IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Use correct compatible according to dt-binding.
Fixes + few other lines of `make qcom/sdm845-oneplus-fajita.dtb`:
arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dt.yaml: qfprom@784000: compatible: ['qcom,qfprom'] is too short
From schema: Documentation/devicetree/bindings/nvmem/qcom,qfprom.yaml
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213190228.106924-1-david@ixit.cz
Downstream defines four ADC channels related to thermal sensors external
to the PM8998 and two channels for internal voltage measurements.
Add these to the upstream SDM845 MTP, describe the thermal monitor
channels and add thermal_zones for these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-5-bjorn.andersson@linaro.org
Add a node for the ADC Thermal Monitor found in the PM8998 PMIC. This is
used to connect thermal zones with ADC channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211005032531.2251928-4-bjorn.andersson@linaro.org
Property #stream-id-cells is legacy leftover and isn't currently
documented nor used.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211208184707.100716-1-david@ixit.cz
v5.16-rc1 + 20211207114003.100693-2-vkoul@kernel.org
The immutable branch contains DT binding and in defines for the global
clock controller registers used the the Qualcomm SM8450 dtsi.
This reverts commit ed9500c1df.
The clock-frequency property was meant to aid platforms with broken firmwares
that don't set up the timer properly on their own. Don't include it where it is
not the case.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211202004328.459899-1-konrad.dybcio@somainline.org
Currently Soundcard has 1 rx device for headset and SoundWire Speaker Playback.
This setup has issues, ex if we try to play on headset the audio stream is
also sent to SoundWire Speakers and we will hear sound in both headsets and speakers.
Make a separate device for Speakers and Headset so that the streams are
different and handled properly.
Fixes: 45021d35fc ("arm64: dts: qcom: c630: Enable audio support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211209175342.20386-2-srinivas.kandagatla@linaro.org
The msm-id and board-id can be used to select the correct dtb when
multiple are provided to the bootloader.
Multiple DTBs can be provided on sdm845 devices using boot image header
v1 by appending them all to the kernel image before creating the boot
image. The bootloader then selects them like this:
Best match DTB tags 321/00000008/0x00000000/20001/20014/20115/20018/0/(offset)0x79998E27/(size)0x000173CD
Using pmic info 0x20014/0x20115/0x20018/0x0 for device 0x20014/0x20115/0x20018/0x0
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211209225938.2427342-1-caleb.connolly@linaro.org
Add device tree bindings for global clock controller on SM8450 SoCs.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211207114003.100693-2-vkoul@kernel.org
Enable the remoteprocs found on the SoC and add a qcom,rmtfs-mem node.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082208.21492-9-luca.weiss@fairphone.com
Add the required nodes for booting the CDSP on sm6350.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082208.21492-8-luca.weiss@fairphone.com
Add the required nodes for booting the ADSP on sm6350.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082208.21492-6-luca.weiss@fairphone.com
Add the required nodes for booting the MPSS on sm6350.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082208.21492-4-luca.weiss@fairphone.com
Sort clocks and interrupts as specified in the docs and remove the stray
property #power-domain-cells from aoss_qmp to solve dtbs_check
validation errors.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211213082614.22651-11-luca.weiss@fairphone.com
Samsung J5 2015 is a MSM8916 based Smartphone. It is similar to some of the
other MSM8916 devices, especially the Samsung ones.
With this patch initial support for the following is added:
- eMMC/SD card
- Buttons
- USB (although no suiting MUIC driver currently)
- UART (untested for lack of equipment)
- WiFi/Bluetooth (WCNSS)
It is worth noting that Samsung J5 with MSM8916 exists in different
generations (e.g Samsung J5 2015 and Samsung J5 2016) which each have
different models (e.g. samsung-j5nlte, samsung-j5xnlte, etc). This patch
is only regarding the 2015 generation, but should work with all of it's
models, as far as we could test.
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Julian Ribbeck <julian.ribbeck@gmx.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211116200734.73920-1-julian.ribbeck@gmx.de
Change sdhcN aliases to mmcN to make them actually work. Currently the
board uses non-standard aliases sdhcN, which do not work, resulting in
mmc0 and mmc1 hosts randomly changing indices between boots.
Fixes: c4da5a5616 ("arm64: dts: qcom: Add msm8916 sdhci configuration nodes")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211201020559.1611890-1-dmitry.baryshkov@linaro.org
The IDP2 and CRD boards share the EC and H1 parts, so define
all related device nodes into a common file and include them
in the idp2 and crd dts files to avoid duplication.
Signed-off-by: Kshitiz Godara <kgodara@codeaurora.org>
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1638185497-26477-4-git-send-email-quic_rjendra@quicinc.com
CRD (Compute Reference Design) is a sc7280 based board, largely
derived from the existing IDP board design with some key deltas
1. has EC and H1 over SPI similar to IDP2
2. touchscreen and trackpad support
3. eDP display
We just add the barebones dts file here, subsequent patches will
add support for EC/H1 and other components.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1638185497-26477-3-git-send-email-quic_rjendra@quicinc.com
Document the qcom,sc7280-crd board based off sc7280 SoC,
The board is also known as hoglin in the Chrome OS builds,
so document the google,hoglin compatible as well.
Signed-off-by: Rajendra Nayak <quic_rjendra@quicinc.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1638185497-26477-2-git-send-email-quic_rjendra@quicinc.com
This property doesn't seem to exist in the documentation nor
in source code, but for some reason it is defined in a bunch
of device trees.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211123162436.1507341-1-danct12@riseup.net
MSM8916 is similar to the other SoCs that had the RPM stats node added
in commit 290bc68465 ("arm64: dts: qcom: Enable RPM Sleep stats").
However, the dynamic offset readable at 0x14 seems only available on
some of the newer firmware versions. To be absolutely sure, make use
of the new qcom,msm8916-rpm-stats compatible that reads the sleep stats
from a fixed offset of 0xdba0.
Statistics are available for a "vmin" and "xosd" low power mode:
$ cat /sys/kernel/debug/qcom_stats/vmin
Count: 0
Last Entered At: 0
Last Exited At: 0
Accumulated Duration: 0
Client Votes: 0x0
$ cat /sys/kernel/debug/qcom_stats/xosd
Count: 0
Last Entered At: 0
Last Exited At: 0
Accumulated Duration: 0
Client Votes: 0x0
Cc: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211119213953.31970-4-stephan@gerhold.net
Enable and configure DWC3 and QUSB2 PHY to enable USB
functionality on the Redmi Note 7.
Signed-off-by: Alexey Min <alexey.min@gmail.com>
Co-developed-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-9-danct12@riseup.net
This lets the user sees the framebuffer console.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-8-danct12@riseup.net
This enables the volume down key as well as the power button.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-5-danct12@riseup.net
Add most of the RPM PM660/PM660L regulators and the fixed ones,
defining the common electrical part of this platform.
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-4-danct12@riseup.net
It's not worth duplicating the same node over and over again,
so let's keep the common bits in the pm660 DTSI, making only
changing the status and keycode necessary.
Also, disable RESIN/PWR by default just in case if there are
devices that doesn't use them.
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Reviewed-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-3-danct12@riseup.net
This makes eMMC/SD device number consistent.
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Dang Huynh <danct12@riseup.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211120214227.779742-2-danct12@riseup.net
When powering up the ps8640, we need to deassert PD right
after we turn on the vdd33 regulator. Unfortunately, the vdd33
regulator takes some time (~4ms) to turn on. Add in the delay
for the vdd33 regulator so that when the driver deasserts PD
that the regulator has had time to ramp.
Signed-off-by: yangcong <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211115030155.9395-1-yangcong5@huaqin.corp-partner.google.com
Based on current driver availability, add either nodes or comments regarding
peripherals connected via I2C/SPI.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-14-konrad.dybcio@somainline.org
Add support for SONY Xperia 1 III (PDX215) and 5 III (PDX214) smartphones.
Both are based on the SM8350 Sagami platform and feature some really high-end
specs, such as:
- 4K (1 III / PRO-I) / 1080p (5 III), 120Hz HDR OLED 10-bit panels
- USB-C 3.1 with HDMI in (yes, phone as display!) and DP out
- 5G
- 8 or 12 gigs of ram, 128/256/512 gigs of storage
- A 3.5mm headphone jack, a RGB notification LED and a uSD card slot :)
- IP65/68 dust/water resistance
- Dual front-firing speakers and a lot of microphones
- Crazy complex camera hardware (especially on the PRO-I), which includes
4 cameras, an RGBIR sensor and a 3D iToF
The aforementioned PRO-I (PDX217) is not supported in this patch, because
even though it shares most of the code with 1 III, nobody really has it (yet?)
This only adds basic support for booting to a USB shell with a
bootloader-enabled display, support for all the awesome hardware listed above
will (hopefully) come (hopefully) soon.
In order to get a working boot image, you need to run (e.g. for 1 III):
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/sm8350-sony-xperia-\
sagami-pdx215.dtb > .Image.gz-dtb
mkbootimg \
--kernel .Image.gz-dtb \
--ramdisk some_initrd.img \
--pagesize 4096 \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--tags_offset 0x100 \
--cmdline "SOME_CMDLINE" \
--dtb_offset 0x1f00000 \
--header_version 1 \
--os_version 11 \
--os_patch_level 2021-10 \ # or newer
-o boot.img-sony-xperia-pdx215
Then, you need to flash it on the device and get rid of all the
vendor_boot/dtbo mess:
fastboot flash boot boot.img-sony-xperia-pdx215
fastboot erase vendor_boot
fastboot flash dtbo emptydtbo.img
fastboot reboot
Where emptydtbo.img is a tiny file that consists of 2 bytes (all zeroes), doing
a "fastboot erase" won't cut it, the bootloader will go crazy and things will
fall apart when it tries to overlay random bytes from an empty partition onto a
perfectly good appended DTB.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-13-konrad.dybcio@somainline.org
Add all the clock names that the GCC driver expects to get via DT, so that the
clock handles can be filled as the development progresses.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-8-konrad.dybcio@somainline.org
Disable PON/RESIN keys by default and keep the RESIN keycode set-per-board, as
these settings are not common between devices (one cannot even assume all
devices have buttons nowadays..).
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-7-konrad.dybcio@somainline.org
Thermal zone names should not be longer than 20 names, which is indicated by
a message at boot. Change "camera-thermal-bottom" to "cam-thermal-bottom" to
fix it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211114012755.112226-6-konrad.dybcio@somainline.org
