IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Valid mask is 0x3FFF, without this patch the following problems were
found:
1) [ 0.938914] Could not find a valid ONFI parameter page, trying
bit-wise majority to recover it
[ 0.947384] ONFI parameter recovery failed, aborting
2) Read with disabled ECC mode was broken.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/3794ffbf-dfea-e96f-1f97-fe235b005e19@sberdevices.ru
Remove the EDO mode support from as the FMC2 controller does not
support the feature.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Cc: stable@vger.kernel.org #v5.4+
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230328155819.225521-2-christophe.kerello@foss.st.com
clang with W=1 reports
drivers/mtd/nand/raw/mxc_nand.c:1602:19: error: unused function
'is_imx51_nfc' [-Werror,-Wunused-function]
static inline int is_imx51_nfc(struct mxc_nand_host *host)
^
drivers/mtd/nand/raw/mxc_nand.c:1607:19: error: unused function
'is_imx53_nfc' [-Werror,-Wunused-function]
static inline int is_imx53_nfc(struct mxc_nand_host *host)
^
These functions are not used, so remove them.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230321114638.1782086-1-trix@redhat.com
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144715.1543926-1-robh@kernel.org
According to the ONFI specification, bit 0 of 'SDR timing mode support'
(bytes 129-130) "shall be 1". That means the NAND supports at least
timing mode 0.
NAND chip Hynix H27U4G8F2GDA-BI (at least) is reading a 0 on this field
which makes nand_choose_best_sdr_timings() return with error and the
probe function to eventually fail.
Given that sdr_timing_modes bit 0 must be 1 by specification, force
it in case the NAND reports it is not set. This is a safe assumption
because the mode 0 is the minimum (safer) set of timings that the
NAND can work with.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230223165104.525852-1-hector.palacios@digi.com
Link: https://lore.kernel.org/linux-mtd/20230310080609.1930869-1-hector.palacios@digi.com
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230310144716.1543995-1-robh@kernel.org
'info_buf' memory is cached and driver polls ECC bit in it. This bit
is set by the NAND controller. If 'usleep_range()' returns before device
sets this bit, 'info_buf' will be cached and driver won't see update of
this bit and will loop forever.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/d4ef0bd6-816e-f6fa-9385-f05f775f0ae2@sberdevices.ru
The continuous read support added recently makes nandsim
unhappy. Indeed, all the supported commands should be re-encoded into
internal commands, so of course there is currently no support for the
commands and patterns needed for continuous reads to work.
I tried to add support for them but nandsim (which is more a tool to
develop/debug upper layers rather than the raw NAND core) suffers from a
big limitation: it's internal parser needs to know what exact operation
is happening when the address cycles are performed. The research is then
sequential from the start up to the address cycles, but does not check
what's coming next even though the information is available. This is a
limitation which is related to the old API used by the core which kind
of forced the controllers to guess what operation was being performed
rather early. Today the core uses a more transparent API called
->exec_op() which no longer requires controller drivers to do any more
guessing, but despite being updated to ->exec_op(), nandsim is still a
bit constrained on this regard and thus cannot handle sequential page
reads because the start sequence beginning is identical to a regular
page read.
If the internal algorithm is updated some day, it should be possible to
make it support sequential page reads by adding something like:
/* Large page devices continuous read page start */
{OPT_LARGEPAGE, {STATE_CMD_READ0, STATE_ADDR_PAGE, STATE_CMD_READSTART,
STATE_CMD_READCACHESEQ | ACTION_CPY, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page continue */
{OPT_LARGEPAGE, {STATE_CMD_READCACHESEQ | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
/* Large page devices continuous read page end */
{OPT_LARGEPAGE, {STATE_CMD_READCACHEEND | ACTION_CPY_NEXT, STATE_DATAOUT,
STATE_READY}},
For now, we just return -EOPNOTSUPP when the core asks controller
drivers if they support the feature in order to prevent any further use
of these opcodes.
Note: This is a hack, ->exec_op() is not supposed to check against the
COMMAND opcodes unless _really_ needed.
Fixes: 003fe4b954 ("mtd: rawnand: Support for sequential cache reads")
Reported-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/linux-mtd/fd34fe55-7f4a-030d-8653-9bb9cf08410d@huawei.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Zhihao Cheng <chengzhihao1@huawei.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/linux-mtd/20230310085452.1368716-1-miquel.raynal@bootlin.com
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230306144141.15360-1-quic_mdalam@quicinc.com
wait_for_completion_timeout() and readl_poll_timeout() don't handle their
return value the same way.
wait_for_completion_timeout() returns 0 on time out (and >0 in all other
cases)
readl_poll_timeout() returns 0 on success and -ETIMEDOUT upon a timeout.
In order for the error handling path to work in both cases, the logic
against wait_for_completion_timeout() needs to be inverted.
Fixes: 48e6633a9f ("mtd: nand: mxic-ecc: Add Macronix external ECC engine support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/beddbc374557e44ceec897e68c4a5d12764ddbb9.1676459308.git.christophe.jaillet@wanadoo.fr
This structure must be zeroed, because it's field 'hw->core' is used as
'parent' in 'clk_core_fill_parent_index()', but it will be uninitialized.
This happens, because when this struct is not zeroed, pointer 'hw' is
"initialized" by garbage, which is valid pointer, but points to some
garbage. So 'hw' will be dereferenced, but 'core' contains some random
data which will be interpreted as a pointer. The following backtrace is
result of dereference of such pointer:
[ 1.081319] __clk_register+0x414/0x820
[ 1.085113] devm_clk_register+0x64/0xd0
[ 1.088995] meson_nfc_probe+0x258/0x6ec
[ 1.092875] platform_probe+0x70/0xf0
[ 1.096498] really_probe+0xc8/0x3e0
[ 1.100034] __driver_probe_device+0x84/0x190
[ 1.104346] driver_probe_device+0x44/0x120
[ 1.108487] __driver_attach+0xb4/0x220
[ 1.112282] bus_for_each_dev+0x78/0xd0
[ 1.116077] driver_attach+0x2c/0x40
[ 1.119613] bus_add_driver+0x184/0x240
[ 1.123408] driver_register+0x80/0x140
[ 1.127203] __platform_driver_register+0x30/0x40
[ 1.131860] meson_nfc_driver_init+0x24/0x30
Fixes: 1e4d3ba668 ("mtd: rawnand: meson: fix the clock")
Signed-off-by: Arseniy Krasnov <AVKrasnov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230227102425.793841-1-AVKrasnov@sberdevices.ru
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/202302101723563685569@zte.com.cn
* parsers: ofpart: add workaround for #size-cells 0
* dt-bindings: partitions: Fix partition node name pattern
* dataflash: remove duplicate SPI ID table
Raw NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND driver changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
* Misc core fixes
SPI NOR driver changes:
* Spansion: Minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3MqwACgkQJWrqGEe9
VoTnsQf/bfzBqf0LbMBU7c+2VUjnE2dgLRssf0WqJB2INvDIAHQ8HKE2rqF6j1G0
wBnJOMf9fRpH6M3k45siNL37HPnacUq8QFZE3B3A3pUewWNtx5ldFrzT1awlsTu8
zIG37pnd2rJ+W3wfDDnNjTqQUfm3sLI7k/B3S8aqJA8i63DFLqih7ju0mgPVT7TX
C1X0VAx8gNMHQ6WqTX53SRZ4Ef9dJAcVwcFhkjHY09Q9VEW56ZlQ7uxyhwYqXjiJ
zDDGfPFhAsfwcykdFI3DtvNRT2bVbJl7N4GvTD8N4Rf+GIuMhVJnUjp5yTkAeEHx
HjXqBSI3ykHimsW7BRtE3HLR4775bA==
=FLt2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- parsers: ofpart: add workaround for #size-cells 0
- dt-bindings: partitions: Fix partition node name pattern
- dataflash: remove duplicate SPI ID table
Raw NAND core changes:
- Check the data only read pattern only once
- Prepare the late addition of supported operation checks
- Support for sequential cache reads
- Fix nand_chip kdoc
Raw NAND driver changes:
- Fsl_elbc: Propagate HW ECC settings to HW
- Marvell: Add missing layouts
- Pasemi: Don't use static data to track per-device state
- Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
- tmio_nand: Remove driver
- vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
- Add support for AllianceMemory AS5F34G04SND
- Macronix: use scratch buffer for DMA operation
NAND ECC changes:
- Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
- Misc core fixes
SPI NOR driver changes:
- Spansion: Minor fixes"
* tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (33 commits)
mtd: parsers: ofpart: add workaround for #size-cells 0
mtd: rawnand: sunxi: Precompute the ECC_CTL register value
mtd: rawnand: sunxi: Embed sunxi_nand_hw_ecc by value
mtd: rawnand: sunxi: Update OOB layout to match hardware
mtd: spi-nor: Sort headers alphabetically
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986
dt-bindings: mtd: Split ECC engine with rawnand controller
mtd: rawnand: fsl_elbc: Propagate HW ECC settings to HW
mtd: spinand: Add support for AllianceMemory AS5F34G04SND
dt-bindings: mtd: partitions: Fix partition node name pattern
mtd: spi-nor: Create macros to define chip IDs and geometries
mtd: spi-nor: spansion: Make CFRx reg fields generic
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: core: fix implicit declaration warning
mtd: spinand: macronix: use scratch buffer for DMA operation
mtd: rawnand: Fix nand_chip kdoc
mtd: rawnand: vf610_nfc: use regular comments for functions
mtd: rawnand: Support for sequential cache reads
...
The value computed by this function never changes for a given chip.
Compute the whole register value once up front, instead of every time
the ECC engine is enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-4-samuel@sholland.org
The sunxi_nand_hw_ecc object is not shared, and it has the same lifetime
as the sunxi_nand_chip which points to it, so we can embed it in the
outer structure instead of using a pointer. This removes an unnecessary
memory allocation and simplifies the error handling code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-3-samuel@sholland.org
When using the hardware ECC engine, the OOB data is made available in
the NFC_REG_USER_DATA registers, as one 32-bit word per ECC step. Any
additional bytes are only accessible through raw reads and software
descrambling. For efficiency, and to match the vendor driver, ignore
these extra bytes when using hardware ECC.
Note that until commit 34569d8695 ("mtd: rawnand: sunxi: Fix the size
of the last OOB region"), this extra free area was reported with length
zero, so this is not a functional change for any stable kernel user.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-2-samuel@sholland.org
It is possible that current chip->ecc.engine_type value does not match to
configured HW value (if HW ECC checking and generating is enabled or not).
This can happen with old U-Boot bootloader version which either does not
initialize NAND (and let it in some default unusable state) or initialize
NAND with different parameters than what is specified in kernel DTS file.
So if kernel chose to use some chip->ecc.engine_type settings (e.g. from
DTS file) then do not depend on bootloader HW configuration and configures
HW ECC settings according to chip->ecc.engine_type value.
BR_DECC must be set to BR_DECC_CHK_GEN when HW is doing ECC (both
generating and checking), or to BR_DECC_OFF when HW is not doing ECC.
This change fixes usage of SW ECC support in case bootloader explicitly
enabled HW ECC support and kernel DTS file has specified to use SW ECC.
(Of course this works only in case when NAND is not a boot device and both
bootloader and kernel are loaded from different location, e.g. FLASH NOR.)
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230128134111.32559-1-pali@kernel.org
The mx35lf1ge4ab_get_eccsr() function uses an SPI DMA operation to
read the eccsr, hence the buffer should not be on stack. Since commit
380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
the kernel emmits a warning and blocks such operations.
Use the scratch buffer to get eccsr instead of trying to directly read
into a stack-allocated variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y8i85zM0u4XdM46z@makrotopia.org
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These comments are not quite in kernel-doc format and they don't need
to be, so just use "/*" comment markers for them. This prevents these
kernel-doc warnings:
drivers/mtd/nand/raw/vf610_nfc.c:210: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Read accessor for internal SRAM buffer
drivers/mtd/nand/raw/vf610_nfc.c:245: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Write accessor for internal SRAM buffer
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230113064004.24391-1-rdunlap@infradead.org
Add support for sequential cache reads for controllers using the generic
core helpers for their fast read/write helpers.
Sequential reads may reduce the overhead when accessing physically
continuous data by loading in cache the next page while the previous
page gets sent out on the NAND bus.
The ONFI specification provides the following additional commands to
handle sequential cached reads:
* 0x31 - READ CACHE SEQUENTIAL:
Requires the NAND chip to load the next page into cache while keeping
the current cache available for host reads.
* 0x3F - READ CACHE END:
Tells the NAND chip this is the end of the sequential cache read, the
current cache shall remain accessible for the host but no more
internal cache loading operation is required.
On the bus, a multi page read operation is currently handled like this:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR+tRR) -- DATA1_IN
00 -- ADDR2 -- 30 -- WAIT_RDY (tR+tRR) -- DATA2_IN
00 -- ADDR3 -- 30 -- WAIT_RDY (tR+tRR) -- DATA3_IN
Sequential cached reads may instead be achieved with:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR) -- \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA1_IN \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA2_IN \
3F -- WAIT_RDY (tRCBSY+tRR) -- DATA3_IN
Below are the read speed test results with regular reads and
sequential cached reads, on NXP i.MX6 VAR-SOM-SOLO in mapping mode with
a NAND chip characterized with the following timings:
* tR: 20 µs
* tRCBSY: 5 µs
* tRR: 20 ns
and the following geometry:
* device size: 2 MiB
* eraseblock size: 128 kiB
* page size: 2 kiB
============= Normal read @ 33MHz =================
mtd_speedtest: eraseblock read speed is 15633 KiB/s
mtd_speedtest: page read speed is 15515 KiB/s
mtd_speedtest: 2 page read speed is 15398 KiB/s
===================================================
========= Sequential cache read @ 33MHz ===========
mtd_speedtest: eraseblock read speed is 18285 KiB/s
mtd_speedtest: page read speed is 15875 KiB/s
mtd_speedtest: 2 page read speed is 16253 KiB/s
===================================================
We observe an overall speed improvement of about 5% when reading
2 pages, up to 15% when reading an entire block. This is due to the
~14us gain on each additional page read (tR - (tRCBSY + tRR)).
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-4-miquel.raynal@bootlin.com
Add an empty envelope just to show how to add additional checks for new
operations. This is going to be used for sequential cached reads, which
require the page size to be known (and the discovery to be over), hence
the "late" designation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-3-miquel.raynal@bootlin.com
Instead of checking if a pattern is supported each time we need it,
let's create a bitfield that only the core would be allowed to fill at
startup time. The core and the individual drivers may then use it in
order to check what operation they should use. This bitfield is supposed
to grow over time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-2-miquel.raynal@bootlin.com
With the TMIO MFD drivers gone, the NAND support is also
obsolete and can be removed.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Up to now the pasemi nand driver only supported a single device
instance. However the check for that was racy because two parallel calls
of pasemi_nand_probe() could pass the check
if (pasemi_nand_mtd)
return -ENODEV;
before any of them assigns a non-NULL value to it.
So rework the driver to make use of per-device driver data.
As an intended side effect the driver can bind more than one device and
also gets rid of the check
if (!pasemi_nand_mtd)
return 0;
in the remove callback that could only ever trigger after the above race
happened.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230102124051.1508424-1-u.kleine-koenig@pengutronix.de
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-4-samuel@sholland.org
If a chip fails to initialize, we need to clean up any chips that were
already initialized/registered.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-2-samuel@sholland.org
A missing layouts were added to the driver to support NAND flashes
with ECC layouts of 12 or 16 with page sized of 2048, 4096 or 8192.
Usually theses are rare layouts, but in Marvell AC5 driver, the ECC
level is set according to the spare area, so we may use these layouts
more frequently.
Signed-off-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221216162715.3230766-1-vadym.kochan@plvision.eu
* Fix refcount error in del_mtd_device()
* Fix possible resource leak in init_mtd()
* Set ROOT_DEV for partitions marked as rootfs in DT
* Describe marking rootfs partitions in the bindings
* Fix device name leak when register device failed in add_mtd_device()
* Try to find OF node for every MTD partition
* simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
* pxa2xx-flash maps: fix memory leak in probe
* BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
* lpddr2_nvm: Fix possible null-ptr-deref
* inftlcore: fix repeated words in comments
* lart: remove driver
* tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
* mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter to after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
* Fixed-partitions: Fix 'sercomm,scpart-id' schema
* Standardize the style in the examples
* Drop object types when referencing other files
* Argue in favor of keeping additionalProperties set to true
* NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
* Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
* Physmap: Reuse the generic definitions
* SPI-NOR: Drop common properties
* Sunxi-nand: Add an example to validate the bindings
* Onenand: Mention the expected node name
* Ingenic: Mark partitions in the controller node as deprecated
* NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
* Remove useless file about partitions
* Clarify all partition subnodes
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOOBbQACgkQJWrqGEe9
VoRB7wf9EY8IeRhumaeN9WT+VrmPxGOu61m/eilUK4xvgj6JX/yhYo/kKW9eEp+o
5I8JLimG6uo7rZNlbixGMbHd41aTu9MplLrTA42nzGadl3w4D8p9c1ic6sEiv7SI
qgnAbzq3FLUPDLLDV0IfrMQvsQgJkv3b+r8ShPt9uJy3cmnKQzOvIhs43wwLnOXp
NPiMbVjpS4FAmNvG7nI0xfcBLO/eFaTuQc+UyfP2SwkVIAN5xfUAwOPOHZWBstmR
zhJlHSFJWrg+J9T9bsRW7D5q/MVxqNsMH589c9aXHNqzgzZs2FTopDUf6cWwHr0f
2Ssot2naIdvU+eLGA12hDuUDDoRwKA==
=Igti
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Fix refcount error in del_mtd_device()
- Fix possible resource leak in init_mtd()
- Set ROOT_DEV for partitions marked as rootfs in DT
- Describe marking rootfs partitions in the bindings
- Fix device name leak when register device fails in add_mtd_device()
- Try to find OF node for every MTD partition
- simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
- pxa2xx-flash maps: fix memory leak in probe
- BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
- lpddr2_nvm: Fix possible null-ptr-deref
- inftlcore: fix repeated words in comments
- lart: remove driver
- tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
- mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
- Fixed-partitions: Fix 'sercomm,scpart-id' schema
- Standardize the style in the examples
- Drop object types when referencing other files
- Argue in favor of keeping additionalProperties set to true
- NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
- Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
- Physmap: Reuse the generic definitions
- SPI-NOR: Drop common properties
- Sunxi-nand: Add an example to validate the bindings
- Onenand: Mention the expected node name
- Ingenic: Mark partitions in the controller node as deprecated
- NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
- Remove useless file about partitions
- Clarify all partition subnodes
SPI NOR core changes:
- Add support for flash reset using the dt reset-gpios property.
- Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
- Bypass zero erase size in spi_nor_find_best_erase_type().
- Fix select_uniform_erase to skip 0 erase size
- Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described
solely by the flash's SFDP tables.
- Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
- Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP
discoverable.
SPI NOR manufacturer drivers changes:
- Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
- Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
- Micron - ST: Enable locking for mt25qu256a.
- Winbond: Add support for W25Q512NW-IQ.
- ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
- Drop obsolete dependencies on COMPILE_TEST
- MAINTAINERS: rectify entry for MESON NAND controller bindings
- Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
- marvell: Enable NFC/DEVBUS arbiter
- gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
- mpc5121: Replace NO_IRQ by 0
- lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
- lpc32xx_mlc: Switch to using pm_ptr()
- cadence: Support 64-bit slave dma interface
- rockchip: Describe rk3128-nfc in the bindings
- brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
- winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification"
* tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: rawnand: Drop obsolete dependencies on COMPILE_TEST
mtd: maps: pxa2xx-flash: fix memory leak in probe
mtd: core: Fix refcount error in del_mtd_device()
mtd: spi-nor: add SFDP fixups for Quad Page Program
mtd: spi-nor: issi: is25wp256: Init flash based on SFDP
mtd: spi-nor: winbond: add support for W25Q512NW-IQ
mtd: spi-nor: micron-st: Enable locking for mt25qu256a
mtd: spi-nor: Fix the number of bytes for the dummy cycles
mtd: spi-nor: gigadevice: gd25q256: replace gd25q256_default_init with gd25q256_post_bfpt
mtd: spi-nor: Fix formatting in spi_nor_read_raw() kerneldoc comment
mtd: spi-nor: sysfs: print JEDEC ID for generic flash driver
mtd: spi-nor: add generic flash driver
mtd: spi-nor: fix select_uniform_erase to skip 0 erase size
mtd: spi-nor: move function declaration out of sfdp.h
mtd: spi-nor: remember full JEDEC flash ID
mtd: spi-nor: sysfs: hide manufacturer if it is not set
mtd: spi-nor: hide jedec_id sysfs attribute if not present
mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
mtd: rawnand: marvell: Enable NFC/DEVBUS arbiter
mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
...
-----BEGIN PGP SIGNATURE-----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=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOGGfIACgkQJWrqGEe9
VoSZVQgAmew5RtMegFus/AXflUsGYCvZKfV1LVnxmSoGIKBrJr3yjzh6mFuLyzaP
qt2KljEJ4dblk2M3efosX5YeAkz7A7evm218NHGeKWHMPCDimSE1ptAyBhhMmsVi
cgCgu3LXh369dK9OAm7ZVR4hOdDuK5rpYIcXA4mUh0yqiFxfxsuuNY7QBDVrN+qt
SNmZkTBbCgGRxo7RRanN2ljnSm31p6TyhngUDKG89puMka9gGA9yWLbWFDpwM5SS
L0Tr2ZOHctzz/X/1s2yPcnN6ZPpqsc1wLnGyLOWlhkm7oo7aiT59rlHj9GHbp82h
7lXf7MeWxSNSVr9PMHHUR7XDqlLaOw==
=aOZ+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.2' into mtd/next
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221124115946.5edb771c@endymion.delvare
These cases were done with this Coccinelle:
@@
expression H;
expression L;
@@
- (get_random_u32_below(H) + L)
+ get_random_u32_inclusive(L, H + L - 1)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- + E
- - E
)
@@
expression H;
expression L;
expression E;
@@
get_random_u32_inclusive(L,
H
- - E
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- - E
+ F
- + E
)
@@
expression H;
expression L;
expression E;
expression F;
@@
get_random_u32_inclusive(L,
H
- + E
+ F
- - E
)
And then subsequently cleaned up by hand, with several automatic cases
rejected if it didn't make sense contextually.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The CN9130 SoC (an ARMADA 8K type) has both a NAND Flash Controller and
a generic local bus controller (Device Bus Controller) that share common
pins.
With a board design that incorporates both a NAND flash and uses
the Device Bus (in our case for an SRAM) accessing the Device Bus device
fails unless the NfArbiterEn bit is set. Setting the bit enables
arbitration between the Device Bus and the NAND flash.
Since there is no obvious downside in enabling this for designs that
don't require arbitration, we always enable it.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221109231325.7714-1-hamish.martin@alliedtelesis.co.nz
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_slc.c:318:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
318 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 6b923db286 ("mtd: rawnand: lpc32xx_slc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-2-geert@linux-m68k.org
The switch to using the gpiod API removed the last user of
lpc32xx_wp_disable() outside #ifdef CONFIG_PM, causing build failures if
CONFIG_PM=n:
drivers/mtd/nand/raw/lpc32xx_mlc.c:380:13: error: ‘lpc32xx_wp_disable’ defined but not used [-Werror=unused-function]
380 | static void lpc32xx_wp_disable(struct lpc32xx_nand_host *host)
| ^~~~~~~~~~~~~~~~~~
Fix this by switching from #ifdef CONFIG_PM to pm_ptr(), increasing
compile-coverage as a side-effect.
Reported-by: noreply@ellerman.id.au
Fixes: 782e32a990 ("mtd: rawnand: lpc32xx_mlc: switch to using gpiod API")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221027131028.3838303-1-geert@linux-m68k.org
OMAP2 OneNAND driver uses gpmc_omap_onenand_set_timings() provided by
OMAP_GPMC driver, so the latter cannot be module if OneNAND driver is
built-in:
/usr/bin/arm-linux-gnueabi-ld: drivers/mtd/nand/onenand/onenand_omap2.o: in function `omap2_onenand_probe':
onenand_omap2.c:(.text+0x520): undefined reference to `gpmc_omap_onenand_set_timings'
The OMAP_GPMC is also a runtime dependency.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 854fd9209b ("memory: omap-gpmc: Allow building as a module")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221107091520.127053-1-krzysztof.kozlowski@linaro.org
The compiler is not smart enough to notice that it's impossible for
them to be actually used uninitialized. Which exact variables trip
here varies depending on random surrounding code; none triggered in
6.1-rc1 but 6.1-rc2 fails on three of these five, despite variables
declared in the very same line having identical flow.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221024092026.42123-1-kilobyte@angband.pl
With use_codeword_fixup enabled, any return from
mtd_device_parse_register gets overwritten. Aside from the clear bug, this
is also problematic as a parser can EPROBE_DEFER and because this is not
correctly handled, the nand is never rescanned later in the bootup
process.
An example of this problem is when smem requires additional time to be
probed and nandc use qcomsmempart as parser. Parser will return
EPROBE_DEFER but in the current code this ret gets overwritten by
qcom_nand_host_parse_boot_partitions and qcom_nand_host_init_and_register
return 0.
Correctly handle the return code from mtd_device_parse_register so that
any error from this function is not ignored.
Fixes: 862bdedd7f ("mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221021165304.19991-1-ansuelsmth@gmail.com
Winbond uses 3 bytes to identify flash: vendor_id, dev_id_0, dev_id_1,
but current driver uses only first 2 bytes of it for devices
identification. As result Winbond W25N02KV flash (id_bytes: EF, AA, 22)
is identified as W25N01GV (id_bytes: EF, AA, 21).
Fix this by adding missed identification bytes.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221010105110.446674-1-mikhail.kshevetskiy@iopsys.eu
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/4e3ca3e0077ea124ea210c312e6e620f0f9e8bca.1665034065.git.christophe.leroy@csgroup.eu
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org
Fixes: 7a08dbaedd ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops")
Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Cc: stable@vger.kernel.org
Fixes: d7d9f8ec77 ("mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220926084456.98160-1-zhangqilong3@huawei.com
The 'chip_np' returned by of_get_next_child() with refcount decremented,
of_node_put() need be called in error path to decrease the refcount.
Fixes: bfc618fcc3 ("mtd: rawnand: intel: Read the chip-select line from the correct OF node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220924131010.957117-1-yangyingliang@huawei.com
The prandom_bytes() function has been a deprecated inline wrapper around
get_random_bytes() for several releases now, and compiles down to the
exact same code. Replace the deprecated wrapper with a direct call to
the real function. This was done as a basic find and replace.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # powerpc
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than truncate a 32-bit value to a 16-bit value or an 8-bit value,
simply use the get_random_{u8,u16}() functions, which are faster than
wasting the additional bytes from a 32-bit value. This was done by hand,
identifying all of the places where one of the random integer functions
was used in a non-32-bit context.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rather than incurring a division or requesting too many random bytes for
the given range, use the prandom_u32_max() function, which only takes
the minimum required bytes from the RNG and avoids divisions. This was
done mechanically with this coccinelle script:
@basic@
expression E;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
typedef u64;
@@
(
- ((T)get_random_u32() % (E))
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ((E) - 1))
+ prandom_u32_max(E * XXX_MAKE_SURE_E_IS_POW2)
|
- ((u64)(E) * get_random_u32() >> 32)
+ prandom_u32_max(E)
|
- ((T)get_random_u32() & ~PAGE_MASK)
+ prandom_u32_max(PAGE_SIZE)
)
@multi_line@
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
identifier RAND;
expression E;
@@
- RAND = get_random_u32();
... when != RAND
- RAND %= (E);
+ RAND = prandom_u32_max(E);
// Find a potential literal
@literal_mask@
expression LITERAL;
type T;
identifier get_random_u32 =~ "get_random_int|prandom_u32|get_random_u32";
position p;
@@
((T)get_random_u32()@p & (LITERAL))
// Add one to the literal.
@script:python add_one@
literal << literal_mask.LITERAL;
RESULT;
@@
value = None
if literal.startswith('0x'):
value = int(literal, 16)
elif literal[0] in '123456789':
value = int(literal, 10)
if value is None:
print("I don't know how to handle %s" % (literal))
cocci.include_match(False)
elif value == 2**32 - 1 or value == 2**31 - 1 or value == 2**24 - 1 or value == 2**16 - 1 or value == 2**8 - 1:
print("Skipping 0x%x for cleanup elsewhere" % (value))
cocci.include_match(False)
elif value & (value + 1) != 0:
print("Skipping 0x%x because it's not a power of two minus one" % (value))
cocci.include_match(False)
elif literal.startswith('0x'):
coccinelle.RESULT = cocci.make_expr("0x%x" % (value + 1))
else:
coccinelle.RESULT = cocci.make_expr("%d" % (value + 1))
// Replace the literal mask with the calculated result.
@plus_one@
expression literal_mask.LITERAL;
position literal_mask.p;
expression add_one.RESULT;
identifier FUNC;
@@
- (FUNC()@p & (LITERAL))
+ prandom_u32_max(RESULT)
@collapse_ret@
type T;
identifier VAR;
expression E;
@@
{
- T VAR;
- VAR = (E);
- return VAR;
+ return E;
}
@drop_var@
type T;
identifier VAR;
@@
{
- T VAR;
... when != VAR
}
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: KP Singh <kpsingh@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz> # for ext4 and sbitmap
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com> # for drbd
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Heiko Carstens <hca@linux.ibm.com> # for s390
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmNAOvwACgkQJWrqGEe9
VoRNwQf9EqZu7zW/kWBi7cN9koCk/5YuKeCQi9KJhCf4MC9928BdEy5wwRYPkZPJ
N1rTS4Fdx+nLDpULqcE9KYDSJZM09dGEHN7sFYwJR+zKRpBV5awfDvV8gWZp1Afk
MLtC+AWO1GkJ/5V0Qmw0RX+0rtM9v+QpH25+nvJImBKt7iTfperpBDmO7S7htxhN
xPKLj8A8Ns2LR/JirwHT2DRLwe/1UJwLxNfL/yzyWxekaqmRUNz2rYSQ56ZJAbc4
D9jotFRwdpaMIKkGuruYed2gM7rgbtzSaGLZNYuHzcLMKFocH9vLL7D3EAbovoDL
D1l1saZDYsYpXkVwM4uKPWR/B8lgcg==
=DvSB
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.1' into mtd/next
Raw NAND core changes:
* Replace of_gpio_named_count() by gpiod_count()
- Remove misguided comment of nand_get_device()
- bbt: Use the bitmap API to allocate bitmaps
Raw NAND controller drivers changes:
* Meson:
- Stop supporting legacy clocks
- Refine resource getting in probe
- Convert bindings to yaml
- Fix clock handling and update the bindings accordingly
- Fix bit map use in meson_nfc_ecc_correct()
* bcm47xx:
- Fix spelling typo in comment
* STM32 FMC2:
- Switch to using devm_fwnode_gpiod_get()
- Fix dma_map_sg error check
* Cadence:
- Remove an unneeded result variable
* Marvell:
- Fix error handle regarding dma_map_sg
* Orion:
- Use devm_clk_get_optional()
* Cafe:
- Use correct function name in comment block
* Atmel:
- Unmap streaming DMA mappings
* Arasan:
- Stop using 0 as NULL pointer
* GPMI:
- Fix typo 'the the' in comment
* BRCM:
- Add individual glue driver selection
- Move Kconfig to driver folder
* FSL: Fix none ECC mode
* Intel:
- Use devm_platform_ioremap_resource_byname()
- Remove unused clk_rate member from struct ebu_nand
- Remove unused nand_pa member from ebu_nand_cs
- Don't re-define NAND_DATA_IFACE_CHECK_ONLY
- Remove undocumented compatible string
- Fix compatible string in the bindings
- Read the chip-select line from the correct OF node
- Fix maximum chip select value in the bindings
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
meson NFC driver only uses common clock interfaces, which triggers kernel test
robot errors when using legacy clocks with HAVE_LEGACY_CLK on.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
[miquel.raynal@bootlin.com: Rephrase the commit log]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-6-liang.yang@amlogic.com
simply use devm_platform_ioremap_resource_byname() instead of two steps:
res = platform_get_resource(pdev, IORESOURCE_MEM, 0) and
reg_base = devm_ioremap_resource(dev, res)
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-4-liang.yang@amlogic.com
EMMC and NAND have the same clock control register named 'SD_EMMC_CLOCK'
which is defined in EMMC port internally. bit0~5 of 'SD_EMMC_CLOCK' is
the divider and bit6~7 is the mux for fix pll and xtal. At the beginning,
a common MMC and NAND sub-clock was discussed and planed to be implemented
as NFC clock provider, but now this series of patches of a common MMC and
NAND sub-clock are never being accepted. the reasons for giving up are:
1. EMMC and NAND, which are mutually exclusive anyway
2. coupling the EMMC and NAND.
3. it seems that a common MMC and NAND sub-clock is over engineered.
and let us see the link fot more information:
https://lore.kernel.org/all/20220121074508.42168-5-liang.yang@amlogic.com
so The meson nfc can't work now, let us rework the clock.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220907080405.28240-3-liang.yang@amlogic.com
Return the value cadence_nand_set_access_width16() directly instead of
storing it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220901074555.313266-1-ye.xingchen@zte.com.cn
After commit 8cba323437 ("mtd: rawnand: protect access to rawnand devices
while in suspend"), it will wait while in suspend rather than returning
errors. So remove the misguided comment about return value.
Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220819021846.2924539-1-chenxiaosong2@huawei.com
Every dma_map_single() call should have its dma_unmap_single() counterpart,
because the DMA address space is a shared resource and one could render the
machine unusable by consuming all DMA addresses.
Link: https://lore.kernel.org/lkml/13c6c9a2-6db5-c3bf-349b-4c127ad3496a@axentia.se/
Cc: stable@vger.kernel.org
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Alexander Dahl <ada@thorsis.com>
Reported-by: Peter Rosin <peda@axentia.se>
Tested-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220728074014.145406-1-tudor.ambarus@microchip.com
The meson_nfc_ecc_correct() function accidentally does a right shift
instead of a left shift so it only works for BIT(0). Also use
BIT_ULL() because "correct_bitmap" is a u64 and we want to avoid
shift wrapping bugs.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YuI2zF1hP65+LE7r@kili
Allow each platform to define a dedicated Kconfig entry for its glue
driver such that we can decide on a per-platfomr basis whether to build
it or not. This allows for a finer grained control over the resulting
kernel image or set of modules.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-3-f.fainelli@gmail.com
In preparation for allowing each of the brcmnand stub to be built
separately, move the Kconfig entry to the driver folder.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220711222323.4048197-2-f.fainelli@gmail.com
Extend struct mtd_req_stats with two new fields holding the number of
corrected bitflips and uncorrectable errors detected during a read
operation. This is a prerequisite for ultimately passing those counters
to user space, where they can be useful to applications for making
better-informed choices about moving data around.
Unlike 'max_bitflips' (which is set - in a common code path - to the
return value of a function called while the MTD device's mutex is held),
these counters have to be maintained in each MTD driver which defines
the '_read_oob' callback because the statistics need to be calculated
while the MTD device's mutex is held.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-4-kernel@kempniu.pl
As the 'stats' field in struct mtd_oob_ops is used in conditional
expressions, ensure it is always zero-initialized in all such structures
to prevent random stack garbage from being interpreted as a pointer.
Strictly speaking, this problem currently only needs to be fixed for
struct mtd_oob_ops structures subsequently passed to mtd_read_oob().
However, this commit goes a step further and makes all instances of
struct mtd_oob_ops in the tree zero-initialized, in hope of preventing
future problems, e.g. if struct mtd_req_stats gets extended with write
statistics at some point.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220629125737.14418-3-kernel@kempniu.pl
Commit f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work") added
support for specifying ECC mode via DTS and skipping autodetection.
But it broke explicit specification of HW ECC mode in DTS as correct
settings for HW ECC mode are applied only when NONE mode or nothing was
specified in DTS file.
Also it started aliasing NONE mode to be same as when ECC mode was not
specified and disallowed usage of ON_DIE mode.
Fix all these issues. Use autodetection of ECC mode only in case when mode
was really not specified in DTS file by checking that ecc value is invalid.
Set HW ECC settings either when HW ECC was specified in DTS or it was
autodetected. And do not fail when ON_DIE mode is set.
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220707184328.3845-1-pali@kernel.org
Switch from open-coded platform_get_resource_byname() and
devm_ioremap_resource() to devm_platform_ioremap_resource_byname() where
possible to simplify the code.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-9-martin.blumenstingl@googlemail.com
NAND_DATA_IFACE_CHECK_ONLY is already defined in
include/linux/mtd/rawnand.h which is also included by the driver. Drop
the re-definition from the intel-nand-controller driver.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-6-martin.blumenstingl@googlemail.com
The "intel,nand-controller" compatible string is not part of the
dt-bindings. Remove it from the driver as it's not supposed to be used
without any documentation for it.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220702231227.1579176-5-martin.blumenstingl@googlemail.com
* Dynamic partition support
* Fix deadlock in sm_ftl
* Various refcount fixes in maps, partitions and parser code
* Integer overflow fixes in mtdchar
* Support for Sercomm partitions
NAND driver changes:
* Clockrate fix for arasan
* Add ATO25D1GA support
* Double free fix for meson driver
* Fix probe/remove methods in cafe NAND
* Support unprotected spare data pages in qcom_nandc
SPI NOR core changes:
* move SECT_4K_PMC flag out of the core as it's a vendor specific flag
* s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
* do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
* track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
* esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
* micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
* spansion: Add s25hl-t/s25hs-t IDs and fixups.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEdgfidid8lnn52cLTZvlZhesYu8EFAmLthF4ACgkQZvlZhesY
u8FCkQ//QNJE67mHMWakQRAgjrJ7S8XAbr3BhWLAo/jKxWq0dp+UmPbR+ioia9bv
wCgrKhHySdsHfyIsuSe+6oSfs0cqGxOo9o8ldW0fygcgX015/FQu72KEDuIQssl8
fK2x9IPiwB9a4gwJq8K8DdIrmQtzi4pu3L+xjylrhlJ+7P7pcjGsUSY8kIuW0FI9
1MD8SawOdtoch8STORnRop9XgPbFMJGx3/Oa7eUm9l6YDbKdtO+b2PJELfReXaHy
zSTtvG+uP7SOSG7vEVgap76GaXrOklmsiPN62dp+Rk20aqU6DzpGFTdlG8TMMrMc
x3CG4SyRbtCrb9UhZf5V/LMWMVZrRyuXUxTdNmFCAnTjONXq0UG6HEb4lrOxc7s7
Az286Ycc2DXCwDrqa50LWAw2nP8JKoRQiMU4Q/9f1UIpIpA7wSrwwtzX/q5LqbEd
H+q6UOClw92nJZcimLbdyjo9Pauj8Cus76nuasSxSVIC1sWMKg2Y/vOnCgD8SQMj
ISqO/3A7Dr2xUvKJmM7H3sfyyUWehnYjD/nNc1TOjWzOxAQOlOpMdY8+5I/9Pc0Y
q9NiCNFiBht14Fc/klWsg8xtNMpPAi7pua1F04meK6Z//9uUbiiN5el/snEQ1uCF
8o3ILFVpCgHIv2kmjGBBwxzXA9W6V1z/qTundQHJoSRc9DS8VAQ=
=eBd9
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Dynamic partition support
- Fix deadlock in sm_ftl
- Various refcount fixes in maps, partitions and parser code
- Integer overflow fixes in mtdchar
- Support for Sercomm partitions
NAND driver changes:
- Clockrate fix for arasan
- Add ATO25D1GA support
- Double free fix for meson driver
- Fix probe/remove methods in cafe NAND
- Support unprotected spare data pages in qcom_nandc
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific
flag
- s/addr_width/addr_nbytes/g: address width means the number of IO
lines used for the address, whereas in the code it is used as the
number of address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP
parsing time we should not change members of struct spi_nor, but
instead fill members of struct spi_nor_flash_parameters which could
later on be used by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it
to allow flashes that support FSR to work even when attached to
such SPI controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups"
* tag 'mtd/for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (53 commits)
mtd: core: check partition before dereference
mtd: spi-nor: fix spi_nor_spimem_setup_op() call in spi_nor_erase_{sector,chip}()
mtd: spi-nor: spansion: Add s25hl-t/s25hs-t IDs and fixups
mtd: spi-nor: spansion: Add local function to discover page size
mtd: spi-nor: core: Track flash's internal address mode
mtd: spi-nor: core: Return error code from set_4byte_addr_mode()
mtd: spi-nor: Do not change nor->addr_nbytes at SFDP parsing time
mtd: spi-nor: core: Shrink the storage size of the flash_info's addr_nbytes
mtd: spi-nor: s/addr_width/addr_nbytes
mtd: spi-nor: esmt: Use correct name of f25l32qa
mtd: spi-nor: micron-st: Skip FSR reading if SPI controller does not support it
MAINTAINERS: Use my kernel.org email
mtd: rawnand: arasan: Fix clock rate in NV-DDR
mtd: rawnand: arasan: Update NAND bus clock instead of system clock
mtd: core: introduce of support for dynamic partitions
dt-bindings: mtd: partitions: add additional example for qcom,smem-part
dt-bindings: mtd: partitions: support label/name only partition
mtd: spi-nor: move SECT_4K_PMC special handling
mtd: dataflash: Add SPI ID table
mtd: hyperbus: rpc-if: Fix RPM imbalance in probe error path
...
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmLjfRkACgkQS1VPR6WN
FOn9BQf/bCkxIpGY64RoV5CLNuDj+d4nAlqa7YaL7ftkHvgpEJd8x540dWxYnTsW
FzOReFnZRtb4yjFAlOmYyqYhFuhWjDV4fmjWkeZwLqNM4GN80wKF3btf4V06gp5S
Levjgmqiz/qBsrz9QYdDcB8YLVMOgInQLV8fNrBaG2oLAdskrzXaAukzkmvwnrHM
iVQFZVLfP20qJOnoeahGJ7QObx2A8E9B2APXl9lOCTiVwuDwbFhkKQ3Vf7EqeOS1
BTwSRplAia/JvV+AsESQIL7C4I/xjDbIQ/UD9XsWD7yHo7f8FNi0fxrQ+j8HSnz9
49Ho+csCSV3MMqwnzQT6ciDzzd2zag==
=MJ3w
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.20' into mtd/next
SPI NOR core changes:
- move SECT_4K_PMC flag out of the core as it's a vendor specific flag
- s/addr_width/addr_nbytes: address width means the number of IO lines
used for the address, whereas in the code it is used as the number of
address bytes.
- do not change nor->addr_nbytes at SFDP parsing time. At the SFDP parsing
time we should not change members of struct spi_nor, but instead fill
members of struct spi_nor_flash_parameters which could later on be used
by the callers.
- track flash's internal address mode so that we can use 4B opcodes
together with opcodes that don't have a 4B opcode correspondent.
SPI NOR manufacturer drivers changes:
- esmt: Rename "f25l32qa" flash name to "f25l32qa-2s".
- micron-st: Skip FSR reading if SPI controller does not support it to
allow flashes that support FSR to work even when attached to such SPI
controllers.
- spansion: Add s25hl-t/s25hs-t IDs and fixups.
06781a5026 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b120612206 ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain@gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-3-amit.kumar-mahapatra@xilinx.com
In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable@vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220628154824.12222-2-amit.kumar-mahapatra@xilinx.com
there is an unexpected word 'is' in the comments that need to be dropped
file: drivers/mtd/nand/raw/sm_common.c
line: 55
/* NOTE: This layout is is not compatabable with SmartMedia, */
changed to:
/* NOTE: This layout is not compatabable with SmartMedia, */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220622160511.11679-1-jiangjian@cdjrlc.com
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.
The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.
Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.
Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.
On user read/write the page is checked and if it's a boot page the
correct layout is used.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220616001835.24393-3-ansuelsmth@gmail.com
The DEVICE_BUSY_TIMEOUT value is described in the Reference Manual as:
| Timeout waiting for NAND Ready/Busy or ATA IRQ. Used in WAIT_FOR_READY
| mode. This value is the number of GPMI_CLK cycles multiplied by 4096.
So instead of multiplying the value in cycles with 4096, we have to
divide it by that value. Use DIV_ROUND_UP to make sure we are on the
safe side, especially when the calculated value in cycles is smaller
than 4096 as typically the case.
This bug likely never triggered because any timeout != 0 usually will
do. In my case the busy timeout in cycles was originally calculated as
2408, which multiplied with 4096 is 0x968000. The lower 16 bits were
taken for the 16 bit wide register field, so the register value was
0x8000. With 2970bf5a32 ("mtd: rawnand: gpmi: fix controller timings
setting") however the value in cycles became 2384, which multiplied
with 4096 is 0x950000. The lower 16 bit are 0x0 now resulting in an
intermediate timeout when reading from NAND.
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220614083138.3455683-1-s.hauer@pengutronix.de
This reverts commit 3380557fc7.
It turned out this "4-byte" ID might have been an honest mistake.
Regrettably, the chip Andreas has might be a counterfeit or is
damaged in some other way and shouldn't have ended up in a router.
Andreas reported his chip is returning just four bytes:
"98 f1 80 15 00 00 00 00".
However, according to Kioxia/Toshiba's datasheet, there should
have been at least another byte that would have contained the
correct OOB size that Andreas needed.
Miquel and Andreas are both favoring reverting the patch over
further, possibly hacky modifications:
"[Reverting] is the safest option here. Apart from this device, we
do not know how many devices have these damaged/counterfeit chips.
If it is just a couple and only on Fritzboxes, as suggested in the
Github issue the patch could be carried through OpenWrt[...]"
Thanks to several users on the openwrt forum and github issue,
who stayed along for the ride:
- Peter-vdL for reporting the issue and testing patches.
- neg2led and Hannu Nyman who did all the
datasheet digging and debugging.
Cc: Andreas Boehler <dev@aboehler.at>
Suggested-by: Andreas Boehler <dev@aboehler.at>
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/issues/9962
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607185918.1048204-1-chunkeey@gmail.com
The Linux device core doesn't intend remove callbacks to fail. If an
error code is returned the device is removed anyhow. So wail loudly if
the atmel specific remove callback fails and return 0 anyhow to suppress
the generic (and little helpful) error message by the device core.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220607062503.211345-1-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it. Then meson_nfc_nand_chip_cleanup() returns 0 unconditionally and can
be changed to return void which allows further simplification in the
remove callback.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-12-u.kleine-koenig@pengutronix.de
If mtd_device_unregister() fails (which it doesn't when used correctly),
the resources bound by the nand chip should be freed anyhow as returning
an error value doesn't prevent the device getting unbound.
Instead use WARN_ON on the return value similar to how other drivers do
it.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-11-u.kleine-koenig@pengutronix.de
Returning an error value in a platform remove callback results in an error
message being emitted by the platform core, but otherwise it doesn't make
a difference. After the WARN splat this generic error message doesn't add
any value, so return 0 unconditionally
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220603210758.148493-10-u.kleine-koenig@pengutronix.de
When meson_nfc_nand_chip_cleanup() is called, it will call:
meson_nfc_free_buffer(&meson_chip->nand);
nand_cleanup(&meson_chip->nand);
nand_cleanup() in turn will call nand_detach() which calls the
.detach_chip() which is here meson_nand_detach_chip().
meson_nand_detach_chip() already calls meson_nfc_free_buffer(), so we
could double free some memory.
Fix it by removing the unneeded explicit call to meson_nfc_free_buffer().
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/ec15c358b8063f7c50ff4cd628cf0d2e14e43f49.1653064877.git.christophe.jaillet@wanadoo.fr
Driver should call pci_disable_device() if it returns from
cafe_nand_probe() with error.
Meanwhile, the driver calls pci_enable_device() in
cafe_nand_probe(), but never calls pci_disable_device()
during removal.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220520084425.116686-1-wupeng58@huawei.com
* Call of_platform_populate() for MTD partitions
* Check devicetree alias for index
* mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
* mtdblock: Warn if opened on NAND
* Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
* st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
* phram:
- Allow cached mappings
- Allow probing via reserved-memory
* maps: ixp4xx: Drop driver
* bcm47xxpart: Print correct offset on read error
CFI driver changes:
* Rename chip_ready variables
* Add S29GL064N ID definition
* Use chip_ready() for write on S29GL064N
* Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
* Print offset instead of page number for bad blocks
Raw NAND controller drivers:
* Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
* CS553X: simplify the return expression of cs553x_write_ctrl_byte()
* Davinci: Remove redundant unsigned comparison to zero
* Denali: Use managed device resources
* GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
* Intel: Fix possible null-ptr-deref in ebu_nand_probe()
* MPC5121: Check before clk_disable_unprepare() not needed
* Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
* OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
* Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
* Rockchip: Check before clk_disable_unprepare() not needed
* TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
* Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
* Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
* XTX: Add support for XT26G0xA
SPI NOR core changes:
* Read back written SR value to make sure the write was done correctly.
* Introduce a common function for Read ID that manufacturer drivers can
use to verify the Octal DTR switch worked correctly.
* Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
* Clarify rdsr dummy cycles documentation.
* Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
* Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
* Move spi_nor_write_ear() to Winbond module since only Winbond flashes
use it.
* Rework Micron and Cypress Octal DTR enable methods to improve
readability.
* Use the common Read ID function to verify switch to Octal DTR mode for
Micron and Cypress flashes.
* Skip polling status on volatile register writes for Micron and Cypress
flashes since the operation is instant.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmKHhXEACgkQJWrqGEe9
VoQ4FQgAwTWnv7Eps8ngxlOE1WW1Kx+XUFCYN7mUKmDycgRKWWqF0OUu3pU6T3Si
XoOixajzsPC7AJtXbbGKUkH3UtqapCZ/OVxMJzY1S1zKVgS72ChvPth+rNOA5H6f
wkwCRYBCm51hYAlOQeRoFtwLEpOP17KTZw9Jn/u5RVwbQedQnzPj5sb6PddejjF4
9nlk2auJHzENBEEBG3WLRNgvGep8mNNFarzWB4iWrMcG0w1EgBksbIdshoBmu7vj
nKcDJbyA81DqX+8d56BfAFih8H2yCXZmhUzMK+zqnNkd1NuPnDDnrQYFKmKm2hAg
3bIMIzi+8dl/m0TY6BHPHj8oIYpjYA==
=P95J
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Call of_platform_populate() for MTD partitions
- Check devicetree alias for index
- mtdoops:
- Add a timestamp to the mtdoops header.
- Create a header structure for the saved mtdoops.
- Fix the size of the header read buffer.
- mtdblock: Warn if opened on NAND
- Bindings:
- reserved-memory: Support MTD/block device
- jedec,spi-nor: remove unneeded properties
- Extend fixed-partitions binding
- Add Sercomm (Suzhou) Corporation vendor prefix
MTD driver changes:
- st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
- phram:
- Allow cached mappings
- Allow probing via reserved-memory
- maps: ixp4xx: Drop driver
- bcm47xxpart: Print correct offset on read error
CFI driver changes:
- Rename chip_ready variables
- Add S29GL064N ID definition
- Use chip_ready() for write on S29GL064N
- Move and rename chip_check/chip_ready/chip_good_for_write
NAND core changes:
- Print offset instead of page number for bad blocks
Raw NAND controller drivers:
- Cadence: Fix possible null-ptr-deref in cadence_nand_dt_probe()
- CS553X: simplify the return expression of cs553x_write_ctrl_byte()
- Davinci: Remove redundant unsigned comparison to zero
- Denali: Use managed device resources
- GPMI:
- Add large oob bch setting support
- Rename the variable ecc_chunk_size
- Uninline the gpmi_check_ecc function
- Add strict ecc strength check
- Refactor BCH geometry settings function
- Intel: Fix possible null-ptr-deref in ebu_nand_probe()
- MPC5121: Check before clk_disable_unprepare() not needed
- Mtk:
- MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
- Also parse the default nand-ecc-engine property if available
- Make mtk_ecc.c a separated module
- OMAP ELM:
- Convert the bindings to yaml
- Describe the bindings for AM64 ELM
- Add support for its compatible
- Renesas: Use runtime PM instead of the raw clock API and update the
bindings accordingly
- Rockchip: Check before clk_disable_unprepare() not needed
- TMIO: Check return value after calling platform_get_resource()
Raw NAND chip driver:
- Kioxia: Add support for TH58NVG3S0HBAI4 and TC58NVG0S3HTA00
SPI-NAND chip drivers:
- Gigadevice:
- Add support for:
- GD5FxGM7xExxG
- GD5F{2,4}GQ5xExxG
- GD5F1GQ5RExxG
- GD5FxGQ4xExxG
- Fix Quad IO for GD5F1GQ5UExxG
- XTX: Add support for XT26G0xA
SPI NOR core changes:
- Read back written SR value to make sure the write was done
correctly.
- Introduce a common function for Read ID that manufacturer drivers
can use to verify the Octal DTR switch worked correctly.
- Add helpers for read/write any register commands so manufacturer
drivers don't open code it every time.
- Clarify rdsr dummy cycles documentation.
- Add debugfs entry to expose internal flash parameters and state.
SPI NOR manufacturer drivers changes:
- Add support for Winbond W25Q512NW-IM, and Eon EN25QH256A.
- Move spi_nor_write_ear() to Winbond module since only Winbond
flashes use it.
- Rework Micron and Cypress Octal DTR enable methods to improve
readability.
- Use the common Read ID function to verify switch to Octal DTR mode
for Micron and Cypress flashes.
- Skip polling status on volatile register writes for Micron and
Cypress flashes since the operation is instant"
* tag 'mtd/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (68 commits)
mtd: st_spi_fsm: add missing clk_disable_unprepare() in stfsm_remove()
dt-bindings: mtd: partitions: Extend fixed-partitions binding
dt-bindings: Add Sercomm (Suzhou) Corporation vendor prefix
mtd: phram: Allow cached mappings
mtd: call of_platform_populate() for MTD partitions
mtd: rawnand: renesas: Use runtime PM instead of the raw clock API
dt-bindings: mtd: renesas: Fix the NAND controller description
mtd: rawnand: mpc5121: Check before clk_disable_unprepare() not needed
mtd: rawnand: rockchip: Check before clk_disable_unprepare() not needed
mtd: nand: MTD_NAND_ECC_MEDIATEK should depend on ARCH_MEDIATEK
mtd: rawnand: cs553x: simplify the return expression of cs553x_write_ctrl_byte()
mtd: rawnand: kioxia: Add support for TH58NVG3S0HBAI4
mtd: spi-nor: debugfs: fix format specifier
mtd: spi-nor: support eon en25qh256a variant
mtd: spi-nor: winbond: add support for W25Q512NW-IM
mtd: spi-nor: expose internal parameters via debugfs
mtd: spi-nor: export spi_nor_hwcaps_pp2cmd()
mtd: spi-nor: move spi_nor_write_ear() to winbond module
mtd: spi-nor: amend the rdsr dummy cycles documentation
mtd: cfi_cmdset_0002: Rename chip_ready variables
...
This NAND controller is part of a well defined power domain handled by
the runtime PM core. Let's keep the harmony with the other RZ/N1 drivers
and exclusively use the runtime PM API to enable/disable the clocks.
We still need to retrieve the external clock rate in order to derive the
NAND timings, but that is not a big deal, we can still do that in the
probe and just save this value to reuse it later.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/linux-mtd/20220513104957.257721-3-miquel.raynal@bootlin.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512185033.46901-1-phil.edworthy@renesas.com
All code in clk_disable_unprepare() already checks the clk ptr using
IS_ERR_OR_NULL so there is no need to check it again before calling it.
A lot of other drivers already rely on this behaviour, so it's safe
to do so here.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220512184558.45966-1-phil.edworthy@renesas.com
The MediaTek Hardware ECC Engine is only present on MediaTek MT27xx and
MT76xx SoCs. The driver for this engine is a dependency for the
MediaTek NAND controller (MTD_NAND_MTK) and the MediaTek SPI NAND Flash
Interface (SPI_MTK_SNFI) drivers, both of which already depend on
ARCH_MEDIATEK.
Hence add a dependency on ARCH_MEDIATEK to the Hardware ECC Engine
driver, too, to prevent asking the user about this driver when
configuring a kernel without MediaTek SoC support.
Fixes: 4fd62f15af ("mtd: nand: make mtk_ecc.c a separated module")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/bb9568e825d4bc7506870b03836baa91bcc4b725.1652104136.git.geert+renesas@glider.be
Add timings for Kioxia/Toshiba TH58NVG3S0HBAI4. Timings
for this memory matches the timings selected for
TH58NVG2S3HBAI4.
This patch increases eraseblock write speed from 5248 KiB/s
to 6864 KiB/s and erase block read speed from 8542 KiB/s
to 18360 KiB/s
Tested on i.MX6SX.
Signed-off-by: Rickard x Andersson <rickaran@axis.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220429083931.26795-1-rickaran@axis.com
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmJpa+MACgkQJWrqGEe9
VoTVPwf+PjOPS9MH+3wQkEsqwHtJyC9dvfTRWNSkzJEos0710jl6peeWjo1ift1A
4JLMI3TGHWbNqBykpSLxZPVc6X/toGoMz6/2OussnYQBYgXjLNOgWQqS4kZZmK7D
BARpke8TTqglJyat7NpGNo1EGWA4EtYqwvoPT+H0LMLQbe/NQD0k4RaRNpw+BwPq
gaBHZf/CmN4oG0QrPPvS7jrm0dgWrQgTqRf9zzOnml3m22q3PGMnmY1A1CunBsFn
HK+GxYUOeemPc40mET+U1x6O0+VNlxW2KQ+fZoNHnljd55zq1Cp4mXfr7KuFgfDK
4xMAAoI5cMp8kpLLVUBlD4uzOj3fow==
=FBXD
-----END PGP SIGNATURE-----
Merge tag 'mtd/mtk-spi-nand-for-5.19' into nand/next
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The recently added ECC engine support introduced a generic property
named nand-ecc-engine for ecc engine phandle. This patch adds support
for this new property.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-4-gch981213@gmail.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-2-yangyingliang@huawei.com
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: ec4ba01e89 ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220426084913.4021868-1-yangyingliang@huawei.com
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 bytes OOB. This adds a static NAND ID entry to correct this.
Tested on FRITZ!Box 7530 flashed with OpenWrt.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220420104034.6333-1-dev@aboehler.at
The code change proposes a new way to set bch geometry for large oob
NAND (oobsize > 1KB). In this case, previous implementation can NOT
guarantee the bad block mark always locates in data chunk, so we need a
new way to do it. The general idea is,
1.Try all ECC strength from the maximum ecc that controller can support
to minimum value required by NAND chip, any ECC strength makes the
BBM locate in data chunk can be eligible.
2.If none of them works, using separate ECC for meta, which will add
one extra ecc with the same ECC strength as other data chunks. This
extra ECC can guarantee BBM located in data chunk, also we need to
check if oob can afford it.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-6-han.xu@nxp.com
There is only one variable ecc_chunk_size in bch_geometry data
structure but two different field in BCH registers. The data0_size in
BCH_FLASH0LAYOUT0 and datan_size in BCH_FLASH0LAYOUT1 should have
dedicate variable since they might set to different values in some
cases. For instance, if need dedicate ecc for meta area, the data0_size
should be 0 rather than datan_size, but for all other cases, data0_size
still equals to datan_size and it won't bring any function change.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-5-han.xu@nxp.com
Add nand_ecc_is_strong_enough() check in gpmi_check_ecc() function to
make sure ecc strength can meet chip requirement.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-3-han.xu@nxp.com
The code change refactor the bch geometry setting function, which
doesn't change the default behavior, while user may choose to use chips
required minimum ecc strength by DT flag "fsl,use-minimum-ecc".
The default way to set bch geometry need to set the data chunk
size(step_size) larger than oob size to make sure BBM locates in data
chunk, then set the maximum ecc strength oob can hold. It always use
unbalanced ECC layout, which ecc0 will cover both meta and data0 chunk.
But the default bch setting is deprecated for large oobsize NAND
(oobsize >1KB), so in the patch set, there is a split commit that
introduces a new way to set bch geometry for large oob size NAND.
For all other cases,set the bch geometry by chip required strength and
step size, which uses the minimum ecc strength chip required. It can be
explicitly enabled by DT flag "fsl,use-minimum-ecc", but need to be
en/disabled in both u-boot and kernel at the same time.
Signed-off-by: Han Xu <han.xu@nxp.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412025246.24269-2-han.xu@nxp.com
All of the resources used by this driver has managed interfaces, so use
them. Otherwise we will get the following splat:
[ 4.472703] denali-nand-pci 0000:00:05.0: timeout while waiting for irq 0x1000
[ 4.474071] denali-nand-pci: probe of 0000:00:05.0 failed with error -5
[ 4.473538] nand: No NAND device found
[ 4.474068] BUG: unable to handle page fault for address: ffffc90005000410
[ 4.475169] #PF: supervisor write access in kernel mode
[ 4.475579] #PF: error_code(0x0002) - not-present page
[ 4.478362] RIP: 0010:iowrite32+0x9/0x50
[ 4.486068] Call Trace:
[ 4.486269] <IRQ>
[ 4.486443] denali_isr+0x15b/0x300 [denali]
[ 4.486788] ? denali_direct_write+0x50/0x50 [denali]
[ 4.487189] __handle_irq_event_percpu+0x161/0x3b0
[ 4.487571] handle_irq_event+0x7d/0x1b0
[ 4.487884] handle_fasteoi_irq+0x2b0/0x770
[ 4.488219] __common_interrupt+0xc8/0x1b0
[ 4.488549] common_interrupt+0x9a/0xc0
Fixes: 93db446a42 ("mtd: nand: move raw NAND related code to the raw/ subdir")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220411125808.958276-1-zheyuma97@gmail.com
This patch fixes a memory corruption that occurred in the
nand_scan() path for Hynix nand device.
On boot, for Hynix nand device will panic at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual
address 00000070
| [00000070] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.17.0-01473-g13ae1769cfb0
#38
| Hardware name: Generic DT based system
| PC is at nandc_set_reg+0x8/0x1c
| LR is at qcom_nandc_command+0x20c/0x5d0
| pc : [<c088b74c>] lr : [<c088d9c8>] psr: 00000113
| sp : c14adc50 ip : c14ee208 fp : c0cc970c
| r10: 000000a3 r9 : 00000000 r8 : 00000040
| r7 : c16f6a00 r6 : 00000090 r5 : 00000004 r4 :c14ee040
| r3 : 00000000 r2 : 0000000b r1 : 00000000 r0 :c14ee040
| Flags: nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Register r0 information: slab kmalloc-2k start c14ee000 pointer offset
64 size 2048
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| nandc_set_reg from qcom_nandc_command+0x20c/0x5d0
| qcom_nandc_command from nand_readid_op+0x198/0x1e8
| nand_readid_op from hynix_nand_has_valid_jedecid+0x30/0x78
| hynix_nand_has_valid_jedecid from hynix_nand_init+0xb8/0x454
| hynix_nand_init from nand_scan_with_ids+0xa30/0x14a8
| nand_scan_with_ids from qcom_nandc_probe+0x648/0x7b0
| qcom_nandc_probe from platform_probe+0x58/0xac
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4 or 8 based on page size.
This causes the sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_command() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch will update nandc->max_cwperpage 1 to 4 or 8 based on page
size in qcom_nand_attach_chip call back after freeing the previously
allocated memory for bam txn as per nandc->max_cwperpage = 1 and then
again allocating bam txn as per nandc->max_cwperpage = 4 or 8 based on
page size in qcom_nand_attach_chip call back itself.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Reported-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Co-developed-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Sricharan R <quic_srichara@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1650268107-5363-1-git-send-email-quic_mdalam@quicinc.com
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 83738d87e3 ("mtd: sh_flctl: Add DMA capabilty")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220412083435.29254-1-linmq006@gmail.com
According to the datasheet, mt7622 only has 5 ECC capabilities instead
of 7, and the decoding error register is arranged as follows:
+------+---------+---------+---------+---------+
| Bits | 19:15 | 14:10 | 9:5 | 4:0 |
+------+---------+---------+---------+---------+
| Name | ERRNUM3 | ERRNUM2 | ERRNUM1 | ERRNUM0 |
+------+---------+---------+---------+---------+
This means err_mask should be 0x1f instead of 0x3f and the number of
bits shifted in mtk_ecc_get_stats should be 5 instead of 8.
This commit introduces err_shift for the difference in this register
and fix other existing parameters.
Public MT7622 reference manual can be found on [0] and the info this
commit is based on is from page 656 and page 660.
[0]: https://wiki.banana-pi.org/Banana_Pi_BPI-R64#Documents
Fixes: 98dea8d719 ("mtd: nand: mtk: Support MT7622 NAND flash controller.")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220402160315.919094-1-gch981213@gmail.com
This makes printed info consistent with other kernel messages. After
scanning NAND BBT create_bbt() prints offset of each bad block. This
change makes is easy to verify nand_erase_nand() failure reason.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220326163304.30806-1-zajec5@gmail.com
Add support for:
GD5F{1,2}GM7{U,R}ExxG
GD5F4GM8{U,R}ExxG
These are new 27nm counterparts for the GD5FxGQ4 chips from GigaDevice
with 8b/512b on-die ECC capability.
These chips (and currently supported GD5FxGQ5 chips) have QIO DTR
instruction for reading page cache. It isn't added in this patch because
I don't have a DTR spi controller for testing.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-6-gch981213@gmail.com
Add support for:
GD5F2GQ5{U,R}ExxG
GD5F4GQ6{U,R}ExxG
These chips uses 4 dummy bytes for quad io and 2 dummy bytes for dual io.
Besides that and memory layout, they are identical to their 1G variant.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-5-gch981213@gmail.com
Add support for:
GD5F1GQ4RExxG
GD5F2GQ4{U,R}ExxG
These chips differ from GD5F1GQ4UExxG only in chip ID, voltage
and capacity.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220320100001.247905-3-gch981213@gmail.com
* Replace the expert mode symbols with a single helper
* Fix misuses of of_match_ptr()
* Remove partid and partname debugfs files
* tests: Fix eraseblock read speed miscalculation for lower partition sizes
* TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
* spear_smi: use GFP_KERNEL
* mchp48l640: Add SPI ID table
* mchp23k256: Add SPI ID table
* blkdevs: Avoid soft lockups with some mtd/spi devices
* aspeed-smc: Improve probe resilience
Hyperbus changes:
* HBMC_AM654 should depend on ARCH_K3
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
* Fix misuses of of_match_node()
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI NOR core changes:
* Move vendor specific code out of the core into vendor drivers.
* Unify all function and object names in the vendor modules.
* Make setup() callback optional to improve readability.
* Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
* Dropped mtd/cortina,gemini-flash.txt
* Convert BCM47xx partitions to json-schema
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI7WJcACgkQJWrqGEe9
VoSzpAgAutzRv9TRUiXdBGGlJ851QaZ6ZUvT1bHKTQA+xZi+MZyNmc0cWNg3B70I
PnwyxNAmRkUQKwV5Vgy/sQrt42qZnPmr+8XMq+UiziPmgFdjiTdLqGcN619Hi12t
JqtoKL828R064LSEq5nWsJ2waoGT1nNtZK8kA2qe8ctvmH0YTThriVZUQR4/Befb
OGFheceLFycE/vkktPPr3As4603fMiyDOT7EA3Mtzgjohry0a0TqoakHCaHC/fYo
0/h+x+jJATPtgbWm1ZiV3cZ/Su00+rKuQOsiAWvM/pqDaijsVntBmtK0PRtums2Q
m8LCspuQYNnCINeQXqba9RxACpibDg==
=+6Zk
-----END PGP SIGNATURE-----
Merge tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"There has been a lot of activity in the MTD subsystem recently, with a
number of SPI-NOR cleanups as well as the introduction of ECC engines
that can be used by SPI controllers (hence a few SPI patches in here).
Core MTD changes:
- Replace the expert mode symbols with a single helper
- Fix misuses of of_match_ptr()
- Remove partid and partname debugfs files
- tests: Fix eraseblock read speed miscalculation for lower partition
sizes
- TRX parser: Allow to use on MediaTek MIPS SoCs
MTD driver changes:
- spear_smi: use GFP_KERNEL
- mchp48l640: Add SPI ID table
- mchp23k256: Add SPI ID table
- blkdevs: Avoid soft lockups with some mtd/spi devices
- aspeed-smc: Improve probe resilience
Hyperbus changes:
- HBMC_AM654 should depend on ARCH_K3
NAND core changes:
- ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
- Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
- Make two read-only arrays static const
- Fix compile test issue
Raw NAND core changes:
- Fix misuses of of_match_node()
- Rework of_get_nand_bus_width()
- Remove of_get_nand_on_flash_bbt() wrapper
- Protect access to rawnand devices while in suspend
- bindings: Document the wp-gpios property
Rax NAND controller driver changes:
- atmel: Fix refcount issue in atmel_nand_controller_init
- nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
- rockchip: Fix platform_get_irq.cocci warning
- stm32_fmc2: Add NAND Write Protect support
- pl353: Set the nand chip node as the flash node
- brcmnand: Fix sparse warnings in bcma_nand
- omap_elm: Remove redundant variable 'errors'
- gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
- brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
- Check for error irq
SPI-NAND core changes:
- Delay a little bit the dirmap creation
- Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
- macronix: Use random program load
SPI NOR core changes:
- Move vendor specific code out of the core into vendor drivers.
- Unify all function and object names in the vendor modules.
- Make setup() callback optional to improve readability.
- Skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
SPI changes:
- Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
- spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
Binding changes:
- Dropped mtd/cortina,gemini-flash.txt
- Convert BCM47xx partitions to json-schema
- Vendor prefixes: Clarify Macronix prefix
- SPI NAND: Convert spi-nand description file to yaml
- Raw NAND chip: Create a NAND chip description
- Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
- Describe Macronix NAND ECC engine
- Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory"
* tag 'mtd/changes-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (104 commits)
mtd: nand: ecc: mxic: Fix compile test issue
mtd: nand: mxic-ecc: make two read-only arrays static const
mtd: hyperbus: HBMC_AM654 should depend on ARCH_K3
mtd: core: Remove partid and partname debugfs files
dt-bindings: mtd: partitions: convert BCM47xx to the json-schema
mtd: tests: Fix eraseblock read speed miscalculation for lower partition sizes
mtd: rawnand: atmel: fix refcount issue in atmel_nand_controller_init
mtd: rawnand: rockchip: fix platform_get_irq.cocci warning
mtd: spi-nor: Skip erase logic when SPI_NOR_NO_ERASE is set
mtd: spi-nor: renumber flags
mtd: spi-nor: slightly change code style in spi_nor_sr_ready()
mtd: spi-nor: spansion: rename vendor specific functions and defines
mtd: spi-nor: spansion: convert USE_CLSR to a manufacturer flag
mtd: spi-nor: move all spansion specifics into spansion.c
mtd: spi-nor: spansion: slightly rework control flow in late_init()
mtd: spi-nor: micron-st: rename vendor specific functions and defines
mtd: spi-nor: micron-st: convert USE_FSR to a manufacturer flag
mtd: spi-nor: move all micron-st specifics into micron-st.c
mtd: spi-nor: xilinx: correct the debug message
mtd: spi-nor: xilinx: rename vendor specific functions and defines
...
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmI021sACgkQJWrqGEe9
VoTEcggAiFXD+oR0VXTsykiNDiopsAUZwLPGuqk8gvD4ozOYCoAEoYrtnBM6Uybz
W6Hu6Eow/ri1H+uVygUw3RYa4TpxrZrmZnJ1YimXxZjbLYjgE3FS9vzh2l4Bu3yo
fkkQH+nFvk9qVIK8qolAny+LWl37gkSnCd6mPPksYaG5Ds1n1ZgyTZVUz5TOWAjG
QAWUQQfO1iu7+u4CXa9JRTkCf55bT6v6c9Ryq6MA+ok6jVRN6Cj9WhxHtCB5vmOH
Ndmu4V8BqaNKg39ltolqSPuwt3GEh707LRr+YakfnaOM7Sf8E/evn/THSkHwY/yn
bAjpU1gvS13nJ++s8nHwIhHKhoYjTg==
=4Uke
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.18' into mtd/next
Raw NAND core changes:
* Rework of_get_nand_bus_width()
* Remove of_get_nand_on_flash_bbt() wrapper
* Protect access to rawnand devices while in suspend
* bindings: Document the wp-gpios property
Rax NAND controller driver changes:
* atmel: Fix refcount issue in atmel_nand_controller_init
* nandsim:
- Add NS_PAGE_BYTE_SHIFT macro to replace the repeat pattern
- Merge repeat codes in ns_switch_state
- Replace overflow check with kzalloc to single kcalloc
* rockchip: Fix platform_get_irq.cocci warning
* stm32_fmc2: Add NAND Write Protect support
* pl353: Set the nand chip node as the flash node
* brcmnand: Fix sparse warnings in bcma_nand
* omap_elm: Remove redundant variable 'errors'
* gpmi:
- Support fast edo timings for mx28
- Validate controller clock rate
- Fix controller timings setting
* brcmnand:
- Add BCMA shim
- BCMA controller uses command shift of 0
- Allow platform data instantation
- Add platform data structure for BCMA
- Allow working without interrupts
- Move OF operations out of brcmnand_init_cs()
- Avoid pdev in brcmnand_init_cs()
- Allow SoC to provide I/O operations
- Assign soc as early as possible
Onenand changes:
* Check for error irq
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmInffUACgkQS1VPR6WN
FOn9fwf/SCIvgoScBNeQjW4cGTmh11oO+O8i2umibq0pQDLrNF6Ul7ykY6Fdm4Dc
+Ce7c4Vp0O+DRphIkaK5MtNgRmXMOQbqUKcNAQftFS0wCtJ+QVQzOvkVGS3jQA74
KVEY3Jiup3Q5qknBg0r890ENwRLmcGJaPi5DAO+uHcf6ItTpwjv3z6C2ZUeiH6UK
PMSwZgd86dwwH2eU4G5EoAjA+nqOcVvH0V1F49DFsGZ3kkmUS6nMNnSpb5SykszT
4uq+7+c3E2UOC0TlUkyX/xTv4DoZZDi6qqVEaV14bELL1a0FdltjKyIuWTds1Tei
rwPhEOkqOpSnBVjlUWb7icwef21NWg==
=QFe+
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.18' into mtd/next
SPI NOR core changes:
- move vendor specific code out of the core into vendor drivers.
- unify all function and object names in the vendor modules.
- make setup() callback optional to improve readability.
- skip erase logic when the SPI_NOR_NO_ERASE flag is set at flash
declaration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid random build errors with architectures which do not select
HAS_IOMEM by depending on it in Kconfig.
This fixes the following warning:
/home/mraynal/0day/gcc-11.2.0-nolibc/s390-linux/bin/s390-linux-ld:
drivers/mtd/nand/ecc-mxic.o: in function `mxic_ecc_probe':
ecc-mxic.c:(.text+0x2244): undefined reference to `devm_platform_ioremap_resource'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220314152336.75447-1-miquel.raynal@bootlin.com
Don't populate the read-only arrays possible_strength and
spare_size on the stack but instead make them static
const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220307230940.169235-1-colin.i.king@gmail.com
The reference counting issue happens in several error handling paths
on a refcounted object "nc->dmac". In these paths, the function simply
returns the error code, forgetting to balance the reference count of
"nc->dmac", increased earlier by dma_request_channel(), which may
cause refcount leaks.
Fix it by decrementing the refcount of specific object in those error
paths.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Co-developed-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Co-developed-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220304085330.3610-1-xiongx18@fudan.edu.cn
The root of the problem is that we are selecting symbols that have
dependencies. This can cause random configurations that can fail.
The cleanest solution is to avoid using select.
This driver uses interfaces from the OMAP_GPMC driver so we have to
depend on it instead.
Fixes: 4cd335dae3 ("mtd: rawnand: omap2: Prevent invalid configuration and build error")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/linux-mtd/20220219193600.24892-1-rogerq@kernel.org
This patch adds the support of the WP# signal. WP will be disabled in
probe/resume callbacks and will be enabled in remove/suspend callbacks.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220217144755.270679-3-christophe.kerello@foss.st.com
In devicetree the flash information is embedded within nand chip node,
so during nand chip initialization the nand chip node should be passed
to nand_set_flash_node() api, instead of nand controller node.
Fixes: 08d8c62164 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220209053427.27676-1-amit.kumar-mahapatra@xilinx.com
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmIPpwcACgkQJWrqGEe9
VoRbnwgAgW9tSKGp1B6eA3Xf7Or0SZfmC6H0scV8kfQ2i9OnMOuYMAGs+7whNrcx
Dvb9IfFOMra7umid98EI58YhLsu4IMDtc79Lp04HGY/emjZh47FpAEXZ/vr/45e9
lclUEmjHwUVJ5+XvFwnPLpIWiM0xeL3CN2rAi76uI5sII+Hxt6KkV7L9+N9IjhcA
GsG/8/A16ihbNjVrHoN+ofwmmZkySXvhK7IIg93Tv+VoJCBnn0eEDgtRXvsGoDuq
2xD87MEAhnXw+q9LtSSUwmA/uUCR2RscidGQ+LML0PwKDVUZhzBV8sNrNoPQy374
51XXDCkSF8NRK+FVXIUFTEctdVrE1A==
=UuhB
-----END PGP SIGNATURE-----
Merge tag 'mtd/spi-mem-ecc-for-5.18' into mtd/next
Topic branch bringing-in changes related to the support of ECC engines
that can be used by SPI controllers to manage SPI NANDs as well as
possibly by parallel NAND controllers. In particular, it brings support
for Macronix ECC engine that can be used with Macronix SPI controller.
The changes touch the NAND core, the NAND ECC core, the spi-mem layer, a
SPI controller driver and add a new NAND ECC driver, as well as a number
of binding updates.
Binding changes:
* Vendor prefixes: Clarify Macronix prefix
* SPI NAND: Convert spi-nand description file to yaml
* Raw NAND chip: Create a NAND chip description
* Raw NAND controller:
- Harmonize the property types
- Fix a comment in the examples
- Fix the reg property description
* Describe Macronix NAND ECC engine
* Macronix SPI controller:
- Document the nand-ecc-engine property
- Convert to yaml
- The interrupt property is not mandatory
NAND core changes:
* ECC:
- Add infrastructure to support hardware engines
- Add a new helper to retrieve the ECC context
- Provide a helper to retrieve a pilelined engine device
NAND-ECC changes:
* Macronix ECC engine:
- Add Macronix external ECC engine support
- Support SPI pipelined mode
SPI-NAND core changes:
* Delay a little bit the dirmap creation
* Create direct mapping descriptors for ECC operations
SPI-NAND driver changes:
* macronix: Use random program load
SPI changes:
* Macronix SPI controller:
- Fix the transmit path
- Create a helper to configure the controller before an operation
- Create a helper to ease the start of an operation
- Add support for direct mapping
- Add support for pipelined ECC operations
* spi-mem:
- Introduce a capability structure
- Check the controller extra capabilities
- cadence-quadspi/mxic: Provide capability structures
- Kill the spi_mem_dtr_supports_op() helper
- Add an ecc parameter to the spi_mem_op structure
In order for pipelined ECC engines to be able to enable/disable the ECC
engine only when needed and avoid races when future parallel-operations
will be supported, we need to provide the information about the use of
the ECC engine in the direct mapping hooks. As direct mapping
configurations are meant to be static, it is best to create two new
mappings: one for regular 'raw' accesses and one for accesses involving
correction. It is up to the driver to use or not the new ECC enable
boolean contained in the spi-mem operation.
As dirmaps are not free (they consume a few pages of MMIO address space)
and because these extra entries are only meant to be used by pipelined
engines, let's limit their use to this specific type of engine and save
a bit of memory with all the other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-9-miquel.raynal@bootlin.com
As we will soon tweak the dirmap creation to act a little bit
differently depending on the picked ECC engine, we need to initialize
dirmaps after ECC engines. This should not have any effect as dirmaps
are not yet used at this point.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20220127091808.1043392-8-miquel.raynal@bootlin.com
Introduce the support for another possible configuration: the ECC
engine may work as DMA master (pipelined) and move itself the data
to/from the NAND chip into the buffer, applying the necessary
corrections/computations on the fly.
This driver offers an ECC engine implementation that must be
instatiated from a SPI controller driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-17-miquel.raynal@bootlin.com
In a pipelined engine situation, we might either have the host which
internally has support for error correction, or have it using an
external hardware block for this purpose. In the former case, the host
is also the ECC engine. In the latter case, it is not. In order to get
the right pointers on the right devices (for example: in order to devm_*
allocate variables), let's introduce this helper which can safely be
called by pipelined ECC engines in order to retrieve the right device
structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-16-miquel.raynal@bootlin.com
Some SPI-NAND chips do not support on-die ECC. For these chips,
correction must apply on the SPI controller end. In order to avoid
doing all the calculations by software, Macronix provides a specific
engine that can offload the intensive work.
Add Macronix ECC engine support, this engine can work in conjunction
with a SPI controller and a raw NAND controller, it can be pipelined
or external and supports linear and syndrome layouts.
Right now the simplest configuration is supported: SPI controller
external and linear ECC engine.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-15-miquel.raynal@bootlin.com
Prevent rawnand access while in a suspended state.
Commit 013e6292aa ("mtd: rawnand: Simplify the locking") allows the
rawnand layer to return errors rather than waiting in a blocking wait.
Tested on a iMX6ULL.
Fixes: 013e6292aa ("mtd: rawnand: Simplify the locking")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220208085213.1838273-1-sean@geanix.com
Reduce the number of exported symbols by replacing:
- mtd_expert_analysis_warning (the error string)
- mtd_expert_analysis_mode (the boolean)
with a single helper:
- mtd_check_expert_analysis_mode
Calling this helper will both check/return the content of the internal
boolean -which is not exported anymore- and as well conditionally
WARN_ONCE() the user, like it was done before.
While on this function, make the error string local to the helper and
set it const. Only export this helper when CONFIG_DEBUG_FS is defined to
limit the growth of the Linux kernel size only for a debug feature on
production kernels.
Mechanically update all the consumers.
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220128113414.1121924-1-miquel.raynal@bootlin.com
There is no good reason to keep genhd.h separate from the main blkdev.h
header that includes it. So fold the contents of genhd.h into blkdev.h
and remove genhd.h entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20220124093913.742411-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On non-OF enabled platforms (CONFIG_OF is not set), of_match_node() will
expand to NULL. The of_device_id array pointed by the macro will then be
left unused. Let's mark the array __maybe_unused in this case to prevent
compiler warnings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20220127110802.1064963-1-miquel.raynal@bootlin.com
of_match_ptr() either expands to NULL if !CONFIG_OF, or is transparent
otherwise. There are several drivers using this macro which keep their
of_device_id array enclosed within an #ifdef CONFIG_OF check, these are
considered fine. However, When misused, the of_device_id array pointed
by this macro will produce a warning because it is finally unused when
compiled without OF support.
A number of fixes are possible:
- Always depend on CONFIG_OF, but this will not always work and may
break boards.
- Enclose the compatible array by #ifdef's, this may save a bit of
memory but will reduce build coverage.
- Tell the compiler the array may be unused, if this can be avoided,
let's not do this.
- Just drop the macro, setting the of_device_id array for a non OF
enabled platform is not an issue, it will just be unused.
The latter solution seems the more appropriate, so let's use it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/linux-mtd/20220127110631.1064705-1-miquel.raynal@bootlin.com
The brcmnand driver contains a bug in which if a page (example 2k byte)
is read from the parallel/ONFI NAND and within that page a subpage (512
byte) has correctable errors which is followed by a subpage with
uncorrectable errors, the page read will return the wrong status of
correctable (as opposed to the actual status of uncorrectable.)
The bug is in function brcmnand_read_by_pio where there is a check for
uncorrectable bits which will be preempted if a previous status for
correctable bits is detected.
The fix is to stop checking for bad bits only if we already have a bad
bits status.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: david regan <dregan@mail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/trinity-478e0c09-9134-40e8-8f8c-31c371225eda-1643237024774@3c-app-mailcom-lxa02
We need to select MEMORY as well otherwise OMAP_GPMC will not be built.
For simplicity let's select MEMORY and OMAP_GPMC unconditionally as
this driver depends on OMAP_GPMC driver and uses symbols from there.
Fixes: dbcb124ace ("mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118123525.8020-1-rogerq@kernel.org
Interacting with a NAND chip on an IPQ6018 I found that the qcomsmem NAND
partition parser was returning -EPROBE_DEFER waiting for the main smem
driver to load.
This caused the board to reset. Playing about with the probe() function
shows that the problem lies in the core clock being switched off before the
nandc_unalloc() routine has completed.
If we look at how qcom_nandc_remove() tears down allocated resources we see
the expected order is
qcom_nandc_unalloc(nandc);
clk_disable_unprepare(nandc->aon_clk);
clk_disable_unprepare(nandc->core_clk);
dma_unmap_resource(&pdev->dev, nandc->base_dma, resource_size(res),
DMA_BIDIRECTIONAL, 0);
Tweaking probe() to both bring up and tear-down in that order removes the
reset if we end up deferring elsewhere.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220103030316.58301-2-bryan.odonoghue@linaro.org
If of_find_device_by_node() succeeds, ingenic_ecc_get() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling.
Fixes: 15de8c6efd ("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211230072751.21622-1-linmq006@gmail.com
The variable 'errors' is being used to sum the number of errors
but it is never used afterwards. This can be considered a
redundant set of operations and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221181340.524639-1-colin.i.king@gmail.com
In the i.MX28 manual (MCIMX28RM, Rev. 1, 2010) you can find an example
(15.2.4 High-Speed NAND Timing) of how to configure the GPMI controller
to manage High-Speed NAND devices, so it was wrong to assume that only
i.MX6 can achieve EDO timings.
This patch has been tested on a 2048/64 byte NAND (Micron MT29F2G08ABAEAH4).
Kernel mtd tests:
- mtd_nandbiterrs
- mtd_nandecctest
- mtd_oobtest
- mtd_pagetest
- mtd_readtest
- mtd_speedtest
- mtd_stresstest
- mtd_subpagetest
- mtd_torturetest [cycles_count = 10000000]
run without errors.
Before this patch (mode 0):
---------------------------
eraseblock write speed is 2098 KiB/s
eraseblock read speed is 2680 KiB/s
page write speed is 1689 KiB/s
page read speed is 2522 KiB/s
2 page write speed is 1899 KiB/s
2 page read speed is 2579 KiB/s
erase speed is 128000 KiB/s
2x multi-block erase speed is 73142 KiB/s
4x multi-block erase speed is 204800 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
After this patch (mode 5):
-------------------------
eraseblock write speed is 3390 KiB/s
eraseblock read speed is 5688 KiB/s
page write speed is 2680 KiB/s
page read speed is 4876 KiB/s
2 page write speed is 2909 KiB/s
2 page read speed is 5224 KiB/s
erase speed is 170666 KiB/s
2x multi-block erase speed is 204800 KiB/s
4x multi-block erase speed is 256000 KiB/s
8x multi-block erase speed is 256000 KiB/s
16x multi-block erase speed is 256000 KiB/s
32x multi-block erase speed is 256000 KiB/s
64x multi-block erase speed is 256000 KiB/s
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-5-dario.binacchi@amarulasolutions.com
What to do when the real rate of the gpmi clock is not equal to the
required one? The solutions proposed in [1] did not lead to a conclusion
on how to validate the clock rate, so, inspired by the document [2], I
consider the rate correct only if not lower or equal to the rate of the
previous edo mode. In fact, in chapter 4.16.2 (NV-DDR) of the document [2],
it is written that "If the host selects timing mode n, then its clock
period shall be faster than the clock period of timing mode n-1 and
slower than or equal to the clock period of timing mode n.". I thought
that it could therefore also be used in this case, without therefore
having to define the valid rate ranges empirically.
For example, suppose that gpmi_nfc_compute_timings() is called to set
edo mode 5 (100MHz) but the rate returned by clk_round_rate() is 80MHz
(edo mode 4). In this case gpmi_nfc_compute_timings() will return error,
and will be called again to set edo mode 4, which this time will be
successful.
[1] https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org
[2] http://www.onfi.org/-/media/client/onfi/specs/onfi_3_0_gold.pdf?la=en
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-4-dario.binacchi@amarulasolutions.com
Set the controller registers according to the real clock rate. The
controller registers configuration (setup, hold, timeout, ... cycles)
depends on the clock rate of the GPMI. Using the real rate instead of
the ideal one, avoids that this inaccuracy (required_rate - real_rate)
affects the registers setting.
This patch has been tested on two custom boards with i.MX28 and i.MX6
SOCs:
- i.MX28:
required rate 100MHz, real rate 99.3MHz
- i.MX6
required rate 100MHz, real rate 99MHz
Fixes: b120612206 ("mtd: rawnand: gpmi: use core timings instead of an empirical derivation")
Co-developed-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220118095434.35081-3-dario.binacchi@amarulasolutions.com
Add a BCMA shim to allow us to register the brcmnand driver using the
BCMA bus which provides indirect memory mapped access to SoC registers.
There are a number of registers that need to be byte swapped because
they are natively big endian, coming directly from the NAND chip, and
there is no bus interface unlike the iProc or STB platforms that
performs the byte swapping for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-10-f.fainelli@gmail.com
For some odd and unexplained reason the BCMA NAND controller, albeit
revision 3.4 uses a command shift of 0 instead of 24 as it should be,
quirk that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-9-f.fainelli@gmail.com
Make use of the recently refactored code in brcmnand_init_cs() and
derive the chip-select from the platform data that is supplied. Update
the various code paths to avoid relying on possibly non-existent
resources, too.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-8-f.fainelli@gmail.com
The BCMA devices include the brcmnand controller but they do not wire up
any interrupt line, allow the main interrupt to be optional and update
the completion path to also check for the lack of an interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-6-f.fainelli@gmail.com
In order to initialize a given chip select object for use by the
brcmnand driver, move all of the Device Tree specific routines outside
of brcmnand_init_cs() in order to make it usable in a platform data
configuration which will be necessary for supporting BCMA chips.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-5-f.fainelli@gmail.com
In preparation for encapsulating more of what the loop calling
brcmnand_init_cs() does, avoid using platform_device when it is the
device behind platform_device that we are using for printing errors.
No functional changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-4-f.fainelli@gmail.com
Allow a brcmnand_soc instance to provide a custom set of I/O operations
which we will require when using this driver on a BCMA bus which is not
directly memory mapped I/O. Update the nand_{read,write}_reg accordingly
to use the SoC operations if provided.
To minimize the penalty on other SoCs which do support standard MMIO
accesses, we use a static key which is disabled by default and gets
enabled if a soc implementation does provide I/O operations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-3-f.fainelli@gmail.com
In order to key off the brcmnand_probe() code in subsequent changes
depending upon ctrl->soc, assign that variable as early as possible,
instead of much later when we have checked that it is non-NULL.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220107184614.2670254-2-f.fainelli@gmail.com
of_get_nand_bus_width() had a wrong behavior because:
1/ it ignored the -ENODATA and -EOVERFLOW return values of
of_property_read_u32(). "nand-bus-width" without value was tolerated
while it shouldn't have been according to the devicetree bindings.
2/ returned -EIO when the nand-bus-width was neither 8 nor 16, when it
should have returned -EINVAL instead.
3/ returned the 8 or 16 bus-width integer, but it was never used it its
caller. A simply return 0 on success is enough.
Rework of_get_nand_bus_width() and address all the above. The execution
is now stopped in case of errors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220106131610.225661-2-tudor.ambarus@microchip.com
Remove the wrapper as it hides for no reason what we really want: find an
of_property. Removing the wrapper makes the code easier to read.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220106131610.225661-1-tudor.ambarus@microchip.com
For the possible failure of the platform_get_irq(), the returned irq
could be error number and will finally cause the failure of the
request_irq().
Consider that platform_get_irq() can now in certain cases return
-EPROBE_DEFER, and the consequences of letting request_irq() effectively
convert that into -EINVAL, even at probe time rather than later on.
So it might be better to check just now.
Fixes: 2c22120fbd ("MTD: OneNAND: interrupt based wait support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220104162658.1988142-1-jiasheng@iscas.ac.cn
The (ns->regs.column + ns->regs.off) pattern repeats a lot which
represents the byte shift in next page to access. We can replace it
with a macro to improve the readability.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100713.119089-1-s921975628@gmail.com
The moving block of codes is shared between both 'if' and 'else' condition,
we can move it out to reduce the duplication.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100648.119011-1-s921975628@gmail.com
Instead of self-checking overflow and allocating an array of specific size
by counting the total required space handy, we already have existed kernel
API which responses for all these works.
Signed-off-by: RinHizakura <s921975628@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211225100607.118932-1-s921975628@gmail.com
Add the necessary helpers to register/unregister hardware ECC engines
that will be called from ECC engine drivers.
Also add helpers to get the right engine from the user
perspective. Keep a reference of the in use ECC engine in order to
prevent modules to be unloaded. Put the reference when the engine gets
retired.
A static list of hardware (only) ECC engines is setup to keep track of
the registered engines.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-13-miquel.raynal@bootlin.com
Macronix SPI-NAND chips might benefit from an external ECC
engine. Such an engine might need to access random columns, thus needing
to use random commands (0x84 instead of 0x02).
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211216111654.238086-12-miquel.raynal@bootlin.com
- added MIPS support for brcmstb PCIe controller
- added Loongson 2K1000 reset driver
- removed board support for rbtx4938/rbtx4939
- removed support for TX4939 SoCs
- fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=wsIG
-----END PGP SIGNATURE-----
Merge tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- add support for more BCM47XX based devices
- add MIPS support for brcmstb PCIe controller
- add Loongson 2K1000 reset driver
- remove board support for rbtx4938/rbtx4939
- remove support for TX4939 SoCs
- fixes and cleanups
* tag 'mips_5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (59 commits)
MIPS: ath79: drop _machine_restart again
PCI: brcmstb: Augment driver for MIPs SOCs
MIPS: bmips: Remove obsolete DMA mapping support
MIPS: bmips: Add support PCIe controller device nodes
dt-bindings: PCI: Add compatible string for Brcmstb 74[23]5 MIPs SOCs
MIPS: compressed: Fix build with ZSTD compression
MIPS: BCM47XX: Add support for Netgear WN2500RP v1 & v2
MIPS: BCM47XX: Add support for Netgear R6300 v1
MIPS: BCM47XX: Add LEDs and buttons for Asus RTN-10U
MIPS: BCM47XX: Add board entry for Linksys WRT320N v1
MIPS: BCM47XX: Define Linksys WRT310N V2 buttons
MIPS: Remove duplicated include in local.h
MIPS: retire "asm/llsc.h"
MIPS: rework local_t operation on MIPS64
MIPS: fix local_{add,sub}_return on MIPS64
mips/pci: remove redundant ret variable
MIPS: Loongson64: Add missing of_node_put() in ls2k_reset_init()
MIPS: new Kconfig option ZBOOT_LOAD_ADDRESS
MIPS: enable both vmlinux.gz.itb and vmlinuz for generic
MIPS: signal: Return immediately if call fails
...
It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
* ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
* ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
* HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
* Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1.
-----BEGIN PGP SIGNATURE-----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=csTR
-----END PGP SIGNATURE-----
Merge tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's a relatively calm development cycle, but still lots of updates in
the driver side like Intel SOF. Below are some highlights:
ALSA / ASoC core:
- A new kselftest for ALSA control API
- PCM NO_REWINDS support
- Potential race fixes around control removals
- Unify x86 SG-buffer memory allocation code
- Cleanups and race fixes for ASoC DPCM locking
ASoC:
- Refinements and cleanups around the delay() APIs
- Wider use of dev_err_probe().
- Continuing cleanups and improvements to the SOF code
- Support for pin switches in simple-card derived cards
- Support for AMD Renoir ACP, Asahi Kasei Microdevices AKM4375, Intel
systems using NAU8825 and MAX98390, Mediatek MT8915, nVidia Tegra20
S/PDIF, Qualcomm systems using ALC5682I-VS and Texas Instruments
TLV320ADC3xxx
HD-audio / USB-audio:
- Fix deadlock at HD-audio codec unbinding
- Fixes for Tegra194 HD-audio, new HDA support for CS35L41 codec
- Quirks for Lenovo and HP machines, Gigabyte mobo, Bose device
Misc:
- Fix virmidi drain behavior
Note that the merge of CS35L41 codec support is still half-baked, and
at least one ACPI change is missing. Although this won't hinder the
kernel build itself, we're going to catch up before RC1"
* tag 'sound-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (415 commits)
ALSA: hda: intel-dsp-config: reorder the config table
ALSA: hda: intel-dsp-config: add JasperLake support
ALSA: hda: cs35l41: fix double free on error in probe()
ALSA: hda: Fix dependencies of CS35L41 on SPI/I2C buses
ALSA: hda: Fix dependency on ASoC cs35l41 codec
ASoC: cs35l41: Add support for hibernate memory retention mode
ASoC: cs35l41: Update handling of test key registers
ALSA: intel_hdmi: Check for error num after setting mask
ASoC: wcd9335: Keep a RX port value for each SLIM RX mux
ASoC: amd: acp: acp-mach: Change default RT1019 amp dev id
ALSA: virmidi: Remove duplicated code
ALSA: seq: virmidi: Add a drain operation
ASoC: topology: Fix typo
ASoC: fsl_asrc: refine the check of available clock divider
ASoC: Intel: bytcr_rt5640: Add support for external GPIO jack-detect
ASoC: Intel: bytcr_rt5640: Support retrieving the codec IRQ from the AMCR0F28 ACPI dev
ASoC: rt5640: Add support for boards with an external jack-detect GPIO
ASoC: rt5640: Allow snd_soc_component_set_jack() to override the codec IRQ
ASoC: rt5640: Change jack_work to a delayed_work
ASoC: rt5640: Fix possible NULL pointer deref on resume
...
* mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
* gen_probe: Use bitmap_zalloc() when applicable
* Introduce an expert mode for forensics and debugging purposes
* Clear out unregistered devices a bit more
* Provide unique name for nvmem device
* Remove unused header file <linux/mtd/latch-addr-flash.h>
* Fixed breaking list in __mtd_del_partition.
MTD device changes:
* sst25l, mchp48l640, mchp23k256, dataflash:
- Warn about failure to unregister mtd device
Raw NAND core changes:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
* Add Pratyush as SPI NOR co-maintainer.
* Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
* Rework the flash_info flags and clarify where one should be used.
* Initialize all flash parameters based on JESD216 SFDP where possible.
Flash parameters and settings that are SFDP discoverable should not be
duplicated via flash_info flags at flash declaration.
* Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
* Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP standard,
or the SFDP tables which define those flash parameters are not defined
by the flash.
* Fix mtd size for s3an flashes.
* Write 2 bytes when disabling Octal DTR mode: 1 byte long transactions are
not allowed in 8D-8D-8D mode.
Hyperbus changes:
* Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO+g8ACgkQJWrqGEe9
VoRW1AgAjFC58ARNBw7asYerGyiUWv7b8RjPIRWZqmcSQ6D5m20cGNBTa15c2NrC
v0dNMf2+3FrCECso6wKPbkEbLt9lHjlMmt+AdlraV0QvHBXrJq/Tc2p2ATI5kTqq
WaP4oCx1mccgO+IrEIiGikOcFx/TLBBJEk+U0Anbm16eia9Cjw+uD/q7X2HbF5xQ
MOFZyQ+rAVqkM8tCh6VHhCpX85pn9pj2ZdouOhPWsqjULaGqDbUopC70YPZLVJyx
9u4xHFaVLVae6AS5Gitser2ie8klypTN/H+1weSao43GGmwIrT0wK0mCOVIm90Zd
4frlpnt4QE/IIAKgAm+HxkWg+KV9qg==
=E8lV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- mtdchar: Prevent unbounded allocation in MEMWRITE ioctl
- gen_probe: Use bitmap_zalloc() when applicable
- Introduce an expert mode for forensics and debugging purposes
- Clear out unregistered devices a bit more
- Provide unique name for nvmem device
- Remove unused header file <linux/mtd/latch-addr-flash.h>
- Fixed breaking list in __mtd_del_partition.
MTD device changes:
- Warn about failure to unregister mtd device in sst25l, mchp48l640,
mchp23k256, and dataflash drivers.
Raw NAND core changes:
- Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller changes:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller changes:
- OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
- Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
- Onenand:
- Remove redundant variable ooblen
- MPC5121:
- Remove unused variable in ads5121_select_chip()
- GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
- Ingenic:
- JZ4740 needs 'oob_first' read page function
- Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
SPI NOR core changes:
- Add Pratyush as SPI NOR co-maintainer.
- Flash parameters initialization was done in a spaghetti way. Clean
flash parameters initialization.
- Rework the flash_info flags and clarify where one should be used.
- Initialize all flash parameters based on JESD216 SFDP where
possible. Flash parameters and settings that are SFDP discoverable
should not be duplicated via flash_info flags at flash declaration.
- Remove debugfs entries that duplicate sysfs entries.
SPI NOR manufacturer driver changes:
- Use late_init() hook in various drivers to make it clear that those
flash parameters are either not declared in the JESD216 SFDP
standard, or the SFDP tables which define those flash parameters
are not defined by the flash.
- Fix mtd size for s3an flashes.
- Write 2 bytes when disabling Octal DTR mode: 1 byte long
transactions are not allowed in 8D-8D-8D mode.
Hyperbus changes:
- Couple of fixes in Renesas hyperbus rpc-if driver to avoid crash on
module remove and for missing check for error value in probe"
* tag 'mtd/for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (71 commits)
mtd: spi-nor: Remove debugfs entries that duplicate sysfs entries
mtd: spi-nor: micron-st: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: spansion: write 2 bytes when disabling Octal DTR mode
mtd: spi-nor: core: use 2 data bytes for template ops
mtd: spi-nor: Constify part specific fixup hooks
mtd: spi-nor: core: Remove reference to spi-nor.c
mtd: rawnand: gpmi: Use platform_get_irq_byname() to get the interrupt
mtd: rawnand: omap_elm: Use platform_get_irq() to get the interrupt
mtd: rawnand: omap2: Select GPMC device driver for ARCH_K3
memory: omap-gpmc: Use a compatible match table when checking for NAND controller
memory: omap-gpmc: Add support for GPMC on AM64 SoC
dt-bindings: memory-controllers: ti,gpmc: Add compatible for AM64
memory: omap-gpmc: Use platform_get_irq() to get the interrupt
MAINTAINERS: Add an entry for Renesas NAND controller
mtd: rawnand: renesas: Add new NAND controller driver
dt-bindings: mtd: renesas: Describe Renesas R-Car Gen3 & RZ/N1 NAND controller
mtd: rawnand: gpmi: remove unneeded variable
mtd: rawnand: omap2: drop unused variable
mtd: rawnand: omap2: fix force_8bit flag behaviour for DMA mode
mtd: rawnand: omap2: Add compatible for AM64 SoC
...
There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU,
as well as a new USIv2 driver that handles various types of
serial communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple
drivers, as well as memory controller support for RZ/G2L
(R9A07G044).
- Apple M1 gains support for the PMGR power management driver
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmHDpK8ACgkQmmx57+YA
GNmUqhAAnaxXJeu+dfWanrAAeH1MKju/uxB6bogtwrAc928BaqmeZfiAqsT9KsWu
FhkWSGRu+y74fct4zkD3xfl0V2ROSrSjcvrWVu0GJPnXoOLKDZ1RbdZDnfXbwowa
4urL5HeOtKYUpLjw7z8EQ43SHZba7CsiImGcF/4OtHW1hNGNIlU/Mym93lFT5Xdq
HwDrktBWWVvBkCnxVGJjMwGGSCJbowIsPK8p8xr4CqML4Vdcx89qKB8cnCOg8Bgo
YqzcJCTOY9K5qXI8D20GaTJCP5vCPxMgmeFn4LgWa+h9iJrt+g4J8zA1qGw92nwJ
W2uRu/6YkCC2HMiyExuxkJNPKbFRbOqAm7lA/ZzuFpFU5RowACIrlwm4ZR/4UFDG
fzrt3ZfNLRu33QxqhKY0jWGeHu729+RE2kpQ4FXveFmrtRIWnuX70/+NQFVhm+qy
EBgXmlWNhTh2tcgfEzPja52+5h3SYKk6/J44266i/34x5eLDvmuRADzCVpLUmbPS
G5UHVkWHZPJne6ZJQ+yz+o2h6BjcpCTvPRbt2/KkSOo9S0Qj4/XrOUHBAofy3odH
Tdiba6lXMHZqvLlOOrMyJ0qdv26FJyJaSg5Wqhq45G1YCW5Xjc+cYzZggJBvBpIh
thyN4b9jqfTnAZzKB6LCBUmEF2A7gXkuW9oXzNUkKtVzYluu1aQ=
=tlZT
-----END PGP SIGNATURE-----
Merge tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are cleanups and minor bugfixes across several SoC specific
drivers, for Qualcomm, Samsung, NXP i.MX, AT91, Tegra, Keystone,
Renesas, ZynqMP
Noteworthy new features are:
- The op-tee firmware driver gains support for asynchronous
notifications from secure-world firmware.
- Qualcomm platforms gain support for new SoC types in various
drivers: power domain, cache controller, RPM sleep, soc-info
- Samsung SoC drivers gain support for new SoCs in ChipID and PMU, as
well as a new USIv2 driver that handles various types of serial
communiction (uart, i2c, spi)
- Renesas adds support for R-Car S4-8 (R8A779F0) in multiple drivers,
as well as memory controller support for RZ/G2L (R9A07G044).
- Apple M1 gains support for the PMGR power management driver"
* tag 'drivers-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (94 commits)
soc: qcom: rpmh-rsc: Fix typo in a comment
soc: qcom: socinfo: Add SM6350 and SM7225
dt-bindings: arm: msm: Don't mark LLCC interrupt as required
dt-bindings: firmware: scm: Add SM6350 compatible
dt-bindings: arm: msm: Add LLCC for SM6350
soc: qcom: rpmhpd: Sort power-domain definitions and lists
soc: qcom: rpmhpd: Remove mx/cx relationship on sc7280
soc: qcom: rpmhpd: Rename rpmhpd struct names
soc: qcom: rpmhpd: sm8450: Add the missing .peer for sm8450_cx_ao
soc: qcom: socinfo: add SM8450 ID
soc: qcom: rpmhpd: Add SM8450 power domains
dt-bindings: power: rpmpd: Add SM8450 to rpmpd binding
soc: qcom: smem: Update max processor count
dt-bindings: arm: qcom: Document SM8450 SoC and boards
dt-bindings: firmware: scm: Add SM8450 compatible
dt-bindings: arm: cpus: Add kryo780 compatible
soc: qcom: rpmpd: Add support for sm6125
dt-bindings: qcom-rpmpd: Add sm6125 power domains
soc: qcom: aoss: constify static struct thermal_cooling_device_ops
PM: AVS: qcom-cpr: Use div64_ul instead of do_div
...
After removal of RBTX4939 board support remove code for the TX4939 SoC.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmHO9D0ACgkQJWrqGEe9
VoRglwf/SsGcY+7vlBM1VSbUMIF/j5/xuigHIW6AxiN/hu672GMVi7nP7aHg4t3m
DpO5X6ngYFHyW79uksRfwSun/JF1mOqF4De9zhs+cy8hlV12tgEmUNB3cbv4kuFQ
e/N8/mlNrNJ2oQ1C3G3HWe3sngh2vrkhuG49t7M2TJaGAo7V4RW3z9+glNpWMb7m
YIj6gXPjPx7vuEWv80GBUcWNKBzNdRVkrQnj3C2I/ZCslnwYWBLBQxX/U9/KDkPH
7i7MgeknAlV0G/W4TfnNSAKiWOcmWdbmuJ/lOWv4+skdXoMb0/rlC6kvJqOLvbF6
2nUrc9yFTwkNfVTGJm5eWJ0yDUHMgA==
=DQck
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.17' into mtd/next
Raw NAND core:
* Export nand_read_page_hwecc_oob_first()
GPMC memory controller for OMAP2 NAND controller:
* GPMC:
- Add support for AM64 SoC and allow build on K3 platforms
- Use a compatible match table when checking for NAND controller
- Use platform_get_irq() to get the interrupt
Raw NAND controller drivers:
* OMAP2 NAND controller:
- Document the missing 'rb-gpios' DT property
- Drop unused variable
- Fix force_8bit flag behaviour for DMA mode
- Move to exec_op interface
- Use platform_get_irq() to get the interrupt
* Renesas:
- Add new NAND controller driver with its bindings and MAINTAINERS entry
* Onenand:
- Remove redundant variable ooblen
* MPC5121:
- Remove unused variable in ads5121_select_chip()
* GPMI:
- Add ERR007117 protection for nfc_apply_timings
- Remove explicit default gpmi clock setting for i.MX6
- Use platform_get_irq_byname() to get the interrupt
- Remove unneeded variable
* Ingenic:
- JZ4740 needs 'oob_first' read page function
* Davinci:
- Rewrite function description
- Avoid duplicated page read
- Don't calculate ECC when reading page
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
-----BEGIN PGP SIGNATURE-----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=eb46
-----END PGP SIGNATURE-----
Merge tag 'memory-controller-drv-omap-5.17' into nand/next
Memory controller drivers for v5.17 - OMAP GPMC
1. Add support for AM64 SoC.
2. Minor improvement: use platform_get_irq().
[miquel.raynal@bootlin.com: A first commit introduced a new omap
compatible and another moved the IDs to a header which created a
conflict: moving the new ID as well in the header fixed it.]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-3-prabhakar.mahadev-lad.rj@bp.renesas.com
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211221212609.31290-2-prabhakar.mahadev-lad.rj@bp.renesas.com
The GPMC device driver is required for NAND controller
to work on K3 Architecture. Select it if required.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-5-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
As more compatibles can be added to the GPMC NAND controller driver
use a compatible match table.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20211221131757.2030-4-rogerq@kernel.org
[krzysztof: remove "is_nand" variable]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Introduce Renesas NAND controller driver which currently supports the
following features on R-Car Gen3 and RZ/N1 SoCs:
- All ONFI timing modes
- Different configurations of its internal ECC controller
- On-die (not tested) and software ECC support
- Several chips (not tested)
- Subpage accesses
- DMA and PIO
This controller was originally provided by Evatronix before being bought
by Cadence.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/linux-mtd/20211217142033.353599-3-miquel.raynal@bootlin.com
In DMA mode we were not considering the force_8bit flag.
Fix it by using regular non-DMA 8-bit I/O if force_8bit flag is set.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211209090458.24830-6-rogerq@kernel.org
The slave_id was previously used to pick one DMA slave instead of another,
but this is now done through the DMA descriptors in device tree.
For the qcom_adm driver, the configuration is documented in the DT
binding to contain a tuple of device identifier and a "crci" field,
but the implementation ends up using only a single cell for identifying
the slave, with the crci getting passed in nonstandard properties of
the device, and passed through the dma driver using the old slave_id
field. Part of the problem apparently is that the nand driver ends up
using only a single DMA request ID, but requires distinct values for
"crci" depending on the type of transfer.
Change both the dmaengine driver and the two slave drivers to allow
the documented binding to work in addition to the ad-hoc passing
of crci values. In order to no longer abuse the slave_id field, pass
the data using the "peripheral_config" mechanism instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211122222203.4103644-9-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The NAND on Tegra belongs to the core power domain and we're going to
enable GENPD support for the core domain. Now NAND must be resumed using
runtime PM API in order to initialize the NAND power state. Add runtime PM
and OPP support to the NAND driver.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When developping NAND controller drivers or when debugging filesystem
corruptions, it is quite common to need hacking locally into the
MTD/NAND core in order to get access to the content of the bad
blocks. Instead of having multiple implementations out there let's
provide a simple yet effective specific MTD-wide debugfs entry to fully
disable these checks on purpose.
A warning is added to inform the user when this mode gets enabled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211118114659.1282855-1-miquel.raynal@bootlin.com
Variable ooblen is being initialized with a value that is never read.
The variable is never used after this, so it is redundant and can be
removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211205230729.79337-1-colin.i.king@gmail.com
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-4-herve.codina@bootlin.com
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
NAND_OP_CMD() expects a delay parameter in nanoseconds.
The delay value is wrongly given in milliseconds.
Fix the conversion macro used in order to set this
delay in nanoseconds.
Fixes: d7a773e881 ("mtd: rawnand: Access SDR and NV-DDR timings through a common macro")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-2-herve.codina@bootlin.com
The helper function devm_platform_ioremap_resource_xxx()
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: 5f14a8ca1b ("mtd: rawnand: denali: Make use of the helper function devm_platform_ioremap_resource_byname()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211109134758.417-1-caihuoqing@baidu.com
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
There is no need to explicitly set the default gpmi clock rate during
boot for the i.MX 6 since this is done during nand_detect anyway.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-1-ceggers@arri.de
The ECC engine on the JZ4740 SoC requires the ECC data to be read before
the page; using the default page reading function does not work. Indeed,
the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag
that existed back then.
Use the newly created nand_read_page_hwecc_oob_first() to address this
issue.
This issue was not found when the new ingenic-nand driver was developed,
most likely because the Device Tree used had the nand-ecc-mode set to
"hw_oob_first", which seems to not be supported anymore.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-5-paul@crapouillou.net
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
* Remove obsolete macros only used by the old nand_ecclayout struct
* Don't remove debugfs directory if device is in use
* MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
* block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
* mtdswap: Remove redundant assignment of pointer eb
CFI:
* Fixup CFI on ixp4xx
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
* Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
* Enable locking for n25q128a13
SPI NOR controller drivers:
* Use devm_platform_ioremap_resource_byname()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmGIAdEACgkQJWrqGEe9
VoQHEAgAkFvFxIOyPSwAJfyeEklWmGSh+cm+X9EqWxZ5d6iwFE3FZH4X4XiqdyVY
+rzy37o6Tp3pQVYDqxmPM8GGoHy8wYPR5h/U1IozbBaNeCJma1HyK4Sjb/cuX1eQ
23EM1pWT8N9CbRG2S9mz5C9uHcP9mImtyvU4WhTLKOEc9XGbpuj+k1cacSuEEbeF
rZklOa7tvUiOFIDfr7Kf+DfxbpYabgB2dJgWPEtZmKmefWMiODHgvBJo0MT6MKr7
kOlIkgq5zYIFRNaxApWLI3JmH9+lsw6MHBe+cCqemV6q2OZlMV/5VGFElEywJt+4
L3VmlJQpMiCEMo2Cgc1jigHKryk4Xw==
=h6o3
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core:
- Remove obsolete macros only used by the old nand_ecclayout struct
- Don't remove debugfs directory if device is in use
- MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
- block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
- mtdswap: Remove redundant assignment of pointer eb
CFI:
- Fixup CFI on ixp4xx
Raw NAND controller drivers:
- Arasan:
- Prevent an unsupported configuration
- Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd,
AMS-Delta:
- Keep the driver compatible with on-die ECC engines
- cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
- Fsmc: Fix use of SM ORDER
- Intel:
- Fix potential buffer overflow in probe
- xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk,
hisi504, gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
- Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
- Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
- Enable locking for n25q128a13
SPI NOR controller drivers:
- Use devm_platform_ioremap_resource_byname()"
* tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: core: don't remove debugfs directory if device is in use
MAINTAINERS: Update the devicetree documentation path of hyperbus
mtd: block2mtd: add support for an optional custom MTD label
mtd: block2mtd: minor refactor to avoid hard coded constant
mtd: fixup CFI on ixp4xx
mtd: rawnand: arasan: Prevent an unsupported configuration
MAINTAINERS: Add entry for Qualcomm NAND controller driver
mtd: rawnand: hynix: Add support for H27UCG8T2ETR-BC MLC NAND
mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
Revert "mtd: rawnand: cs553x: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: lpc32xx_slc: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: ndfc: Fix external use of SW Hamming ECC helper"
...
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde60314 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
This reverts commit 56a8d3fd1f.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-9-miquel.raynal@bootlin.com
This reverts commit c4b7d7c480.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-8-miquel.raynal@bootlin.com
This reverts commit 3e09c02525.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-7-miquel.raynal@bootlin.com
This reverts commit 46fcb57e6b.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-6-miquel.raynal@bootlin.com
This reverts commit 6a4c5ada57.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-5-miquel.raynal@bootlin.com
This reverts commit 3d227a0b0c.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-4-miquel.raynal@bootlin.com
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
Enhancing the implementation of the rawnand_ecc_sw_* helpers to support
both cases, when the ECC object is instantiated and when it is not is a
quite elegant way to solve this situation. This way, we can still use
the existing and exported rawnand helpers while avoiding the need for
each driver to declare its own helper.
Following this change, most of the fixes sent in [2] can now be safely
reverted. Only the fsmc fix will need to be kept because there is
actually something specific to the driver to do in its ->correct()
helper.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com/
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-3-miquel.raynal@bootlin.com
The introduction of the generic ECC engine API lead to a number of
changes in various drivers which broke some of them. Here is a typical
example: I expected the SM_ORDER option to be handled by the Hamming ECC
engine internals. Problem: the fsmc driver does not instantiate (yet) a
real ECC engine object so we had to use a 'bare' ECC helper instead of
the shiny rawnand functions. However, when not intializing this engine
properly and using the bare helpers, we do not get the SM ORDER feature
handled automatically. It looks like this was lost in the process so
let's ensure we use the right SM ORDER now.
Fixes: ad9ffdce45 ("mtd: rawnand: fsmc: Fix external use of SW Hamming ECC helper")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-2-miquel.raynal@bootlin.com
None of supported Samsung Exynos4 SoCs (Exynos4210, Exynos4412) seem to
use OneNAND driver so drop it. Describe better which driver applies to
which SoC, to make configuring kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210924133223.111930-1-krzysztof.kozlowski@canonical.com
From QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_nandc_read_cw_raw() is used to read only one code word
at a time. If we will configure number of code words to 1 in
in QPIC_NAND_DEV0_CFG0 register then QPIC controller thinks
its reading the last code word, since from QPIC V2 onwards
we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n"
register to fetch data from controller buffer to system
memory.
Fixes: 503ee5aad4 ("mtd: rawnand: qcom: update last code word register")
Cc: stable@kernel.org
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1630998357-1359-1-git-send-email-mdalam@codeaurora.org
ebu_nand_probe() read the value of u32 variable "cs" from the device
firmware description and used it as the index for array ebu_host->cs
that can contain MAX_CS (2) elements at most. That could result in
a buffer overflow and various bad consequences later.
Fix the potential buffer overflow by restricting values of "cs" with
MAX_CS in probe.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210903082653.16441-1-novikov@ispras.ru
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074252.9633-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074245.9583-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074237.9533-1-caihuoqing@baidu.com
