IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-65-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-64-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-63-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-62-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-61-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-60-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-59-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-58-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-57-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-56-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-55-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-54-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-53-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-52-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-51-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-50-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-49-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-47-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-46-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-45-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-44-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-43-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-42-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-41-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from William Qiu <william.qiu@starfivetech.com>:
This patchset adds initial rudimentary support for the StarFive
Quad SPI controller driver. And this driver will be used in
StarFive's VisionFive 2 board.The first patch constrain
minItems/maxItems of resets for JH7110 QSPI and Patch 2 adds
support for StarFive JH7110 QSPI.
Merge series from Mark Brown <broonie@kernel.org>:
This series opens up build coverage of a bunch of SPI drivers by
allowing build under COMPILE_TEST where possible, while also adding
appropriate architecture specific dependencies to a couple of drivers
that didn't have them so they don't show up in builds when they're not
useful. We also have one fix for the dependencies of the s3c24xx driver
which was turned up in the process of doing this.
Merge series from Rob Herring <robh@kernel.org>:
This started as just removing open coded parsing and address translation
of "reg", and ended up with cleaning up the probe functions to use
modern, preferred APIs for driver probe.
It is compile tested only.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-38-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-37-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-36-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-35-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-34-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-33-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-32-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-31-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-30-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-29-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-28-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-27-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-26-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230303172041.2103336-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20230303172041.2103336-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230303172041.2103336-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
variable slave in spi_alloc_master() or spi_alloc_slave()
has been assigned. it is not necessary to be assigned again
Signed-off-by: Lizhe <sensor1010@163.com>
Link: https://lore.kernel.org/r/20230226063334.7489-1-sensor1010@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
spi_pcpu_stats_totalize() is a rather large macro, and is instantiated
28 times, causing a large amount of duplication in the amount of
generated code.
Reduce the duplication by replacing spi_pcpu_stats_totalize() by a real
C function, and absorb all other common code from
spi_statistics_##name##_show(). As (a) the old "field" parameter was
the name of a structure member, which cannot be passed to a function,
and (b) passing a pointer to the member is also not an option, due to
the loop over all possible CPUs, the "field" parameter is replaced by an
"offset" parameter, pointing to a location within the structure.
This reduces kernel size by ca. 4 KiB (on arm32 and arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cb7690d9d04c06eec23dbb98fbb5444082125cff.1677594432.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build time dependency on the Qualcomm platform support so add
an || COMPILE_TEST so we've got better build coverage of the driver.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230221-spi-arch-deps-v1-6-83d1566474cf@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build time dependency on the platform support so add an
|| COMPILE_TEST so we've got better build coverage of the driver.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230221-spi-arch-deps-v1-5-83d1566474cf@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no build time dependency on the DaVicni or Keystone architecture
support so add an || COMPILE_TEST so we've got better build coverage of the
driver.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230221-spi-arch-deps-v1-4-83d1566474cf@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the NXP Flex SPI driver has a dependency on ARCH_LAYERSCAPE ||
HAS_IOMEM which means that the dependency is almost always true and the
driver available. Really these should be two separate dependencies, with
an || COMPILE_TEST dependency for the architecture to ensure build coverage
is maintained.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230221-spi-arch-deps-v1-3-83d1566474cf@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
If base support for Rockchip SoCs has been disabled then the SPI driver
won't be terribly useful, add a dependency on ARCH_ROCKCHIP || COMPILE_TEST
to avoid it appearing when not needed.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20230221-spi-arch-deps-v1-2-83d1566474cf@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc52xx-psc and mpc512x-psc drivers use DT property parsing
functions for 'reg' and 'interrupts', but those are available as
platform device resources. Convert probe functions to use them and
simplify probe to a single function. For 'cell-index', also use the
preferred typed property function.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230217-dt-mpc5xxx-spi-v1-3-3be8602fce1e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the mpc52xx-psc and mpc512x-psc drivers to use the managed
devres variants of functions in probe. Also use dev_err_probe() as
appropriate. With this, the error handling can be simplified.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230217-dt-mpc5xxx-spi-v1-2-3be8602fce1e@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add QSPI reset operation in device probe and add RISCV support to
QUAD SPI Kconfig.
Co-developed-by: Ziv Xu <ziv.xu@starfivetech.com>
Signed-off-by: Ziv Xu <ziv.xu@starfivetech.com>
Signed-off-by: William Qiu <william.qiu@starfivetech.com>
Link: https://lore.kernel.org/r/20230302105221.197421-3-william.qiu@starfivetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A small set of fixes for SPI drivers, Krishna has been doing a bunch of
work on Tegra210 QuadSPI and found a bunch of issues there and there's
a couple of small fixes for other drivers too.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmP/tqQACgkQJNaLcl1U
h9Da0wf/Up72MjOEo6JHplNrvuT6P2SxA/9l3KABp7h3MM+otsxGPlfgMlcKSVty
cQd07cFY1PS4asxLKguIQq+qEG8aseRJkfgWXxPXBXmhVrg/oz5IcDc7sLRHLCaz
2Y/G8qwsT3EWBTQc+LRA+LdpdYglGRmcTRbeMclTyVOY/dS5lFTQv84pWfrG4waV
9UBbYs6tuci15dPSf/hsTCdmo/rAlyxozJpkMCVDq89NvzPUQ6UyEDmrpWuR6Gnf
lhbRPhTgivBRSBDRiIs4l9Cjo4zC4qp0ytMy8wm/PBhgiN+Bz23TlLK9ldISDbHh
iVvp+WEH3f67sK9p/VpOJ/mY9rtumA==
=2QLL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small set of fixes for SPI drivers, Krishna has been doing a bunch
of work on Tegra210 QuadSPI and found a bunch of issues there and
there's a couple of small fixes for other drivers too"
* tag 'spi-fix-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: tegra210-quad: Fix iterator outside loop
spi: tegra210-quad: Fix validate combined sequence
spi: tegra210-quad: set half duplex flag
spi: spi-sn-f-ospi: fix duplicate flag while assigning to mode_bits
spi: cadence-quadspi: Fix cancel the indirect read mask
As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv
-----BEGIN PGP SIGNATURE-----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=p6Xp
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/itAw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykJbQCfWv/J4ZElO108iHBU5mJCDagUDBgAnAtLLN6A
SEAnnokGCDtA/BNIXeES
=luRi
-----END PGP SIGNATURE-----
Merge tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of serial and tty driver updates for 6.3-rc1.
Once again, Jiri and Ilpo have done a number of core vt and tty/serial
layer cleanups that were much needed and appreciated. Other than that,
it's just a bunch of little tty/serial driver updates:
- qcom-geni-serial driver updates
- liteuart driver updates
- hvcs driver cleanups
- n_gsm updates and additions for new features
- more 8250 device support added
- fpga/dfl update and additions
- imx serial driver updates
- fsl_lpuart updates
- other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (143 commits)
tty: n_gsm: add keep alive support
serial: imx: remove a redundant check
dt-bindings: serial: snps-dw-apb-uart: add dma & dma-names properties
soc: qcom: geni-se: Move qcom-geni-se.h to linux/soc/qcom/geni-se.h
tty: n_gsm: add TIOCMIWAIT support
tty: n_gsm: add RING/CD control support
tty: n_gsm: mark unusable ioctl structure fields accordingly
serial: imx: get rid of registers shadowing
serial: imx: refine local variables in rxint()
serial: imx: stop using USR2 in FIFO reading loop
serial: imx: remove redundant USR2 read from FIFO reading loop
serial: imx: do not break from FIFO reading loop prematurely
serial: imx: do not sysrq broken chars
serial: imx: work-around for hardware RX flood
serial: imx: factor-out common code to imx_uart_soft_reset()
serial: 8250_pci1xxxx: Add power management functions to quad-uart driver
serial: 8250_pci1xxxx: Add RS485 support to quad-uart driver
serial: 8250_pci1xxxx: Add driver for quad-uart support
serial: 8250_pci: Add serial8250_pci_setup_port definition in 8250_pcilib.c
tty: pcn_uart: fix memory leak with using debugfs_lookup()
...
Check for non dma transfers that do not fit in FIFO has issue and skips
combined sequence for Tegra234 & Tegra241 which does not have GPCDMA.
Fixes: 1b8342cc4a ("spi: tegra210-quad: combined sequence mode")
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20230224164034.56933-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to cancel the indirect read transfer process,
so should be use CQSPI_REG_INDIRECTRD_CANCEL_MASK
Signed-off-by: Hongbin Ji <jhb_ee@163.com>
Link: https://lore.kernel.org/r/20230222092128.4237-1-jhb_ee@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been a fairly quiet release for SPI, though it is likely that
the next release will have some big changes as there's some preparatory
work for multiple chip select support gone in - the rest of the code is
on the list but will need to be rebased onto -rc1. Otherwise there's a couple
of new tunables for chip select timings, some new devices and smaller
device specific updates and fixes.
- Support for configuring the hold and minimum inactive times for chip
selects.
- Beginnings of support for supporting devices which have multiple chip
selects on a single device.
- Support for newer Broadcom HSSPI and Intel controllers, Silicon Labs
EM3581 and SI3210.
There is a simple add/add conflict in MAINTAINERS with the I2C tree.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmPzcwwACgkQJNaLcl1U
h9B3egf/Yo9cnaB473bDfIOmx/AAKU33U059n27CKdbkOy/pqP7zTaurne0aTFDD
SsJh9+Akmb4aBQTTT8RRn9zLho6pX2lUrtFDKjbVB1DM/E7Bad8EsMlqBGLpGUNs
GmEsa99XtUlcEeORq3HIObZ2G2v+Jy0IiidCUyTo48JZBAV3pvI5J8SPUwpWMfqM
fq2U5kCXjxlheQsa4FLzMqnWS91D3H58XFboPQJ2y29sqWSq2OnD/mt9XQVHcvbg
zzL/EfOYoIpw8c9Qf2ZPoLDzRZAdVhugFoMRKccW8OD/v5Rfaf02vhtwfz3G7JpV
So+eEIVSJniavgpBMnUY4tqTOxDe/g==
=xz0n
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been a fairly quiet release for SPI, though it is likely that
the next release will have some big changes as there's some
preparatory work for multiple chip select support gone in - the rest
of the code is on the list but will need to be rebased onto -rc1.
Otherwise there's a couple of new tunables for chip select timings,
some new devices and smaller device specific updates and fixes.
- Support for configuring the hold and minimum inactive times for
chip selects.
- Beginnings of support for supporting devices which have multiple
chip selects on a single device.
- Support for newer Broadcom HSSPI and Intel controllers, Silicon
Labs EM3581 and SI3210"
* tag 'spi-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (67 commits)
spi: dt-bindings: qcom,spi-qcom-qspi: document OPP and power-domains
spi: spidev: drop the incorrect notice from Kconfig
spi: bcm63xx-hsspi: fix error code in probe
spi: bcmbca-hsspi: Fix error code in probe() function
spi: synquacer: Fix timeout handling in synquacer_spi_transfer_one()
spi: intel: Check number of chip selects after reading the descriptor
spi: xilinx: add force_irq for QSPI mode
spi: spi-st-ssc: convert to DT schema
spi: Reorder fields in 'struct spi_transfer'
spi: cadence-quadspi: use STIG mode for small reads
spi: cadence-quadspi: setup ADDR Bits in cmd reads
spi: cadence-quadspi: Add flag for direct mode writes
spi: cadence-quadspi: Reset CMD_CTRL Reg on cmd r/w completion
MAINTAINERS: Remove file reference for Broadcom Broadband SoC HS SPI driver entry
spi: bcm63xx-hsspi: bcmbca-hsspi: fix _be16 type usage
MAINTAINERS: Add entry for Broadcom Broadband SoC HS SPI drivers
spi: bcmbca-hsspi: Add driver for newer HSSPI controller
spi: bcm63xx-hsspi: Disable spi mem dual io read op support
spi: spi-mem: Allow controller supporting mem_ops without exec_op
spi: bcm63xx-hsspi: Add prepend mode support
...
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
One more last minute patch for v6.2 updating the parsing of the
newly added spi-cs-setup-delay-ns - it's been pointed out that
due to the way DT parsing works the change in property size is
ABI visible so let's not let a release go out without it being
fixed. The change got split from some earlier ABI related fixes
to the property since the first version sent had a build error.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmPuWgoACgkQJNaLcl1U
h9AI/gf/SEQzjI4vkoIezfwUfgzeP7Cjphna2rAmOOFc+S871FHUne7csWiNS3DI
YGhr3x2VqKdPyxkM+YoOavH9B9SmF9MUFtiT7Q5MEp0Pb7TQzw23qjrKBrKde0yX
r5cETkhy+21Tk6hzMs/0cC/4zRcf7IjgDT9L9+To9mKDHCYKoj3/WHoES6JgTYa8
z8fApLvjvCx2432eLzm66CoXgSK+UnQKT2bdo2w+YcITPBqge6REhmcfnOT9MzDO
LPOZ2hJ4lM6SPW2a4yBMX4pIouluDd6/giQ8LBt7xjesIKVmiHoW0dXRNis4+gq/
6kVjABEsBQ/xBOFgbuq1WfGRxaVJVA==
=qTWJ
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.2-rc8-abi' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"One more last minute patch for v6.2 updating the parsing of the newly
added spi-cs-setup-delay-ns.
It's been pointed out that due to the way DT parsing works the change
in property size is ABI visible so let's not let a release go out
without it being fixed. The change got split from some earlier ABI
related fixes to the property since the first version sent had a build
error"
* tag 'spi-v6.2-rc8-abi' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Use a 32-bit DT property for spi-cs-setup-delay-ns
The spidev interface has been de-facto stable for many years. This notice
has been unchanged since 2007 and is incorrect so remove it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230216123014.110541-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
This code accidentally returns success instead of a negative error code.
Fixes: a38a2233f2 ("spi: bcmbca-hsspi: Add driver for newer HSSPI controller")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/Y+zmrNJ9zjNQpzWq@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
wait_for_completion_timeout() never returns a <0 value. It returns either
on timeout or a positive value (at least 1, or number of jiffies left
till timeout)
So, fix the error handling path and return -ETIMEDOUT should a timeout
occur.
Fixes: b0823ee35c ("spi: Add spi driver for Socionext SynQuacer platform")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/c2040bf3cfa201fd8890cfab14fa5a701ffeca14.1676466072.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
The flash decriptor contains the number of flash components that we use
to figure out how many flash chips there are connected. Therefore we
need to read it first before deciding how many chip selects the
controller has.
Reported-by: Marcin Witkowski <marcin.witkowski@intel.com>
Fixes: 3f03c618be ("spi: intel: Add support for second flash chip")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230215110040.42186-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Dhruva Gole <d-gole@ti.com>:
* Reset the CMD_CTRL Register, without which read/writes in STIG mode
were failing in some cases. The issue came to light while using STIG
Mode for small reads.
* Also add a flag that can allow us to do direct reads but distinguish
direct writes, thus enabling us to disable writes in DAC mode in some
cases that require it. (Like to write to some connected Flash registers)
* Fix register reads in STIG mode and also use STIG mode while reading flash
registers.
Currently if you try to read a register while in STIG mode there is no
support for ADDR and thus naturally a register never gets read from the
flash.
This patch series has been tested on a TI AM625-SK-EVM with both a quad
spi nor flash (s25hs) and OSPI NOR Flash (s28hs).
Output of ltp-ddt test, "DD_RW_ERASESIZE_UBIFS" run with s25hs512t flash:
...
[ 2.334068] spi-nor spi0.0: s25hs512t (65536 Kbytes)
[ 2.339185] 7 fixed-partitions partitions found on MTD device
fc40000.spi.0
[ 2.346158] Creating 7 MTD partitions on "fc40000.spi.0":
[ 2.351555] 0x000000000000-0x000000080000 : "ospi.tiboot3"
[ 2.358344] 0x000000080000-0x000000280000 : "ospi.tispl"
[ 2.364788] 0x000000280000-0x000000680000 : "ospi.u-boot"
[ 2.371311] 0x000000680000-0x0000006c0000 : "ospi.env"
[ 2.377519] 0x0000006c0000-0x000000700000 : "ospi.env.backup"
[ 2.384419] 0x000000800000-0x000003fc0000 : "ospi.rootfs"
[ 2.390890] 0x000003fc0000-0x000004000000 : "ospi.phypattern"
..snip..
Test Start Time: Wed Jan 11 21:14:31 2023
-----------------------------------------
Testcase Result Exit Value
-------- ------ ----------
OSPI_S_FUNC_DD_RW_ERASESIZE_UBIFS PASS 0
-----------------------------------------------
Total Tests: 1
Total Skipped Tests: 0
Total Failures: 0
Kernel Version: 6.2.0-rc1-00040-g700d796a94e0-dirty
Machine Architecture: aarch64
Hostname: am62xx-evm
Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size from 144 to 128 bytes.
Turn 'timestamped' into a bitfield so that it can be easily merged with
some other bifields and move 'error'.
This should have no real impact on memory allocation because 'struct
spi_transfer' is mostly used on stack, but it can save a few cycles
when the structure is initialized or copied.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/93a051da85a895bc6003aedfb00a13e1c2fc6338.1676370870.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the issue where some flash chips like cypress S25HS256T return the
value of the same register over and over in DAC mode.
For example in the TI K3-AM62x Processors refer [0] Technical Reference
Manual there is a layer of digital logic in front of the QSPI/OSPI
Drive when used in DAC mode. This is part of the Flash Subsystem (FSS)
which provides access to external Flash devices.
The FSS0_0_SYSCONFIG Register (Offset = 4h) has a BIT Field for
OSPI_32B_DISABLE_MODE which has a Reset value = 0. This means, OSPI 32bit
mode enabled by default.
Thus, by default controller operates in 32 bit mode causing it to always
align all data to 4 bytes from a 4byte aligned address. In some flash
chips like cypress for example if we try to read some regs in DAC mode
then it keeps sending the value of the first register that was requested
and inorder to read the next reg, we have to stop and re-initiate a new
transaction.
This causes wrong register values to be read than what is desired when
registers are read in DAC mode. Hence if the data.nbytes is very less
then prefer STIG mode for such small reads.
[0] https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-5-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setup the Addr bit field while issuing register reads in STIG mode. This
is needed for example flashes like cypress define in their transaction
table that to read any register there is 1 cmd byte and a few more address
bytes trailing the cmd byte. Absence of addr bytes will obviously fail
to read correct data from flash register that maybe requested by flash
driver because the controller doesn't even specify which address of the
flash register the read is being requested from.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-4-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Create new flag inorder to avoid playing with use_direct_mode
flag currently being used throughout the driver.
Disable DAC write if auto polling is disabled or CQSPI_DISABLE_DAC_MODE
is set.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-3-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If one leaves the CQSPI_REG_CMDCTRL in an unclean state this may cause
issues in future command reads. This issue came to light when some flash
reads in STIG mode were coming back dirty.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230125081023.1573712-2-d-gole@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sparse tool report warnings: drivers/spi/spi-bcm63xx-hsspi.c:197:31:
sparse: sparse: cast from restricted __be16.
The controller requires big endian 16 bit data. Define an intermediate
u16 value and use __be16 piointer dereferncing for the data to avoid
directly casting to u16 and sparse warning.
Fixes: 85a84a6169 ("spi: bcm63xx-hsspi: Endianness fix for ARM based SoC")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202302110438.sQwQnU54-lkp@intel.com/
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230211032759.72967-1-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The newer BCMBCA SoCs such as BCM6756, BCM4912 and BCM6855 include an
updated SPI controller that add the capability to allow the driver to
control chip select explicitly. Driver can control and keep cs low
between the transfers natively. Hence the dummy cs workaround or prepend
mode found in the bcm63xx-hsspi driver are no longer needed and this new
driver is much cleaner.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-15-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In general the controller supports SPI dual mode operation but the
particular SPI flash dual io read op switches from single mode in cmd
phase to dual mode in address and data phase. This is not compatible
with prepend operation where cmd and address are sent out through the
prepend buffer and they must use same the number of io pins.
This patch disables these SPI flash dual io read ops through the mem_ops
supports_op interface. This makes sure the SPI flash driver selects the
compatible read ops at run time.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-14-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently exec_op is always required if controller driver provides
mem_ops. But some controller such as bcm63xx-hsspi may only need to
implement other operation like supports_op and use the default
execution operation. This patch removes this restriction.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-13-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the controller limitation to keep the chip select low during the
bus idle time between the transfer, a dummy cs workaround was used when
this driver was first upstreamed to the kernel. It basically picks the
dummy cs as !actual_cs so typically dummy cs is 1 when most of the case
only cs 0 is used in the board design. Then invert the polarity of both
cs and tell the controller to start the transfers using dummy cs.
Assuming both cs are active low before the inversion, effectively this
keeps dummy cs high and actual cs low during the transfer and workaround
the issue.
This workaround implies that dummy cs 1 pin has to be set to chip
selection function in the pinmux when the transfer clock is above
25MHz. The old chips likely have default pinmux set to chip select on
the dummy cs pin so it works but this is not case for the new Broadband
BCA chips and this workaround stop working. This is specifically an
issue to support SPI NAND and SPI NOR flash because these flash devices
can typically run at or above 100MHz.
This patch utilizes the prepend feature of the controller to combine the
multiple transfers in the same message to a single transfer when
possible. This way there is no need to keep clock low between transfers
and solve the issue without any hardware requirement.
Multiple transfers within a SPI message may be combined into one
transfer if the following are all true:
* One or more half duplex write transfer in single bit mode
* Optional full duplex read/write at the end
* No delay and cs_change between transfers
Most of the SPI device meets this requirements such as SPI NOR,
SPI NAND flash, Broadcom SPI voice card and etc. For any SPI message
that does not meet the above requirement to combine the transfers, we
switch to original dummy cs mode but limit the clock rate to the safe
25MHz. This is the default auto transfer mode and it makes sure all the
SPI message can be supported automatically under the hood.
This patch also adds the driver sysfs node xfer_mode to provide
the option for overriding the default auto mode and force it to dummy cs
or prepend mode.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-12-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.
This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.
Fixes: 142168eba9 ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-11-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The kernel SPI interface includes the cs_change flag that alters how
the CS behaves.
If we're in the middle of transfers, it tells us to unselect the
CS momentarily since the target device requires that.
If we're at the end of a transfer, it tells us to keep the CS
selected, perhaps because the next transfer is likely targeted
to the same device.
We implement this scheme in the HSSPI driver in this change.
Prior to this change, the CS would toggle momentarily if cs_change
was set for the last transfer. This can be ignored by some or
most devices, but the Microchip TPM2 device does not ignore it.
With the change, the behavior is corrected and the 'glitch' is
eliminated.
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-10-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For SPI controller that implements transfer_one_message, it needs to
insert the delay that required by cs change event between the transfers.
Add a wrapper for the local function _spi_transfer_cs_change_delay_exec
and export it for SPI controller driver to use.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230209200246.141520-9-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern intel hardware uses controllers that work in hardware
sequencing mode. In this mode, the controller exposes a subset
of operations, like read, write and erase, making it easier
and less error-prone for use.
On the other hand, most of the controllers handled by the
platform driver use software sequencing that exposes the
entire set of operations i.e. exposes the low level SPI-NOR
opcodes to the software for use.
Update PCI and Platform help text with this information.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230210164158.211065-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Xiangsheng Hou <xiangsheng.hou@mediatek.com>:
This patch series split from bellow series which pick-up spi relevant patches
https://lore.kernel.org/all/20230130030656.12127-1-xiangsheng.hou@mediatek.com.
This series add MediaTek MT7986 SPI NAND controller support, add read latch
latency, smaple delay adjust and add optional nfi_hclk.
Add snfi sample delay and read latency adjustment which can get
from dts property.
Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230201020921.26712-5-xiangsheng.hou@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add optional nfi_hclk which is needed for MT7986.
Signed-off-by: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230201020921.26712-3-xiangsheng.hou@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Polling mode provides better throughput in general by avoiding the
interrupt overhead as the maximum data size one interrupt can handle is
only 512 bytes. So switch to polling mode as the default mode but add
a driver sysfs option wait_mode to allow user manually changing the mode
at run time between interrupt and polling. Also add driver banner
message when the driver is loaded successfully.
When test on a Broadcom BCM47622(ARM A7 dual core) reference board with
WINBOND W25N01GV SPI NAND chip at 100MHz SPI clock using the MTD speed
test suite, it shows about 15% improvement on the write and 30% on
the read:
** Interrupt mode **
mtd_speedtest: MTD device: 0 count: 16
mtd_speedtest: MTD device size 134217728, eraseblock size 131072, page
size 2048, count of eraseblocks 1024, pages per eraseblock 64, OOB size
64
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 16 eraseblocks, 0 are bad
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 3072 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 6690 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 3066 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 6762 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 3071 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 6772 KiB/s
** Polling mode **
mtd_speedtest: MTD device: 0 count: 16
mtd_speedtest: MTD device size 134217728, eraseblock size 131072, page
size 2048, count of eraseblocks 1024, pages per eraseblock 64, OOB size
64
mtd_test: scanning for bad eraseblocks
mtd_test: scanned 16 eraseblocks, 0 are bad
mtd_speedtest: testing eraseblock write speed
mtd_speedtest: eraseblock write speed is 3542 KiB/s
mtd_speedtest: testing eraseblock read speed
mtd_speedtest: eraseblock read speed is 8825 KiB/s
mtd_speedtest: testing page write speed
mtd_speedtest: page write speed is 3563 KiB/s
mtd_speedtest: testing page read speed
mtd_speedtest: page read speed is 8787 KiB/s
mtd_speedtest: testing 2 page write speed
mtd_speedtest: 2 page write speed is 3572 KiB/s
mtd_speedtest: testing 2 page read speed
mtd_speedtest: 2 page read speed is 8806 KiB/s
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230207065826.285013-8-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HSSPI controller uses big endian for the opcode in the message to the
controller ping pong buffer. Use cpu_to_be16 to properly handle the
endianness for both big and little endian host.
Fixes: 142168eba9 ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230207065826.285013-7-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
New compatible string brcm,bcmbca-hsspi-v1.0 is introduced based on dts
document brcm,bcm63xx-hsspi.yaml. Add it to the driver to support this
new binding.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Link: https://lore.kernel.org/r/20230207065826.285013-6-william.zhang@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move include/linux/qcom-geni-se.h to include/linux/soc/qcom/geni-se.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Acked-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Link: https://lore.kernel.org/r/20230203210133.3552796-1-quic_eberman@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modern CPUs exposes this controller as PCI device that only uses
hardware sequencing capabilities which is safer than software
sequencing.
Leave the platform driver as *DANGEROUS* and update help text since
most of these controllers are using software sequencing.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230206183143.75274-2-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This unlocks twice due to a merge issue.
Fixes: 35bba23e67 ("Merge remote-tracking branch 'spi/for-6.2' into spi-6.2")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/Y+ETCk7XKfAy8yWQ@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Device IDs to the module table for the following controllers:
- 9da4 Cannon Lake 300 Series On-Package
- a2a4 200 Series/Z370 Chipset Family SPI Controller
- 9d24 Intel® 200 Series Chipset Family (Including Intel® X299),
Intel® Z370 Intel® H310C,B365,
also Intel® B460 and H410 Chipset Platform Controller Hub
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230201205455.550308-3-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some private data fields have to change from bxt_info to cnl_info.
Here is the list of Device IDs with the respective documentation taken for
validation:
0xa0a4 - Intel® 500 Series Chipset Family On-Package PCH
0x02a4 - Intel® 400 Series Chipset Family On-Package PCH
0x06a4 - Intel® 400 Series Chipset Family Platform Controller Hub
0x34a4 - Intel® 495 Chipset Family On-Package
0xa3a4 - Intel® B460 and H410 Chipset
According to documentation Broxton controller type has five PR registers.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230201205455.550308-2-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
In preparation for supporting devices with multiple chip selects add an
interface for accessing the chip selects via a function.
Supporting multi-cs in spi core and spi controller drivers would require
the chip_select & cs_gpiod members of struct spi_device to be an array.
But changing the type of these members to array would break the spi driver
functionality. To make the transition smoother introduced four new APIs to
get/set the spi->chip_select & spi->cs_gpiod and replaced all
spi->chip_select and spi->cs_gpiod references in spi core with the API
calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119185342.2093323-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Selecting a symbol with additional dependencies requires
adding the same dependency here:
WARNING: unmet direct dependencies detected for MUX_MMIO
Depends on [n]: MULTIPLEXER [=y] && OF [=n]
Selected by [y]:
- SPI_DW_BT1 [=y] && SPI [=y] && SPI_MASTER [=y] && SPI_DESIGNWARE [=y] && (MIPS_BAIKAL_T1 || COMPILE_TEST [=y])
Drop the 'select' here to avoid the problem. Anyone using
the dw-bt1 SPI driver should make sure they include the
mux driver as well now.
Fixes: 7218838109 ("spi: dw-bt1: Fix undefined devm_mux_control_get symbol")
Fixes: abf0090753 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Link: https://lore.kernel.org/all/20221218192523.c6vnfo26ua6xqf26@mobilestation/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20230130140156.3620863-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When calling spidev_message() from the one of the ioctl() callbacks, the
spi_lock is already taken. When we then end up calling spidev_sync(), we
get the following splat:
[ 214.047619]
[ 214.049198] ============================================
[ 214.054533] WARNING: possible recursive locking detected
[ 214.059858] 6.2.0-rc3-0.0.0-devel+git.97ec4d559d93 #1 Not tainted
[ 214.065969] --------------------------------------------
[ 214.071290] spidev_test/1454 is trying to acquire lock:
[ 214.076530] c4925dbc (&spidev->spi_lock){+.+.}-{3:3}, at: spidev_ioctl+0x8e0/0xab8
[ 214.084164]
[ 214.084164] but task is already holding lock:
[ 214.090007] c4925dbc (&spidev->spi_lock){+.+.}-{3:3}, at: spidev_ioctl+0x44/0xab8
[ 214.097537]
[ 214.097537] other info that might help us debug this:
[ 214.104075] Possible unsafe locking scenario:
[ 214.104075]
[ 214.110004] CPU0
[ 214.112461] ----
[ 214.114916] lock(&spidev->spi_lock);
[ 214.118687] lock(&spidev->spi_lock);
[ 214.122457]
[ 214.122457] *** DEADLOCK ***
[ 214.122457]
[ 214.128386] May be due to missing lock nesting notation
[ 214.128386]
[ 214.135183] 2 locks held by spidev_test/1454:
[ 214.139553] #0: c4925dbc (&spidev->spi_lock){+.+.}-{3:3}, at: spidev_ioctl+0x44/0xab8
[ 214.147524] #1: c4925e14 (&spidev->buf_lock){+.+.}-{3:3}, at: spidev_ioctl+0x70/0xab8
[ 214.155493]
[ 214.155493] stack backtrace:
[ 214.159861] CPU: 0 PID: 1454 Comm: spidev_test Not tainted 6.2.0-rc3-0.0.0-devel+git.97ec4d559d93 #1
[ 214.169012] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 214.175555] unwind_backtrace from show_stack+0x10/0x14
[ 214.180819] show_stack from dump_stack_lvl+0x60/0x90
[ 214.185900] dump_stack_lvl from __lock_acquire+0x874/0x2858
[ 214.191584] __lock_acquire from lock_acquire+0xfc/0x378
[ 214.196918] lock_acquire from __mutex_lock+0x9c/0x8a8
[ 214.202083] __mutex_lock from mutex_lock_nested+0x1c/0x24
[ 214.207597] mutex_lock_nested from spidev_ioctl+0x8e0/0xab8
[ 214.213284] spidev_ioctl from sys_ioctl+0x4d0/0xe2c
[ 214.218277] sys_ioctl from ret_fast_syscall+0x0/0x1c
[ 214.223351] Exception stack(0xe75cdfa8 to 0xe75cdff0)
[ 214.228422] dfa0: 00000000 00001000 00000003 40206b00 bee266e8 bee266e0
[ 214.236617] dfc0: 00000000 00001000 006a71a0 00000036 004c0040 004bfd18 00000000 00000003
[ 214.244809] dfe0: 00000036 bee266c8 b6f16dc5 b6e8e5f6
Fix it by introducing an unlocked variant of spidev_sync() and calling it
from spidev_message() while other users who don't check the spidev->spi's
existence keep on using the locking flavor.
Reported-by: Francesco Dolcini <francesco@dolcini.it>
Fixes: 1f4d2dd45b ("spi: spidev: fix a race condition when accessing spidev->spi")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
Link: https://lore.kernel.org/r/20230116144149.305560-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to using the u16 type in the min_t() macros the SPI transfer length
will be cast to word before participating in the conditional statement
implied by the macro. Thus if the transfer length is greater than 64KB the
Tx/Rx FIFO threshold level value will be determined by the leftover of the
truncated after the type-case length. In the worst case it will cause the
dramatical performance drop due to the "Tx FIFO Empty" or "Rx FIFO Full"
interrupts triggered on each xfer word sent/received to/from the bus.
The problem can be easily fixed by specifying the unsigned int type in the
min_t() macros thus preventing the possible data loss.
Fixes: ea11370fff ("spi: dw: get TX level without an additional variable")
Reported-by: Sergey Nazarov <Sergey.Nazarov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230113185942.2516-1-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The uevent() callback in struct bus_type should not be modifying the
device that is passed into it, so mark it as a const * and propagate the
function signature changes out into all relevant subsystems that use
this callback.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the rpcif_{en,dis}able_rpm() wrappers just take a pointer to a
device structure, there is no point in keeping them. Remove them, and
update the callers to call Runtime PM directly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d87aa5d7e4a39b18f7e2e0649fee0a45b45d371f.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Most rpcif_*() API functions do not need access to any other fields in
the rpcif structure than the device pointer. Simplify dependencies by
passing the device pointer instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/0460fe82ba348cedec7a9a75a8eff762c50e817b.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The s3c24xx platform was removed,s o there are no remaining users
for its spi driver.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge series from Hector Martin <marcan@marcan.st>:
Commits f6c911f330 ("spi: dt-bindings: Introduce
spi-cs-setup-ns property") and 33a2fde5f7 ("spi: Introduce
spi-cs-setup-ns property") introduced a new property to represent the
CS setup delay in the device tree, but they have some issues:
- The property is only parsed as a 16-bit integer number of nanoseconds,
which limits the maximum value to ~65us. This is not a reasonable
upper limit, as some devices might need a lot more.
- The property name is inconsistent with other delay properties, which
use a "*-delay-ns" naming scheme.
- Only the setup delay is introduced, but not the related hold and
inactive delay times.
This series fixes the issues and adds support for the two missing
properties. Please pull in the first 3 patches as fixes for 6.2, to
avoid introducing a problematic DT API in this release. The last two
patches can wait until 6.3, though are probably harmless to throw in
as fixes too, since they're trivial.
Now that we support parsing the setup time from the Device Tree, we can
also easily support the remaining hold and inactive time delay values.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-4-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
65us is not a reasonable maximum for this property, as some devices
might need a much longer setup time (e.g. those driven by firmware on
the other end). Plus, device tree property values are in 32-bit cells
and smaller widths should not be used without good reason.
Also move the logic to a helper function, since this will later be used
to parse other CS delay properties too.
Fixes: 33a2fde5f7 ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-2-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
The OMAP7xx/OMAP8xx support was removed since all of its boards
have no remaining users. Remove its spi driver as well.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: linux-omap@vger.kernel.org
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Fabrice Crohas <fcrohas@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the removal of the unused board files, I went through the
omap1 code to look for code that no longer has any callers
and remove that.
In particular, support for the omap7xx/omap8xx family is now
completely unused, so I'm only leaving omap15xx/omap16xx/omap59xx.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The newly added spi-cs-setup-ns doesn't really fit with the existing
property names for delays, rename it so that it does before it makes it
into a release and becomes ABI.
The two debug messages in spidev_open() dereference spidev->spi without
taking the lock and without checking if it's not null. This can lead to
a crash. Drop the messages as they're not needed - the user-space will
get informed about ENOMEM with the syscall return value.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a spinlock in place that is taken in file_operations callbacks
whenever we check if spidev->spi is still alive (not null). It's also
taken when spidev->spi is set to NULL in remove().
This however doesn't protect the code against driver unbind event while
one of the syscalls is still in progress. To that end we need a lock taken
continuously as long as we may still access spidev->spi. As both the file
ops and the remove callback are never called from interrupt context, we
can replace the spinlock with a mutex.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The two debug messages in spidev_open() dereference spidev->spi without
taking the lock and without checking if it's not null. This can lead to
a crash. Drop the messages as they're not needed - the user-space will
get informed about ENOMEM with the syscall return value.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
There's a spinlock in place that is taken in file_operations callbacks
whenever we check if spidev->spi is still alive (not null). It's also
taken when spidev->spi is set to NULL in remove().
This however doesn't protect the code against driver unbind event while
one of the syscalls is still in progress. To that end we need a lock taken
continuously as long as we may still access spidev->spi. As both the file
ops and the remove callback are never called from interrupt context, we
can replace the spinlock with a mutex.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230106100719.196243-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Hector Martin <marcan@marcan.st>:
This brings the name of the cs-setup-ns parameter which was added during
the merge window into line with other delay properties.
From: Hector Martin <marcan@marcan.st>
Date: Wed, 04 Jan 2023 18:36:26 +0900
Message-Id: <20230104093631.15611-1-marcan@marcan.st>
MIME-Version: 1.0
Content-Type: text/plain; charset="utf-8"
Content-Transfer-Encoding: 7bit
Merge changes from Hector Martin <marcan@marcan.st>:
This brings the name of the cs-setup-ns parameter which was added during
the merge window into line with other delay properties.
As mentioned in the corresponding DT binding commit, the naming scheme
for delay properties includes "delay" in the name, so let's keep that
consistent.
Fixes: 33a2fde5f7 ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-3-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
A 100 ms delay is inserted between tests by default in order to "detect
the individual tests when using a logic analyzer". However, such delays
are unnecessary when using this module for automated regression testing,
so allow them to be disabled with a module parameter.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230103152211.3034779-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Yang Yingliang <yangyingliang@huawei.com>:
After introducing devm_spi_alloc_host/spi_alloc_host(), the legacy
named function devm_spi_alloc_master/spi_alloc_master() can be replaced.
And also change other legacy name master/slave to modern name host/target
or controller.
When a platform is booted with devicetree and does not provide a
platform data structure, the driver creates one internally. enable_dma
should not be set in this structure when creating it; the probe function
will set it later if DMA channels are specified via the devicetree.
Setting enable_dma = 1 when creating this internal platform data can
lead to pl022_dma_probe() finding bogus DMA channels (since there is no
channel filter specified) when no DMA channels are specified in the
devicetree.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230102160852.3090202-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If xSPI is in x2/x4/x8 mode to calculate busy
cycles, busy bits count must be divided by the number
of lanes.
If opcommand is using 8 busy bits, but SPI is
in x4 mode, there will be only 2 busy cycles.
Signed-off-by: Witold Sadowski <wsadowski@marvell.com>
Reviewed-by: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20221219144254.20883-2-wsadowski@marvell.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the irq is enabled after the spi si registered, there can be a race
with the initialization of the devices on the spi bus.
Eg:
mtk-spi 1100a000.spi: spi-mem transfer timeout
spi-nor: probe of spi0.0 failed with error -110
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000010
...
Call trace:
mtk_spi_can_dma+0x0/0x2c
Fixes: c6f7874687 ("spi: mediatek: Enable irq when pdata is ready")
Reported-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20221225-mtk-spi-fixes-v1-0-bb6c14c232f8@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SE DMA mode can be used for larger transfers and FIFO mode
for smaller transfers.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1670509544-15977-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message on
fsl_spi hardware, this should be very unusual.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOmIFQACgkQJNaLcl1U
h9BD2Qf/byfpQzO+8mnDIenWP3X/WMNxJybIe1zaZXOEPRdxmE24Q7BvROnu/80C
jiKGJ3x/n5dhgnBvBJYdTw93BwDUJIcoz42WHnJMxRpxHPd/IX9N8NEOtMU5Z7T6
R/9LPpTja33CXXqbvhZw2M1dhVxbEZ9VgPVOemz0nLQtYnM4/Y8wj2RFOGgJFZ91
krY8S7VkLp6ycdv+a9ofMck+l05zpQ7TG54Nmr/0wvexosj7x7JLyZx6CahGL4/E
PMF7MDblLIrCvMtJPs2gpjHTiAReu85akoOvxBcZc5JNNynp8GXmDcOwgPRbZ7pi
bAJzH0LnwPQycTX+e46QMpViyVll7g==
=zqM3
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"One driver specific change here which handles the case where a SPI
device for some reason tries to change the bus speed during a message
on fsl_spi hardware, this should be very unusual"
* tag 'spi-fix-v6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fsl_spi: Don't change speed while chipselect is active
Commit c9bfcb3151 ("spi_mpc83xx: much improved driver") made
modifications to the driver to not perform speed changes while
chipselect is active. But those changes where lost with the
convertion to tranfer_one.
Previous implementation was allowing speed changes during
message transfer when cs_change flag was set.
At the time being, core SPI does not provide any feature to change
speed while chipselect is off, so do not allow any speed change during
message transfer, and perform the transfer setup in prepare_message
in order to set correct speed while chipselect is still off.
Reported-by: Herve Codina <herve.codina@bootlin.com>
Fixes: 64ca1a034f ("spi: fsl_spi: Convert to transfer_one")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/8aab84c51aa330cf91f4b43782a1c483e150a4e3.1671025244.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for it
on Atmel systems. Otherwise the updates are mostly feature additions
and cleanups to existing drivers.
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of the
timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450 FIU
and Socionext F_OSPI.
There's a straightforward add/add conflict with the rpmsg tree in the
xilinx firmware code (both trees got new users of the firmware added
each needing new firmware<->kernel ioctls).
There's a cross tree merge with I2C in order to use the new
i2c_client_get_device_id() helper in some I2C attached SPI controllers
as part of their conversion to I2C's probe_new() API.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOXIt8ACgkQJNaLcl1U
h9Alrwf9F6mgj3eaDbhPH2lJ+zZRDJrdrMxT1US1tWixCMEZilntDXVecJA+/htp
/tJ0InGXsyr+6p9lXsFGQZGuaSIzKh0h2OW3JCakPGfp6HvA8+qXqHYSLKzIXtYU
/lk+kR+H6TGG+pjFtwkNnbCY/pYAlOtdjdmfui68VSsqWYX1W1kJDhDEkpUZePUx
Bc9wGgGByL0ZEHMQ/O6d8Nc/JzfTQPFuPB9ZHpIHFuPuAnjDQx+veaWejpVawy+D
8crMM7OgGpHy1hENSN786039QvNbWvVucPyVwJfU4SDhrT6oNNmEA/RF/DqTt472
8cbNG5H5bSR0Youv9ofxdP9bAOHhtg==
=eJDv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A busy enough release, but not for the core which has only seen very
small updates. The biggest addition is the readdition of support for
detailed configuration of the timings around chip selects. That had
been removed for lack of use but there's been applications found for
it on Atmel systems. Otherwise the updates are mostly feature
additions and cleanups to existing drivers.
Summary:
- Provide a helper for getting device match data in a way that
abstracts away which firmware interface is being used.
- Re-add the spi_set_cs_timing() API for detailed configuration of
the timing around chip select and support it on Atmel.
- Support for MediaTek MT7986, Microchip PCI1xxxx, Nuvoton WPCM450
FIU and Socionext F_OSPI"
* tag 'spi-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (66 commits)
spi: dt-bindings: Convert Synquacer SPI to DT schema
spi: spi-gpio: Don't set MOSI as an input if not 3WIRE mode
spi: spi-mtk-nor: Add recovery mechanism for dma read timeout
spi: spi-fsl-lpspi: add num-cs binding for lpspi
spi: spi-fsl-lpspi: support multiple cs for lpspi
spi: mtk-snfi: Add snfi support for MT7986 IC
spi: spidev: mask SPI_CS_HIGH in SPI_IOC_RD_MODE
spi: cadence-quadspi: Add minimum operable clock rate warning to baudrate divisor calculation
spi: microchip: pci1xxxx: Add suspend and resume support for PCI1XXXX SPI driver
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix warning in example (missing reg property)
spi: dt-bindings: nuvoton,wpcm450-fiu: Fix error in example (bogus include)
spi: mediatek: Enable irq when pdata is ready
spi: spi-mtk-nor: Unify write buffer on/off
spi: intel: Add support for SFDP opcode
spi: intel: Take possible chip address into account in intel_spi_read/write_reg()
spi: intel: Implement adjust_op_size()
spi: intel: Use ->replacement_op in intel_spi_hw_cycle()
spi: cadence: Drop obsolete dependency on COMPILE_TEST
spi: Add Nuvoton WPCM450 Flash Interface Unit (FIU) bindings
spi: wpcm-fiu: Add direct map support
...
The addition of 3WIRE support would affect MOSI direction even
when still in standard (4 wire) mode. This can lead to MOSI being
at an invalid logic level when a device driver sets an SPI
message with a NULL tx_buf.
spi.h states that if tx_buf is NULL then "zeros will be shifted
out ... " If MOSI is tristated then the data shifted out is subject
to pull resistors, keepers, or in the absence of those, noise.
This issue came to light when using spi-gpio connected to an
ADS7843 touchscreen controller. MOSI pulled high when clocking
MISO data in caused the SPI device to interpret this as a command
which would put the device in an unexpected and non-functional
state.
Fixes: 4b859db2c6 ("spi: spi-gpio: add SPI_3WIRE support")
Fixes: 5132b3d283 ("spi: gpio: Support 3WIRE high-impedance turn-around")
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Link: https://lore.kernel.org/r/20221207230853.6174-1-kris@embeddedTS.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The state machine of MTK spi nor controller may be disturbed by some
glitch signals from the relevant BUS during dma read, Although the
possibility of causing the dma read to fail is next to nothing,
However, if error-handling is not implemented, which makes the feature
somewhat risky.
Add an error-handling mechanism here, reset the state machine and
re-read the data when an error occurs.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221207055435.30557-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
has changed the user-space interface so that bogus SPI_CS_HIGH started
to appear in the mask returned by SPI_IOC_RD_MODE even for active-low CS
pins. Commit 138c9c32f0
("spi: spidev: Fix CS polarity if GPIO descriptors are used") fixed only
SPI_IOC_WR_MODE part of the problem. Let's fix SPI_IOC_RD_MODE
symmetrically.
Test case:
#include <sys/ioctl.h>
#include <fcntl.h>
#include <linux/spi/spidev.h>
int main(int argc, char **argv)
{
char modew = SPI_CPHA;
char moder;
int f = open("/dev/spidev0.0", O_RDWR);
if (f < 0)
return 1;
ioctl(f, SPI_IOC_WR_MODE, &modew);
ioctl(f, SPI_IOC_RD_MODE, &moder);
return moder == modew ? 0 : 2;
}
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20221130162927.539512-1-alexander.sverdlin@siemens.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This Cadence QSPI IP has a 4-bit clock divisor field
for baud rate division. For example:
0b0000 = /2
0b0001 = /4
0b0010 = /6
...
0b1111 = /32
The maximum divisor is 32
(when div = CQSPI_REG_CONFIG_BAUD_MASK).
If we assume a reference clock of 500MHz and we set
our spi-max-frequency to something low, such as 10 MHz.
The calculated bit field for the divisor ends up being:
DIV_ROUND_UP(500000000/(2*10000000))-1 = 25
25 is 0b11001... which truncates to a divisor field of 0b1001 (or /20).
This is higher than our anticipated max-frequency of 10MHz
(500MHz/20 = 25 MHz). Instead, let's make sure we're always using
the maximum divisor (/32) in this case and give the user a warning about
the rate adjustment.
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison@timesys.com>
Link: https://lore.kernel.org/r/20221128164147.158441-1-nathan.morrison@timesys.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the device does not come straight from reset, we might receive an IRQ
before we are ready to handle it.
Fixes:
[ 0.832328] Unable to handle kernel read from unreadable memory at virtual address 0000000000000010
[ 1.040343] Call trace:
[ 1.040347] mtk_spi_can_dma+0xc/0x40
...
[ 1.262265] start_kernel+0x338/0x42c
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221128-spi-mt65xx-v1-0-509266830665@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The logical structures of mtk_nor_write_buffer_enable and
mtk_nor_write_buffer_disable are very similar, So it is necessary to
combine them into one.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Link: https://lore.kernel.org/r/20221115124655.10124-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Intel SPI-NOR controller supports SFDP (Serial Flash Discoverable
Parameter) opcode so add it to the list of supported opcodes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-5-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows us to get rid of the checks in the intel_spi_[sh]w_cycle()
and makes it possible for the SPI-NOR core to split the transaction into
smaller chunks as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025064623.22808-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmNoPiAeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGPmcH/2dl4Zu+ofzwziH4
MxIHeSdL62tFEtD+643hTArXLR/8YeZkt17q0vaQa0WQFC09vtYepdvAuiQIGrDm
69hXY20BIARz1bwqmGuP+gNhjFeuHVy5B9qIKV7z0HoO3Guf2BoAG14LEEBsc5SO
RrZSVDRlGHnstMBx4zplWDNXOxehumwoPInFyKC8SqDg464BCeo/ErJbzwMXPdBw
RPUuDh3m9iwN6BhjlbM9UhtNEbakVKw+LaTO5eYtiPValyJ40ws/wQ/SrDc/k9YA
1E1gFlUMgPwNz0uVBEO+NcRRsQHiBqrEyLDpvg5RkE2xnOJwMrm9LDY6RqwJD/w1
4UKcuAs=
=ls46
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmOBFIEACgkQJNaLcl1U
h9A4zAgAgVnP6727ptBIpTE55chOrOPyeVI0bE1xAZ3jyBEfqCFk9yb7wmr9NZY4
tJkuRlBlDGFVvpYavk18m8ZbwaedGqYfRqxmWSFdq19dmbSXn6DdZglrtf19zN2S
eNEFSbp/CAjxZAGAdoErf3VjFOHyEt8sm4K6443BbkvKhObKAR5Np2tlEURV2ezJ
UAJZXcc+Muu273nH5aaXpKyagL/kupeUns5kcJ73sK3qozxvjrEh8vHhRHx+CQAH
qmEqe8dovBWxZUXr7rYDia3xVxCeZGjIQIRsJX/9oA3YuU9entNZx3QeGlMRvue8
wTlhLVYhO+WlB2AfYtOAPNyJAizttA==
=CYxU
-----END PGP SIGNATURE-----
Merge tag 'v6.1-rc4' into spi-6.2
Linux 6.1-rc4 which should get my CI working on RPi3s again.
Merge series from Jonathan Neuschäfer <j.neuschaefer@gmx.net>:
This patchset adds DT bindings and a driver for the Flash Interface Unit
(FIU), the SPI flash controller in the Nuvoton WPCM450 BMC SoC. It
supports four chip selects, and direct (memory-mapped) access to 16 MiB
per chip. Larger flash chips can be accessed by software-defined SPI
transfers.
The existing NPCM7xx FIU driver is sufficitently incompatible with the
WPCM450 FIU that I decided to write a new driver.
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221125083114.67e7f83c@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
Besides software controlled SPI transfers (UMA, "user mode access"), FIU
also supports a 16 MiB mapping window per attached flash chip.
This patch implements direct mapped read access, to speed up flash reads.
Without direct mapping:
# time dd if=/dev/mtd0ro of=dump bs=1M
16+0 records in
16+0 records out
real 1m 47.74s
user 0m 0.00s
sys 1m 47.75s
With direct mapping:
# time dd if=/dev/mtd0ro of=dump bs=1M
16+0 records in
16+0 records out
real 0m 30.81s
user 0m 0.00s
sys 0m 30.81s
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-4-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The Flash Interface Unit (FIU) is the SPI flash controller in the
Nuvoton WPCM450 BMC SoC. It supports four chip selects, and direct
(memory-mapped) access to 16 MiB per chip. Larger flash chips can be
accessed by software-defined SPI transfers.
The FIU in newer NPCM7xx SoCs is not compatible with the WPCM450 FIU.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-3-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
This series adds dt-bindings and a driver for Socionext F_OSPI controller
for connecting an SPI Flash memory over up to 8-bit wide bus.
The controller supports up to 4 chip selects.
Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI Flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.
This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221124003351.7792-3-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A few fixes, all device specific. The most important ones are for the
i.MX driver which had a couple of nasty data corruption inducing errors
appear after the change to support PIO mode in the last merge window
(one introduced by the change and one latent one which the PIO changes
exposed), thanks to Frieder, Fabio, Marc and Marek for jumping on that
and resolving the issues quickly once they were found.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmN+RHAACgkQJNaLcl1U
h9AcOQf9HQbm5UxLbb2+ufC96M/XyCPAunOFPfIKsIEIZSQuM/abdb+jwV34kn/I
ApnFrEOz6/4i9iDotpf6fCe037r07vuy2bJSHCmszgE0xEvCfioGf/ssxw+eaQf7
GmDnCy9cnyIe0SS8x0+oOUGj4Mi3pLBZmLUr6nU2W3BwGkUXM3BXk3qTKvTi2B10
XFwnNI+hImni2KrVSkpKgCr6v0WQ/phwtnbRw/YeiGzhaF/427llgqd/mJCgmFkk
WStH83DdGke0qUF+AqFppfDVMsH5+r47tAaaDuBNRLSxDbLsOsHm4YetO+nFs7BK
JqDIzECtVPcXKhaWDdIiDoVQkt1YPg==
=k58Q
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes, all device specific.
The most important ones are for the i.MX driver which had a couple of
nasty data corruption inducing errors appear after the change to
support PIO mode in the last merge window (one introduced by the
change and one latent one which the PIO changes exposed).
Thanks to Frieder, Fabio, Marc and Marek for jumping on that and
resolving the issues quickly once they were found"
* tag 'spi-fix-v6.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-imx: spi_imx_transfer_one(): check for DMA transfer first
spi: tegra210-quad: Fix duplicate resource error
spi: dw-dma: decrease reference count in dw_spi_dma_init_mfld()
spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
spi: mediatek: Fix DEVAPC Violation at KO Remove
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-566-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Acked-for-Backlight-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20221118224540.619276-565-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The at91 QSPI IP uses a default value of half of the period of the QSPI
clock period for the cs-setup time, which is not always enough, an example
being the sst26vf064b SPI NOR flash which requires a minimum cs-setup time
of 5 ns. It was observed that none of the at91 SoCs can fulfill the
minimum CS setup time for the aforementioned flash, as they operate at
high frequencies and half a period does not suffice for the required CS
setup time. Add support for configuring the CS timing in the controller.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-5-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4ccf359849 ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.
Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.
One will notice that this support is a bit different from the one that was
removed in commit 4ccf359849 ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI framework checks for each transfer (with the struct
spi_controller::can_dma callback) whether the driver wants to use DMA
for the transfer. If the driver returns true, the SPI framework will
map the transfer's data to the device, start the actual transfer and
map the data back.
In commit 07e7593877 ("spi: spi-imx: add PIO polling support") the
spi-imx driver's spi_imx_transfer_one() function was extended. If the
estimated duration of a transfer does not exceed a configurable
duration, a polling transfer function is used. This check happens
before checking if the driver decided earlier for a DMA transfer.
If spi_imx_can_dma() decided to use a DMA transfer, and the user
configured a big maximum polling duration, a polling transfer will be
used. The DMA unmap after the transfer destroys the transferred data.
To fix this problem check in spi_imx_transfer_one() if the driver
decided for DMA transfer first, then check the limits for a polling
transfer.
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Link: https://lore.kernel.org/all/20221111003032.82371-1-festevam@gmail.com
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Cc: David Jander <david@protonic.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20221116164930.855362-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
controller data alloc is done with client device data causing duplicate
resource error. Allocate memory using controller device when using devm
Fixes: f89d2cc396 ("spi: tegra210-quad: use devm call for cdata memory")
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20221117070320.18720-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make the driver be able to bit-bang a GPIO for the Chip Select pin of
select peripherals.
The GPIO value is driven by the driver in that case, and none of the
hardware Chip Select bits will be populated in the PUSHR register for
the TX commands constructed for this peripheral.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221111211356.545026-1-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pci_get_device() will increase the reference count for the returned
pci_dev. Since 'dma_dev' is only used to filter the channel in
dw_spi_dma_chan_filer() after using it we need to call pci_dev_put() to
decrease the reference count. Also add pci_dev_put() for the error case.
Fixes: 7063c0d942 ("spi/dw_spi: add DMA support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20221116093204.46700-1-wangxiongfeng2@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx 30820000.spi: mx51_ecspi_clkdiv: fin: 50000000, fspi: 50000000,
post: 0, pre: 0
Fixes: 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes: 07e7593877 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The timeout value of the current dma read is unreasonable. For example,
If the spi flash clock is 26Mhz, It will takes about 1.3ms to read a
4KB data in spi mode. But the actual measurement exceeds 50s when a
dma read timeout is encountered.
In order to be more accurately, It is necessary to use usecs_to_jiffies,
After modification, the measured timeout value is about 130ms.
Signed-off-by: bayi cheng <bayi.cheng@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221114081327.25750-1-bayi.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A relatively large batch of fixes here but all device specific, plus an
update to MAINTAINERS. The summary print change to the STM32 driver is
fixing an issue where the driver could easily end up spamming the logs
with something that should be a debug message.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNuPWkACgkQJNaLcl1U
h9BZJQf/Rj3kjTdwjccp+QXTrXQZVMjkXYUuLHbUokO2Mzy+U3mNCkJuvLJjAvSw
kqFBbJNYIm1jItRoqOkwlnNb0hw+QZAzBivi4DLPZJUwEeT6LxQdlYvepy6bEjCW
XJpTMFxDDaWkFUftl+tLZFN2VxHaVHEVTJ5aMu2ija0mjG1M5vrYtgVemyJ+v2/o
0nhXgnRe7Fq2+MqJazVzYs6ZxCvpIiU18a4WLD5BPGTIZhdfE0UXG+QGqWV4toHI
uZWnV+NWEKNzMGS/QdcHZYQHWlcQBR/g5kPFQFCl2D+aK9CmakHc6Bk99H6tRdLn
xYHjHafs6BwCG3eBfE/hxD8rsfTNmw==
=UfdB
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A relatively large batch of fixes here but all device specific, plus
an update to MAINTAINERS.
The summary print change to the STM32 driver is fixing an issue where
the driver could easily end up spamming the logs with something that
should be a debug message"
* tag 'spi-fix-v6.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: amd: Fix SPI_SPD7 value
spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
spi: meson-spicc: fix do_div build error on non-arm64
spi: intel: Use correct mask for flash and protected regions
spi: mediatek: Fix package division error
spi: tegra210-quad: Don't initialise DMA if not supported
MAINTAINERS: Update HiSilicon SFC Driver maintainer
spi: meson-spicc: move wait completion in driver to take bursts delay in account
spi: stm32: Print summary 'callbacks suppressed' message
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32 44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate 125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the const array ls1028a_soc_attr on the stack, instead
make it static. Also makes the object code smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20221102152904.143423-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes :
error: passing argument 1 of '__div64_32' from incompatible pointer type
By passing an uint64_t as first variable to do_div().
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04694e5002 ("spi: meson-spicc: move wait completion in driver to take bursts delay in account")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221027-b4-spicc-burst-delay-fix-v2-0-8cc2bab3417a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071720.3041094-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221029071529.3019626-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7e963fb2a3 ("spi: mediatek: add ipm design support
for MT7986") makes a mistake on package dividing operation
(one change is missing), need to fix it.
Background:
Ipm design is expanding the HW capability of dma (adjust package
length from 1KB to 64KB), and using "dev_comp->ipm_support" flag
to indicate it.
Issue description:
Ipm support patch (said above) is missing to handle remainder at
package dividing operation.
One case, a transmission length is 65KB, is will divide to 1K
(package length) * 65(package loop) in non-ipm desgin case, and
will divide to 64K(package length) * 1(package loop) + 1K(remainder)
in ipm design case. And the 1K remainder will be lost with the
current SW flow, and the transmission will be failure.
So, it should be fixed.
Solution:
Add "ipm_design" flag in function "mtk_spi_get_mult_delta()" to
indicate HW capability, and modify the parameters corespondingly.
fixes: 7e963fb2a3 ("spi: mediatek: add ipm design support for MT7986")
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20221021091653.18297-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The following error messages are observed on boot for Tegra234 ...
ERR KERN tegra-qspi 3270000.spi: cannot use DMA: -19
ERR KERN tegra-qspi 3270000.spi: falling back to PIO
Tegra234 does not support DMA for the QSPI and so initialising the DMA
is expected to fail. The above error messages are misleading for devices
that don't support DMA and so fix this by skipping the DMA
initialisation for devices that don't support DMA.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221026155633.141792-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmNZkaEACgkQJNaLcl1U
h9DKzAf+KmSNUIZ8rdfTTSvYj1SEuKd5O0YGLtRZsGLO6jhSNJ1EISCjw+9NHnoA
U/AKnnTBdexb+T5623prQL9ZU0U+JmMciHn2c34eDkvQcpdbD0ZbbqzcqxkUnPQ/
Ci5W0/9jlv7NupBSR6HXLJxjkuAVWNNUZPdy4Pb89kZIB4m/E/geRU+t/ZZgpvuf
v92AnRc0FtKlTFs2jrzScfV/R4+cygnoUoe2tJeDHYiN6ixJDJYZcU1yOcrE9544
+ovu166ZMRR6FuZ4Vd6Gso/befdaswUAwwWGghzg5IoWhIzvCkIHgtp78dk7oL29
xGgoq3lSjfzskvwNnHOWDB4tyQY7wg==
=Ni1v
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of mostly unremarkable fixes for SPI that have built up
since the merge window, all driver specific.
The change to the qup adding support for GPIO chip selects is fixing a
regression due to the removal of legacy GPIO handling, the driver had
previously been silently relying on the legacy GPIO support in a
slightly broken way which worked well enough on some systems. Fixing
it is simply a case of setting a couple of bits of information in the
driver description"
* tag 'spi-fix-v6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: aspeed: Fix window offset of CE1
spi: qup: support using GPIO as chip select line
spi: intel: Fix the offset to get the 64K erase opcode
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
spi: mpc52xx: Replace NO_IRQ by 0
spi: spi-mem: Fix typo (of -> or)
spi: spi-gxp: fix typo in SPDX identifier line
spi: tegra210-quad: Fix combined sequence
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221026122951.331638-1-bigeasy@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Some delay occurs between each bursts, thus the default delay is wrong
and a timeout will occur with big enough transfers.
The solution is to handle the timeout management in the driver and
add some delay for each bursts in the timeout calculation.
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221026-spicc-burst-delay-v1-0-1be5ffb7051a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Currently the SPI PXA2xx devices on Intel platforms can be instantiated
via the following paths:
1) as ACPI LPSS device on Haswell, Bay Trail and Cherry Trail;
2) as ACPI LPSS device on the Sky Lake and newer;
3) as PCI LPSS device on Haswell, Bay Trail and Cherry Trail;
4) as PCI LPSS device on the Sky Lake and newer;
5) as PCI device via ID table.
Each of these cases provides some platform related data differently,
i.e.:
1) via drivers/acpi/acpi_lpss.c and drivers/spi/spi-pxa2xx.c
2) via drivers/mfd/intel-lpss-acpi.c
3) via drivers/spi/spi-pxa2xx-pci.c
4) via drivers/mfd/intel-lpss-pci.c and drivers/spi/spi-pxa2xx.c
5) via drivers/spi/spi-pxa2xx-pci.c
This approach has two downsides:
a) there is no data propagated in the case #2 because we can't have
two or more drivers to match the same ACPI ID and hence some cases
are still not supported (Sky Lake and newer ACPI enabled LPSS);
b) the data is duplicated over two drivers in the cases #1 & #4 and,
besides to be a bloatware, it is error prone (e.g. Lakefield has
a wrong data right now due to missed PCI entry in the spi-pxa2xx.c).
This series fixes the downsides, and enables previously unsupported
cases.
There is no code that uses ID tables directly, except the
struct device_driver at the end of the file. Hence, move
tables closer to its user. It's always possible to access
them via pointer to a platform device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221021190018.63646-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the PCI enumerated devices provide a property with SSP type,
there is no more necessity to bear the copy of the ID table here.
Remove it for good.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow to set the Intel SSP type by reading the property.
Only apply this to the known MFD enumerated LPSS devices.
The check is done by the looking for the specifically
named IO memory resource provided by upper layer. This
won't be an issue in the future because we strictly
prioritize the order in which we are looking for the SSP
type in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we blindly apply the SSP type value from any source of the
information. Increase robustness by validating the value before use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221021190018.63646-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_{get_and_}ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019092635.1176622-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes: ea8be08cc9 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amjad Ouled-Ameur <aouledameur@baylibre.com>:
Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.
The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.
Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message.
Between SPI transactions, all SPI pins are in HiZ state. When using the SS
signal from the SPICC controller it's not an issue because when the
transaction resumes all pins come back to the right state at the same time
as SS.
The problem is when we use CS as a GPIO. In fact, between the GPIO CS
state change and SPI pins state change from idle, you can have a missing or
spurious clock transition.
Set a bias on the clock depending on the clock polarity requested before CS
goes active, by passing a special "idle-low" and "idle-high" pinctrl state
and setting the right state at a start of a message
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Link: https://lore.kernel.org/r/20221004-up-aml-fix-spi-v4-2-0342d8e10c49@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In commit 7a908832ac ("spi: imx: add fallback feature") the last
user of the struct spi_imx_devtype_data::disable_dma callback was
removed. However the disable_dma member of struct spi_imx_devtype_data
and the callback itself was not removed.
Remove struct spi_imx_devtype_data::disable_dma and mx51_disable_dma()
as they are unused.
Cc: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20221021131051.1777984-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleaning up the driver to use pm_ptr() macro instead of ifdeffery
that makes it simpler and allows the compiler to remove those functions
if built without CONFIG_PM and CONFIG_PM_SLEEP support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20221020194500.10225-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
A bunch of improvements to the driver:
- Fix kernel-doc warnings in GQSPI driver.
- Avoid setting CPOL, CPHA & baud rate multiple times.
- Add Versal platform support in GQSPI driver.
- Add tap delay support in GQSPI driver.
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019093318.1183190-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset value of the mapping window in the kernel structure is
calculated using the value of the previous window offset. This doesn't
reflect how the HW is configured and can lead to erroneous setting of
the second flash device (CE1).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Fixes: e3228ed928 ("spi: spi-mem: Convert Aspeed SMC driver to spi-mem")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221016155722.3520802-1-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add tap delay support for GQSPI controller on Versal platform.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-8-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
GQSPI controller uses the internal clock for loopback mode. The loopback
mode is used with the high-speed Quad SPI timing mode, where the memory
interface clock needs to be greater than 40 MHz. Based on the tap delay
value programmed, the internal clock is delayed and used for capturing
the data.
Based upon the frequency of operation set the recommended tap delay
values in GQSPI driver.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-6-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During every transfer the GQSPI driver configures the baud rate value. But
when there is no change in the SPI clock frequency the driver should avoid
rewriting the same baud rate value to the configuration register. Update
GQSPI driver to rewrite the baud rate value if there is any change in SPI
clock frequency.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-4-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During every transfer GQSPI driver writes the CPOL & CPHA values to the
configuration register. But the CPOL & CPHA values do not change in between
multiple transfers, so moved the CPOL & CPHA initialization to hardware
init so that the values are written only once.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Document zynqmp_qspi ctrl and op_lock member description. It also adds
return documentation for 'zynqmp_qspi_setuprxdma' and zynqmp_qspi_read_op.
Fixes below kernel-doc warnings-
spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'ctlr' not
described in 'zynqmp_qspi'
spi-zynqmp-gqspi.c:178: warning: Function parameter or member 'op_lock'
not described in 'zynqmp_qspi'
spi-zynqmp-gqspi.c:737: warning: No description found for return value of
'zynqmp_qspi_setuprxdma'
spi-zynqmp-gqspi.c:822: warning: No description found for return value of
'zynqmp_qspi_read_op'
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20221011062040.12116-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all zero page implementations use empty_zero_page global pointer so
let's substitute empty_zero_page occurence with helper ZERO_PAGE(0).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Link: https://lore.kernel.org/r/20221018215755.33566-2-giulio.benetti@benettiengineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function bcm_qspi_remove() returns zero unconditionally. Make it
return void.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221017200143.1426528-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
No functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221017171243.57078-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_{get_and}_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145852.1882221-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Microchip pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. SPI is one of the functions in the multi-function endpoint. This
function has 2 SPI masters, operates at a maximum frequency of 30 MHz and supports
7 client devices per master. This patch adds complete functionality to the SPI
function except for suspend and resume.
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20221006050514.115564-2-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function mchp_corespi_enable() is defined in the spi-microchip-core.c
file, but not called elsewhere, so delete this unused function.
drivers/spi/spi-microchip-core.c:122:20: warning: unused function 'mchp_corespi_enable'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2418
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20221017092141.9789-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the device with QUP SPI adapter are actually using GPIO-s for
chip select.
However, this stopped working after ("spi: Retire legacy GPIO handling")
as it introduced a check on ->use_gpio_descriptors flag and since spi-qup
driver does not set the flag it meant that all of boards using GPIO-s and
with QUP adapter SPI devices stopped working.
So, to enable using GPIO-s again set ->use_gpio_descriptors to true and
populate ->max_native_cs.
Fixes: f48dc6b966 ("spi: Retire legacy GPIO handling")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221006194819.1536932-1-robert.marko@sartura.hr
Signed-off-by: Mark Brown <broonie@kernel.org>
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221012152135.28353-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
