IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Like the c630, the OnePlus 6 is also capable of using both antenna
channels for 2.4 and 5ghz wifi, however unlike the c630 only the first
channel is used for bluetooth.
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211020163557.291803-1-caleb@connolly.tech
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-26-dmitry.baryshkov@linaro.org
Now that the pmic-mpp is a proper hierarchical IRQ chip, add interrupt
controller properties ('interrupt-controller' and '#interrupt-cells').
The interrupts property is no longer needed so remove it.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-25-dmitry.baryshkov@linaro.org
The majority of device tree nodes for mpps use xxxx-state as pinctrl
nodes. Change names of mpps pinctrl nodes for the apq8016-sbc board to
follow that pattern.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-13-dmitry.baryshkov@linaro.org
Add missing "qcom,spmi-mpp" to the compatible list as required by the
node description. Also add gpio-ranges property to mpps device tree
node, adding the mapping between pinctrl and GPIO pins.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-12-dmitry.baryshkov@linaro.org
Add missing "qcom,spmi-mpp" to the compatible list as required by the
node description. Also add gpio-ranges property to mpps device tree
node, adding the mapping between pinctrl and GPIO pins.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-11-dmitry.baryshkov@linaro.org
Add device node for Sleep stats driver which provides various
low power mode stats on sc7180, sc7280, sm8150, sm8250 and sm8350.
Also update the reg size of aoss_qmp device to 0x400.
Cc: devicetree@vger.kernel.org
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1634107104-22197-5-git-send-email-mkshah@codeaurora.org
Add a dts fragment file to support the sc7180 boards with the second
source edp bridge, Parade ps8640.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008113839.v3.2.I187502fa747bc01a1c624ccf20d985fdffe9c320@changeid
Factor out ti-sn65dsi86 edp bridge as a separate dts fragment.
This helps us introduce the second source edp bridge later.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008113839.v3.1.Ibada67e75d2982157e64164f1d11715d46cdc42c@changeid
A new 'chassis-type' root node property has recently been approved for
the device-tree specification, in order to provide a simple way for
userspace to detect the device form factor and adjust their behavior
accordingly.
This patch fills in this property for end-user devices (such as laptops,
smartphones and tablets) based on Qualcomm ARM64 processors.
Signed-off-by: Arnaud Ferraris <arnaud.ferraris@collabora.com>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net> # msm8916
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211016102025.23346-4-arnaud.ferraris@collabora.com
Now that the SMEM binding and driver allows the SMEM node to be
described in the reserved-memory region directly, move the compatible
and hwlock properties to the reserved-memory node and drop the
standadlone node.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Link: https://lore.kernel.org/r/20210930182111.57353-5-bjorn.andersson@linaro.org
Using underscores in device tree nodes is not very common.
Additionally, the _region suffix in "smem_region@..." is not really
useful since it's obvious that it describes a reserved memory region.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210921152120.6710-2-stephan@gerhold.net
Commit 0f6b380d580c ("arm64: dts: qcom: apq8016-sbc: Update modem and WiFi
firmware path") added "firmware-name"s to the APQ8016 SBC (DB410c) device
tree to separate the (test key)-signed firmware from other devices.
However, the added names are a bit confusing. The "modem" firmware used by
DB410c is actually a simplified version for APQ8016 that lacks most of the
modem functionality (phone calls, SMS etc) that is available on MSM8916.
Placing it in "qcom/msm8916/modem.mbn" suggests that it supports all
functionality for MSM and not just the reduced functionality for APQ.
Request the firmware from "qcom/apq8016/modem.mbn" instead to clarify this.
Do the same for "wcnss.mbn" for consistency (although the WCNSS firmware
works just fine on MSM8916).
Finally, add a "_sbc" suffix to the WCNSS_qcom_wlan_nv.bin firmware file.
It seems like the nv.bin firmware is somewhat board specific and can
therefore vary a bit from device to device. This makes it more clear
which board it is intended to be used for.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210922195853.95574-1-stephan@gerhold.net
This is a larger than normal update for Arm SoC specific code, most
of it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for several
defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect settings
in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Mrh2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"This is a larger than normal update for Arm SoC specific code, most of
it in device trees, but also drivers and the omap and at91/sama7
platforms:
- There are four new entries to the MAINTAINERS file: Sven Peter and
Alyssa Rosenzweig for Apple M1, Romain Perier for Mstar/sigmastar,
and Vignesh Raghavendra for TI K3
- Build fixes to address randconfig warnings in sharpsl, dove, omap1,
and qcom platforms as well as the scmi and op-tee subsystems
- Regression fixes for missing CONFIG_FB and other options for
several defconfigs
- Several bug fixes for the newly added Microchip SAMA7 platform,
mostly regarding power management
- Missing SMP barriers to protect accesses to SCMI virtio device
- Regression fixes for TI OMAP, including a boot-time hang on am335x.
- Lots of bug fixes for NXP i.MX, mostly addressing incorrect
settings in devicetree files, and one revert for broken suspend.
- Fixes for ARM Juno/Vexpress devicetree files, addressing a couple
of schema warnings.
- Regression fixes for qualcomm SoC specific drivers and devicetree
files, reverting an mdt_loader change and at least pastially
reverting some of the 5.15 DTS changes, plus some minor bugfixes"
* tag 'armsoc-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (64 commits)
MAINTAINERS: Add Sven Peter as ARM/APPLE MACHINE maintainer
MAINTAINERS: Add Alyssa Rosenzweig as M1 reviewer
firmware: arm_scmi: Add proper barriers to scmi virtio device
firmware: arm_scmi: Simplify spinlocks in virtio transport
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
ARM: sharpsl_param: work around -Wstringop-overread warning
ARM: defconfig: gemini: Restore framebuffer
ARM: dove: mark 'putc' as inline
ARM: omap1: move omap15xx local bus handling to usb.c
MAINTAINERS: Add Vignesh to TI K3 platform maintainership
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
...
29.5V (29p5) is obviously wrong for regulator l4 and l5. Correct them
to be 2.95V (2p95). No functional change.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210926072215.27517-1-shawn.guo@linaro.org
Some multiline properties (spread out over multiple lines to keep length
in check) were not indented properly, leading to misalignment with the
items above. The DT file is still small enough to address this early in
the process.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210925141841.407257-1-marijn.suijten@somainline.org
At the moment, longcheer-l8150 is using a dummy extcon-usb-gpio device
that permanently enables USB gadget mode. This workaround allows USB
to work but is actually wrong and confusing. The "vbus-gpio" used there
refers to an unused (floating) GPIO that is pulled up to make
extcon-usb-gpio report USB gadget mode permanently.
Replace this with the new &pm8916_usbin extcon device that actually
reports if an USB cable is attached or not. This allows the USB PHY
to be turned off when there is no USB cable attached and is much
cleaner overall.
Fixes: 16e8e8072108 ("arm64: dts: qcom: Add device tree for Longcheer L8150")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-3-stephan@gerhold.net
At the moment, USB gadget mode on MSM8916 works only with an extcon
device that reports the correct USB mode. This might be because the
USB PHY needs to be configured appropriately.
Unfortunately there is currently no simple approach to get such an
extcon device during early bring-up. The extcon device for USB VBUS
(i.e. gadget/peripheral mode) is typically provided by the charging
driver which is almost always very complex to port.
On pretty much all devices with PM8916, the USB VBUS is also connected
to the PM8916 "USB_IN" pad, no matter if they use the linear charger
integrated into PM8916 or not. The state of this pad can be checked
with the "USBIN_VALID" interrupt of PM8916.
The "qcom,pm8941-misc" binding exists to expose an "usb_vbus" and/or
"usb_id" interrupt from the PMIC as an extcon device.
Add a &pm8916_usbin node to pm8916.dtsi which can be used as simple
extcon device for devices that are currently lacking a proper charger
driver.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-2-stephan@gerhold.net
While removing the size from the "reg" properties in pm8916.dtsi,
commit bd6429e81010 ("ARM64: dts: qcom: Remove size elements from
pmic reg properties") mistakenly also removed the second register
address for the rtc@6000 device. That one did not represent the size
of the register region but actually the address of the second "alarm"
register region of the rtc@6000 device.
Now there are "reg-names" for two "reg" elements, but there is actually
only one "reg" listed.
Since the DT schema for "qcom,pm8941-rtc" only expects one "reg"
element anyway, just drop the "reg-names" entirely to fix this.
Fixes: bd6429e81010 ("ARM64: dts: qcom: Remove size elements from pmic reg properties")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210928112945.25310-1-stephan@gerhold.net
Add miscellaneous nodes to boot the modem and support post-mortem debug
on SC7280 SoCs.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1631886935-14691-9-git-send-email-sibis@codeaurora.org
This device has a physical matrix keyboard, connected to a GPIO
expander, for which there's still no support yet.
Though, some of the keys are connected to the MSM8998 GPIOs and not
as a matrix, so these can be added.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-4-angelogioacchino.delregno@somainline.org
Add device tree support for the F(x)tec Pro 1 (QX1000) smartphone;
this is a minimal configuration to boot to serial console.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210909123823.368199-1-angelogioacchino.delregno@somainline.org
At the moment, playing audio on Secondary MI2S will just end up getting
stuck, without actually playing any audio. This happens because the wrong
bit clock is configured when playing audio on Secondary MI2S.
The PRI_I2S_CLK (better name: SPKR_I2S_CLK) is used by the SPKR audio mux
block that provides both Primary and Secondary MI2S.
The SEC_I2S_CLK (better name: MIC_I2S_CLK) is used by the MIC audio mux
block that provides Tertiary MI2S. Quaternary MI2S is also part of the
MIC audio mux but has its own clock (AUX_I2S_CLK).
This means that (quite confusingly) the SEC_I2S_CLK is not actually
used for Secondary MI2S as the name would suggest. Secondary MI2S
needs to have the same clock as Primary MI2S configured.
Fix the clock list for the lpass node in the device tree and add
a comment to clarify this confusing naming. With these changes,
audio can be played correctly on Secondary MI2S.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 3761a3618f55 ("arm64: dts: qcom: add lpass node")
Tested-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816181810.2242-1-stephan@gerhold.net
So far there were no interrupts set up for the BMC150 accelerometer
+ magnetometer combo because they were broken for some reason.
It turns out Longcheer L8150 actually has a BMC156 which is very similar
to BMC150, but only has an INT2 pin for the accelerometer part.
This requires some minor changes in the bmc150-accel driver which is now
supported by using the more correct bosch,bmc156_accel compatible.
Unfortunately it looks like even INT2 is not functional on most boards
because the interrupt line is not actually connected to the BMC156.
However, there are two pads next to the chip that can be shorted
to make it work if needed.
While at it, add the missing interrupts for the magnetometer part
and extra BMG160 gyroscope, those seem to work without any problems.
Also correct the magnetometer compatible to bosch,bmc156_magn for clarity
(no functional difference for the magnetometer part).
Tested-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210816123544.14027-1-stephan@gerhold.net
Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.
The bootloader is VERY unpleasant, to get a bootable setup you have to run:
mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img
adb reboot bootloader
// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img
fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-16-konrad.dybcio@somainline.org
Add a node for the APPS SMMU to allow for managing memory access to peripherals
such as the USB controller.
While at it, add iommus property to the USB1 node to make sure its registers can
be accessed, as they seem to be gated by default.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-15-konrad.dybcio@somainline.org
Add SDHCI1/2 nodes for eMMC and uSD card respectively.
Do note that most SM6350 devices seem to come with UFS.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Replaced SM6350_CX with its constant value]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-14-konrad.dybcio@somainline.org
Add nodes required for USB1 to function. SM6350 (thankfully) resuses SDM845 and
SC7180 IP, so no additional code porting is required.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
[bjorn: Renamed dwc3 node "usb"]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-7-konrad.dybcio@somainline.org
Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-6-konrad.dybcio@somainline.org
Add and configure GCC node to allow for referencing GCC-controlled clocks
in other nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-5-konrad.dybcio@somainline.org
Add RPMHCC node to allow for referencing RPMH-controlled clocks in other
nodes.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-4-konrad.dybcio@somainline.org
Add a node for LLCC with SM6350-specific compatible.
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210923162204.21752-3-konrad.dybcio@somainline.org
