo
<josephl@nvidia.com>.
Signed-off-by: Thierry Reding <treding@nvidia.com>
I/O pins on Tegra SoCs are grouped into so-called I/O pads. Each such
pad can be used to control the common voltage signal level and power
state of the pins in the given pad.
I/O pads can be powered down even if the system is active, which can
save power from that I/O interface. For SoC generations prior to
Tegra124 the I/O pad voltage is automatically detected and hence the
system software doesn't need to configure it. However, starting with
Tegra210 the detection logic has been removed, so explicit control of
the I/O pad voltage by system software is required.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The raspberrypi-firmware.h file should provide empty functions if we
aren't building in that option. This makes it easier to test-build
code, and not have odd warnings about unused variables if you just try
to #define away the functions.
Cc: Daniel Stone <daniels@collabora.com>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: popcornmix <popcornmix@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This comes from the downstream tree and is needed for the new VCHIQ
driver in staging.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
that weren't causing enough problems (or any problems when we're just
clarifying things) to warrant sending outside the merge window. The
majority of changes are in drivers for various SoCs. Full details
are in the logs, but here's the summary.
Core:
- Better support for DeviceTree overlays with the addition of the
CLK_OF_DECLARE_DRIVER macro. Now we won't probe a clk driver
for a device node that matched during of_clk_init(), unless
the driver uses CLK_OF_DECLARE_DRIVER instead of CLK_OF_DECLARE.
This allows overlays to work cleanly for drivers that must probe
before the device model is ready, and also after it's ready
when an overlay is loaded.
- Clarification in the code around how clk_hw pointers are returned
from of clk providers
- Proper migration of prepare/enable counts to parents when the
clk tree is constructed
New Drivers:
- Socionext's UniPhier SoCs
- Loongson1C
- ZTE ZX296718
- Qualcomm MDM9615
- Amlogic GXBB AO clocks and resets
- Broadcom BCM53573 ILP
- Maxim MAX77620
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver (A31, A31s,
A23 and A33)
- Exynos 5xxx audio and DRAM clks
- Loongson1B AC97, DMA and NAND clks
- Rockchip DDR clks and rk3399 driver tweaks
- Renesas R-Car M3-W (r8a7796) SoC SDHI interface and Watchdog timer clks
- Renasas R-Car H3 and M3-W CMT clks and RAVB+Thermal clks for M3-W
- Amlogic GXBB MMC gate clks
- at91 sama5d4 sckc
- Removal of STiH415 and STiH416 clk support as the SoC is being removed
- Rework of STiH4xx clk support for new style bindings
- Continuation of driver migration to clk_hw based registration APIs
- xgene PMD support
- bcm2835 critical clk markings
- ARM versatile ICST
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=NFUB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk framework updates from Stephen Boyd:
"The core clk framework changes are small again. They're mostly minor
fixes that weren't causing enough problems (or any problems when we're
just clarifying things) to warrant sending outside the merge window.
The majority of changes are in drivers for various SoCs. Full details
are in the logs, but here's the summary.
Core:
- Better support for DeviceTree overlays with the addition of the
CLK_OF_DECLARE_DRIVER macro. Now we won't probe a clk driver for a
device node that matched during of_clk_init(), unless the driver
uses CLK_OF_DECLARE_DRIVER instead of CLK_OF_DECLARE. This allows
overlays to work cleanly for drivers that must probe before the
device model is ready, and also after it's ready when an overlay is
loaded.
- Clarification in the code around how clk_hw pointers are returned
from of clk providers
- Proper migration of prepare/enable counts to parents when the clk
tree is constructed
New Drivers:
- Socionext's UniPhier SoCs
- Loongson1C
- ZTE ZX296718
- Qualcomm MDM9615
- Amlogic GXBB AO clocks and resets
- Broadcom BCM53573 ILP
- Maxim MAX77620
Updates:
- Four Allwinner SoCs are migrated to the new style clk driver (A31,
A31s, A23 and A33)
- Exynos 5xxx audio and DRAM clks
- Loongson1B AC97, DMA and NAND clks
- Rockchip DDR clks and rk3399 driver tweaks
- Renesas R-Car M3-W (r8a7796) SoC SDHI interface and Watchdog timer
clks
- Renasas R-Car H3 and M3-W CMT clks and RAVB+Thermal clks for M3-W
- Amlogic GXBB MMC gate clks
- at91 sama5d4 sckc
- Removal of STiH415 and STiH416 clk support as the SoC is being
removed
- Rework of STiH4xx clk support for new style bindings
- Continuation of driver migration to clk_hw based registration APIs
- xgene PMD support
- bcm2835 critical clk markings
- ARM versatile ICST"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (199 commits)
CLK: Add Loongson1C clock support
clk: Loongson1: Make use of GENMASK
clk: Loongson1: Update clocks of Loongson1B
clk: Loongson1: Refactor Loongson1 clock
clk: change the type of clk_hw_onecell_data.num to unsigned int
clk: zx296718: register driver earlier with core_initcall
clk: mvebu: dynamically allocate resources in Armada CP110 system controller
clk: mvebu: fix setting unwanted flags in CP110 gate clock
clk: nxp: clk-lpc32xx: Unmap region obtained by of_iomap
clk: mediatek: clk-mt8173: Unmap region obtained by of_iomap
clk: sunxi-ng: Fix reset offset for the A23 and A33
clk: at91: sckc: optimize boot time
clk: at91: Add sama5d4 sckc support
clk: at91: move slow clock controller clocks to sckc.c
clk: imx6: initialize GPU clocks
clk: imx6: fix i.MX6DL clock tree to reflect reality
clk: imx53: Add clocks configuration
clk: uniphier: add clock data for UniPhier SoCs
clk: uniphier: add core support code for UniPhier clock driver
clk: bcm: Add driver for BCM53573 ILP clock
...
This driver enables the Freescale DPAA 1.x Queue Manager block.
QMan is a hardware accelerator that manages frame queues. It allows
CPUs and other accelerators connected to the SoC datapath to enqueue
and dequeue ethernet frames, thus providing the infrastructure for
data exchange among CPUs and datapath accelerators.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This driver enables the Freescale DPAA 1.x Buffer Manager block.
BMan is a hardware accelerator that manages buffer pools. It allows
CPUs and other accelerators connected to the SoC datapath to acquire
and release buffers during data processing.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Add a header for the SIP interface defined to access the dcf controller
handling ddr rate changes on rk3399 (and most likely later socs).
This interface is shared between the clock driver as well as the
devfreq driver.
The SIP interface counterpart was merged from pull-request #684 [0]
into the upstream arm-trusted-firmware codebase.
[0] https://github.com/ARM-software/arm-trusted-firmware/pull/684
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The usb controller does not manage correctly the suspend mode for
the ehci. In echi mode, there is no way to suspend without any
device connected to it. This is why this specific control is added
to fix this issue. Since the suspend mode works in ohci mode, this
specific control works by suspend the usb controller in ohci mode.
This specific control is by setting the SUSPEND_A/B/C fields of
SFR_OHCIICR(OHCI Interrupt Configuration Register) in the SFR
while the OHCI USB suspend.
This set operation must be done before the USB clock disabled,
clear operation after the USB clock enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
