IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
For the trip points, I used values from the BSP code.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (85°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220517013607.2252-4-qianfanguijin@163.com
OPP table value is get from allwinner lichee linux-3.10 kernel driver
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220517013607.2252-3-qianfanguijin@163.com
The CPU of sun8i-r40 is powered by PMIC, let's add "cpu-supply" node.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220517013607.2252-2-qianfanguijin@163.com
Universal Serial Interface (USI) supports three types of serial interface
such as Universal Asynchronous Receiver and Transmitter (UART), Serial
Peripheral Interface (SPI), and Inter-Integrated Circuit (I2C).
Each protocols can be working independently and configured as one of
those using external configuration inputs.
Exynos Auto v9 SoC support 12 USIs. When a USI uses two pins such as i2c
and 3 wire uarts(RX/TX only), we can use remain two pins as i2c mode.
So, we can define one USI node that includes serial/spi and hsi2c.
usi_i2c nodes can be used only for i2c mode.
We can have below combinations for one USI.
1) The usi node is used either 4 pin uart or 4 pin spi
-> No usi_i2c can be used
2) The usi node is used 2 pin uart(RX/TX) and i2c(SDA/SCL)
-> usi_i2c should be enabled to use the latter i2c
3) The usi node is used i2c(SDA/SCL) and i2c(SDA/SCL)
-> usi_i2c should be enabled to use the latter i2c
By default, all USIs are initially set to uart mode by below setting.
samsung,mode = <USI_V2_UART>;
You can change it either USI_V2_SPI or USI_V2_I2C.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220701015226.32781-6-chanho61.park@samsung.com
Before adding whole USI nodes, this applies the changes of usi0 in
advance. To be the usi0 and serian_0 nodes as SoC default, some
properties should be moved to exynosautov9-sadk.dts.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220701015226.32781-5-chanho61.park@samsung.com
Add samsung,exynosautov9-usi dedicated compatible for representing USI
of Exynos Auto v9 SoC.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220701015226.32781-2-chanho61.park@samsung.com
They should be started with "gpp5-".
Fixes: 31bbac5263aa ("arm64: dts: exynos: add initial support for exynosautov9 SoC")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627005832.8709-1-chanho61.park@samsung.com
Add DT bindings for ST MIPID02 and DCMI to Avenger96 base DT.
Both the ST MIPID02 and DCMI are disabled by default, as the
AV96 camera module is optional.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for RCC pin, this is used on AV96 board
for e.g. sensor clock supply.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for DCMI pins, this is used on AV96 board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add DT compatible string for DH electronics STM32MP15xx DHCOR on DRC Compact
carrier board into YAML DT binding document. This system is a general purpose
DIN Rail Controller design.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Those pin comments refer to SPI2 pins, not SPI1 pins, update the comments.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Add UDPHS (the USB High Speed Device Port controller) support.
The both lan966x SOCs (LAN9662 and LAN9668) have the same UDPHS
IP. This IP is also the same as the one present in the SAMA5D3
SOC.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220704102845.168438-4-herve.codina@bootlin.com
The USB device controller available in the Microchip LAN9662 SOC
is the same IP as the one present in the SAMA5D3 SOC.
Add the LAN9662 compatible string and set the SAMA5D3 compatible
string as a fallback for the LAN9662.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220704102845.168438-3-herve.codina@bootlin.com
Enables Reset and Clocks Controller on STM32MP13
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Like for stm32mp15, when stm32 RCC node is used to interact with a secure
context (using clock SCMI protocol), a different path has to be used for
yaml verification.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Rob Herring <robh@kernel.org>
According to the OSD32MP1 Power System overview[1] the EEPROM is connected to
the VDD line and not to some single-purpose fixed regulator.
Set the EEPROM supply according to the diagram to eliminate this parent-less
regulator.
[1]: https://octavosystems.com/app_notes/osd32mp1-power-system-overview/#connections
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
According to the OSD32MP1 Power System overview[1] ldo3's input is always
internally connected to vdd_ddr.
[1]: https://octavosystems.com/app_notes/osd32mp1-power-system-overview/#connections
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment. No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The stm32 ipcc mailbox driver supports only two interrupts (rx and tx), so
remove the unsupported "wakeup" one.
Note that the EXTI interrupt 61 has two roles : it is hierarchically linked
to the GIC IPCC "rx" interrupt, and it acts as a wakeup source.
Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
"status" does not match any pattern in the gpio-leds binding. Rename the
node to the preferred pattern. This fixes a `make dtbs_check` error.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220702132816.46456-1-samuel@sholland.org
The USBH composed of EHCI and OHCI controllers needs the PHY clock to be
initialized first, before enabling (gating) them. The reverse is also
required when going to suspend.
So, add USBPHY clock as 1st entry in both controllers, so the USBPHY PLL
gets enabled 1st upon controller init. Upon suspend/resume, this also makes
the clock to be disabled/re-enabled in the correct order.
This fixes some IRQ storm conditions seen when going to low-power, due to
PHY PLL being disabled before all clocks are cleanly gated.
Fixes: 949a0c0dec85 ("ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c")
Fixes: db7be2cb87ae ("ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Delete the node fixed clock managed by secure world with SCMI.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
LSE clock is provided by SCMI.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
The peripheral clock of CEC is not LSE but CEC.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fixes stm32mp15*-scmi DTS files introduced in [1] to also access PWR
regulators through SCMI service. This is needed since enabling secure
only access to RCC clock and reset controllers also enables secure
access only on PWR voltage regulators reg11, reg18 and usb33 hence
these must also be accessed through SCMI Voltage Domain protocol.
This change applies on commit [2] that already corrects issues from
commit [1].
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Link: [1] https://lore.kernel.org/linux-arm-kernel/20220422150952.20587-7-alexandre.torgue@foss.st.com
Link: [2] https://lore.kernel.org/linux-arm-kernel/20220613071920.5463-1-alexandre.torgue@foss.st.com
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Use generic name for reset controller of AT91 devices to comply with
DT specifications.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220610092414.1816571-2-claudiu.beznea@microchip.com
Fix the following compilation warning:
arch/arm/boot/dts/sama5d2.dtsi:371.29-382.6: Warning
(avoid_unnecessary_addr_size): /ahb/apb/ethernet@f8008000:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
also defined at arch/arm/boot/dts/at91-sama5d2_icp.dts:353.8-363.3
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220615080633.1881196-2-claudiu.beznea@microchip.com
